[PATCH v6 10/11] vpl: Add Kconfig options for VPL

Add VPL versions of commonly used Kconfig options.

Signed-off-by: Simon Glass sjg@chromium.org ---

(no changes since v5)

Changes in v5: - Rebase this patch on mainline (for GPIO and MISC Kconfig renames)

Changes in v4: - Add options for blk, core, misc and tpl also - Add VPL_SIZE_LIMIT

Kconfig | 10 ++ common/Kconfig | 67 +++++++++++++ common/spl/Kconfig | 202 +++++++++++++++++++++++++++++++++++++++ drivers/block/Kconfig | 12 +++ drivers/clk/Kconfig | 10 ++ drivers/core/Kconfig | 33 +++++++ drivers/core/Makefile | 2 +- drivers/gpio/Kconfig | 11 +++ drivers/i2c/Kconfig | 11 +++ drivers/misc/Kconfig | 28 ++++++ drivers/pinctrl/Kconfig | 18 +++- drivers/rtc/Kconfig | 9 ++ drivers/serial/Kconfig | 20 ++++ drivers/sysreset/Kconfig | 10 ++ drivers/timer/Kconfig | 10 ++ drivers/tpm/Kconfig | 30 ++++++ dts/Kconfig | 9 ++ lib/Kconfig | 62 ++++++++++++ 18 files changed, 551 insertions(+), 3 deletions(-)

diff --git a/Kconfig b/Kconfig index a6c42b902f7..60af7da0e78 100644 --- a/Kconfig +++ b/Kconfig @@ -279,6 +279,16 @@ config TPL_SYS_MALLOC_F_LEN particular needs this to operate, so that it can allocate the initial serial device and any others that are needed.

+config VPL_SYS_MALLOC_F_LEN + hex "Size of malloc() pool in VPL before relocation" + depends on SYS_MALLOC_F && VPL + default SYS_MALLOC_F_LEN + help + Before relocation, memory is very limited on many platforms. Still, + we can provide a small malloc() pool if needed. Driver model in + particular needs this to operate, so that it can allocate the + initial serial device and any others that are needed. + menuconfig EXPERT bool "Configure standard U-Boot features (expert users)" default y diff --git a/common/Kconfig b/common/Kconfig index f87fb5b426e..88b82c1c5e7 100644 --- a/common/Kconfig +++ b/common/Kconfig @@ -81,6 +81,15 @@ config TPL_LOGLEVEL int default LOGLEVEL

+config VPL_LOGLEVEL + int "loglevel for VPL" + default LOGLEVEL + help + All Messages with a loglevel smaller than the console loglevel will + be compiled in to VPL. See LOGLEVEL for a list of available log + levels. Setting this to a value above 4 may increase the code size + significantly. + config SILENT_CONSOLE bool "Support a silent console" help @@ -254,6 +263,15 @@ config LOG

if LOG

+config VPL_LOG + bool "Enable logging support in VPL" + depends on LOG + help + This enables support for logging of status and debug messages. These + can be displayed on the console, recorded in a memory buffer, or + discarded if not needed. Logging supports various categories and + levels of severity. + config LOG_MAX_LEVEL int "Maximum log level to record" default 6 @@ -423,6 +441,47 @@ config TPL_LOG_CONSOLE

endif

+config VPL_LOG + bool "Enable logging support in VPL" + depends on LOG + help + This enables support for logging of status and debug messages. These + can be displayed on the console, recorded in a memory buffer, or + discarded if not needed. Logging supports various categories and + levels of severity. + +if VPL_LOG + +config VPL_LOG_MAX_LEVEL + int "Maximum log level to record in VPL" + default 3 + help + This selects the maximum log level that will be recorded. Any value + higher than this will be ignored. If possible log statements below + this level will be discarded at build time. Levels: + + 0 - emergency + 1 - alert + 2 - critical + 3 - error + 4 - warning + 5 - note + 6 - info + 7 - debug + 8 - debug content + 9 - debug hardware I/O + +config VPL_LOG_CONSOLE + bool "Allow log output to the console in VPL" + default y + help + Enables a log driver which writes log records to the console. + Generally the console is the serial port or LCD display. Only the + log message is shown - other details like level, category, file and + line number are omitted. + +endif + config LOG_ERROR_RETURN bool "Log all functions which return an error" help @@ -718,6 +777,14 @@ config TPL_BLOBLIST This enables a bloblist in TPL. The bloblist is set up in TPL and passed to SPL and U-Boot proper.

+config VPL_BLOBLIST + bool "Support for a bloblist in VPL" + depends on BLOBLIST && VPL_LIBGENERIC_SUPPORT && VPL_LIBCOMMON_SUPPORT + default y if VPL + help + This enables a bloblist in VPL. The bloblist is set up in VPL and + passed to SPL and U-Boot proper. + config BLOBLIST_SIZE hex "Size of bloblist" depends on BLOBLIST diff --git a/common/spl/Kconfig b/common/spl/Kconfig index babbcbe9423..6deb42e3355 100644 --- a/common/spl/Kconfig +++ b/common/spl/Kconfig @@ -1585,6 +1585,208 @@ config TPL_YMODEM_SUPPORT

endif # TPL

+config VPL + bool + depends on SUPPORT_SPL + prompt "Enable VPL" + help + If you want to build VPL as well as the normal image, TPL and SPL, + say Y. + +if VPL + +config VPL_BANNER_PRINT + bool "Enable output of the VPL banner 'U-Boot VPL ...'" + depends on VPL + default y + help + If this option is enabled, VPL will print the banner with version + info. Disabling this option could be useful to reduce VPL boot time + (e.g. approx. 6 ms faster, when output on i.MX6 with 115200 baud). + +config VPL_BOARD_INIT + bool "Call board-specific initialization in VPL" + help + If this option is enabled, U-Boot will call the function + spl_board_init() from board_init_r(). This function should be + provided by the board. + +config VPL_CACHE + depends on CACHE + bool "Support cache drivers in VPL" + help + Enable support for cache drivers in VPL. + +config VPL_DM_SPI + bool "Support SPI DM drivers in VPL" + help + Enable support for SPI DM drivers in VPL. + +config VPL_DM_SPI_FLASH + bool "Support SPI DM FLASH drivers in VPL" + help + Enable support for SPI DM flash drivers in VPL. + +config VPL_FRAMEWORK + bool "Support VPL based upon the common SPL framework" + default y + help + Enable the SPL framework under common/spl/ for VPL builds. + This framework supports MMC, NAND and YMODEM and other methods + loading of U-Boot's next stage. If unsure, say Y. + +config VPL_HANDOFF + bool "Pass hand-off information from VPL to SPL" + depends on HANDOFF && VPL_BLOBLIST + default y + help + This option enables VPL to write handoff information. This can be + used to pass information like the size of SDRAM from VPL to SPL. Also + VPL can receive information from TPL in the same place if that is + enabled. + +config VPL_LIBCOMMON_SUPPORT + bool "Support common libraries" + default y if SPL_LIBCOMMON_SUPPORT + help + Enable support for common U-Boot libraries within VPL. See + SPL_LIBCOMMON_SUPPORT for details. + +config VPL_LIBGENERIC_SUPPORT + bool "Support generic libraries" + default y if SPL_LIBGENERIC_SUPPORT + help + Enable support for generic U-Boot libraries within VPL. These + libraries include generic code to deal with device tree, hashing, + printf(), compression and the like. This option is enabled on many + boards. Enable this option to build the code in lib/ as part of a + VPL build. + +config VPL_DRIVERS_MISC + bool "Support misc drivers" + default y if TPL_DRIVERS_MISC + help + Enable miscellaneous drivers in VPL. These drivers perform various + tasks that don't fall nicely into other categories, Enable this + option to build the drivers in drivers/misc as part of a VPL + build, for those that support building in VPL (not all drivers do). + +config VPL_ENV_SUPPORT + bool "Support an environment" + help + Enable environment support in VPL. The U-Boot environment provides + a number of settings (essentially name/value pairs) which can + control many aspects of U-Boot's operation. Enabling this option will + make env_get() and env_set() available in VSPL. + +config VPL_GPIO + bool "Support GPIO in VPL" + default y if SPL_GPIO + help + Enable support for GPIOs (General-purpose Input/Output) in VPL. + GPIOs allow U-Boot to read the state of an input line (high or + low) and set the state of an output line. This can be used to + drive LEDs, control power to various system parts and read user + input. GPIOs can be useful in VPL to enable a 'sign-of-life' LED, + for example. Enable this option to build the drivers in + drivers/gpio as part of a VPL build. + +config VPL_HANDOFF + bool "Pass hand-off information from VPL to SPL and U-Boot proper" + depends on HANDOFF && VPL_BLOBLIST + default y + help + This option enables VPL to write handoff information. This can be + used to pass information like the size of SDRAM from VPL to U-Boot + proper. The information is also available to VPL if it is useful + there. + +config VPL_HASH_SUPPORT + bool "Support hashing drivers in VPL" + depends on VPL + select SHA1 + select SHA256 + help + Enable hashing drivers in VPL. These drivers can be used to + accelerate secure boot processing in secure applications. Enable + this option to build system-specific drivers for hash acceleration + as part of a VPL build. + +config VPL_I2C_SUPPORT + bool "Support I2C in VPL" + default y if SPL_I2C_SUPPORT + help + Enable support for the I2C bus in VPL. Vee SPL_I2C_SUPPORT for + details. + +config VPL_PCH_SUPPORT + bool "Support PCH drivers" + default y if TPL_PCH_SUPPORT + help + Enable support for PCH (Platform Controller Hub) devices in VPL. + These are used to set up GPIOs and the SPI peripheral early in + boot. This enables the drivers in drivers/pch as part of a VPL + build. + +config VPL_PCI + bool "Support PCI drivers" + default y if SPL_PCI + help + Enable support for PCI in VPL. For platforms that need PCI to boot, + or must perform some init using PCI in VPL, this provides the + necessary driver support. This enables the drivers in drivers/pci + as part of a VPL build. + +config VPL_RTC_SUPPORT + bool "Support RTC drivers" + help + Enable RTC (Real-time Clock) support in VPL. This includes support + for reading and setting the time. Some RTC devices also have some + non-volatile (battery-backed) memory which is accessible if + needed. This enables the drivers in drivers/rtc as part of a VPL + build. + +config VPL_SERIAL_SUPPORT + bool "Support serial" + default y if SPL_SERIAL_SUPPORT + select VPL_PRINTF + select VPL_STRTO + help + Enable support for serial in VPL. See SPL_SERIAL_SUPPORT for + details. + +config VPL_SIZE_LIMIT + hex "Maximum size of VPL image" + depends on VPL + default 0x0 + help + Specifies the maximum length of the U-Boot VPL image. + If this value is zero, it is ignored. + +config VPL_SPI_SUPPORT + bool "Support SPI drivers" + help + Enable support for using SPI in VPL. See SPL_SPI_SUPPORT for + details. + +config VPL_SPI_FLASH_SUPPORT + bool "Support SPI flash drivers" + help + Enable support for using SPI flash in VPL, and loading U-Boot from + SPI flash. SPI flash (Serial Peripheral Bus flash) is named after + the SPI bus that is used to connect it to a system. It is a simple + but fast bidirectional 4-wire bus (clock, chip select and two data + lines). This enables the drivers in drivers/mtd/spi as part of a + VPL build. This normally requires VPL_SPI_SUPPORT. + +config VPL_TEXT_BASE + hex "VPL Text Base" + default 0x0 + help + The address in memory that VPL will be running from. + +endif # VPL + config SPL_AT91_MCK_BYPASS bool "Use external clock signal as a source of main clock for AT91 platforms" depends on ARCH_AT91 diff --git a/drivers/block/Kconfig b/drivers/block/Kconfig index 4023332dd98..8cb43f5e207 100644 --- a/drivers/block/Kconfig +++ b/drivers/block/Kconfig @@ -39,6 +39,18 @@ config TPL_BLK be partitioned into several areas, called 'partitions' in U-Boot. A filesystem can be placed in each partition.

+config VPL_BLK + bool "Support block devices in VPL" + depends on VPL_DM && BLK + default y + help + Enable support for block devices, such as SCSI, MMC and USB + flash sticks. These provide a block-level interface which permits + reading, writing and (in some cases) erasing blocks. Block + devices often have a partition table which allows the device to + be partitioned into several areas, called 'partitions' in U-Boot. + A filesystem can be placed in each partition. + config BLOCK_CACHE bool "Use block device cache" depends on BLK diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig index baac8d281e4..dda65e820dd 100644 --- a/drivers/clk/Kconfig +++ b/drivers/clk/Kconfig @@ -30,6 +30,16 @@ config TPL_CLK setting up clocks within TPL, and allows the same drivers to be used as U-Boot proper.

+config VPL_CLK + bool "Enable clock support in VPL" + depends on CLK && VPL_DM + help + The clock subsystem adds a small amount of overhead to the image. + If this is acceptable and you have a need to use clock drivers in + SPL, enable this option. It might provide a cleaner interface to + setting up clocks within TPL, and allows the same drivers to be + used as U-Boot proper. + config CLK_BCM6345 bool "Clock controller driver for BCM6345" depends on CLK && ARCH_BMIPS diff --git a/drivers/core/Kconfig b/drivers/core/Kconfig index 9ae188c1dfc..33ef6a362f0 100644 --- a/drivers/core/Kconfig +++ b/drivers/core/Kconfig @@ -35,6 +35,16 @@ config TPL_DM CONFIG_SPL_SYS_MALLOC_F_LEN for more details on how to enable it. Disable this for very small implementations.

+config VPL_DM + bool "Enable Driver Model for VPL" + depends on DM && VPL + default y if SPL_DM + help + Enable driver model in VPL. You will need to provide a + suitable malloc() implementation. If you are not using the + full malloc() enabled by CONFIG_SYS_SPL_MALLOC_START, + consider using CONFIG_SYS_MALLOC_SIMPLE. + config DM_WARN bool "Enable warnings in driver model" depends on DM @@ -113,6 +123,15 @@ config SPL_DM_SEQ_ALIAS numbered devices (e.g. serial0 = &serial0). This feature can be disabled if it is not required, to save code space in SPL.

+config VPL_DM_SEQ_ALIAS + bool "Support numbered aliases in device tree in VPL" + depends on VPL_DM + default y + help + Most boards will have a '/aliases' node containing the path to + numbered devices (e.g. serial0 = &serial0). This feature can be + disabled if it is not required, to save code space in VPL. + config SPL_DM_INLINE_OFNODE bool "Inline some ofnode functions which are seldom used in SPL" depends on SPL_DM @@ -286,6 +305,20 @@ config SPL_OF_TRANSLATE used for the address translation. This function is faster and smaller in size than fdt_translate_address().

+config VPL_OF_TRANSLATE + bool "Translate addresses using fdt_translate_address in SPL" + depends on SPL_DM && VPL_OF_CONTROL + help + If this option is enabled, the reg property will be translated + using the fdt_translate_address() function. This is necessary + on some platforms (e.g. MVEBU) using complex "ranges" + properties in many nodes. As this translation is not handled + correctly in the default simple_bus_translate() function. + + If this option is not enabled, simple_bus_translate() will be + used for the address translation. This function is faster and + smaller in size than fdt_translate_address(). + config TRANSLATION_OFFSET bool "Platforms specific translation offset" depends on DM && OF_CONTROL diff --git a/drivers/core/Makefile b/drivers/core/Makefile index 5edd4e41357..07a0886383f 100644 --- a/drivers/core/Makefile +++ b/drivers/core/Makefile @@ -5,7 +5,7 @@ obj-y += device.o fdtaddr.o lists.o root.o uclass.o util.o obj-$(CONFIG_$(SPL_TPL_)ACPIGEN) += acpi.o obj-$(CONFIG_DEVRES) += devres.o -obj-$(CONFIG_$(SPL_)DM_DEVICE_REMOVE) += device-remove.o +obj-$(CONFIG_$(SPL_TPL_)DM_DEVICE_REMOVE) += device-remove.o obj-$(CONFIG_$(SPL_)SIMPLE_BUS) += simple-bus.o obj-$(CONFIG_SIMPLE_PM_BUS) += simple-pm-bus.o obj-$(CONFIG_DM) += dump.o diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index e37ac9f4941..ec0de98687f 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -36,6 +36,17 @@ config TPL_DM_GPIO particular GPIOs that they provide. The uclass interface is defined in include/asm-generic/gpio.h.

+config VPL_DM_GPIO + bool "Enable Driver Model for GPIO drivers in VPL" + depends on DM_GPIO && VPL_DM && VPL_GPIO + default y + help + Enable driver model for GPIO access in VPL. The standard GPIO + interface (gpio_get_value(), etc.) is then implemented by + the GPIO uclass. Drivers provide methods to query the + particular GPIOs that they provide. The uclass interface + is defined in include/asm-generic/gpio.h. + config GPIO_HOG bool "Enable GPIO hog support" depends on DM_GPIO diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig index 63d03a3cebf..308198a44d5 100644 --- a/drivers/i2c/Kconfig +++ b/drivers/i2c/Kconfig @@ -47,6 +47,17 @@ config SPL_DM_I2C device (bus child) info is kept as parent platdata. The interface is defined in include/i2c.h.

+config VPL_DM_I2C + bool "Enable Driver Model for I2C drivers in VPL" + depends on VPL_DM && DM_I2C + default y + help + Enable driver model for I2C. The I2C uclass interface: probe, read, + write and speed, is implemented with the bus drivers operations, + which provide methods for bus setting and data transfer. Each chip + device (bus child) info is kept as parent platdata. The interface + is defined in include/i2c.h. + config I2C_CROS_EC_TUNNEL tristate "Chrome OS EC tunnel I2C bus" depends on CROS_EC diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index 997b7132211..dca25dea56c 100644 --- a/drivers/misc/Kconfig +++ b/drivers/misc/Kconfig @@ -122,6 +122,16 @@ config TPL_CROS_EC control access to the battery and main PMIC depending on the device. You can use the 'crosec' command to access it.

+config VPL_CROS_EC + bool "Enable Chrome OS EC in VPL" + depends on VPL + help + Enable access to the Chrome OS EC in VPL. This is a separate + microcontroller typically available on a SPI bus on Chromebooks. It + provides access to the keyboard, some internal storage and may + control access to the battery and main PMIC depending on the + device. You can use the 'crosec' command to access it. + config CROS_EC_I2C bool "Enable Chrome OS EC I2C driver" depends on CROS_EC @@ -158,6 +168,15 @@ config TPL_CROS_EC_LPC through a legacy port interface, so on x86 machines the main function of the EC is power and thermal management.

+config VPL_CROS_EC_LPC + bool "Enable Chrome OS EC LPC driver in VPL" + depends on CROS_EC + help + Enable I2C access to the Chrome OS EC. This is used on x86 + Chromebooks such as link and falco. The keyboard is provided + through a legacy port interface, so on x86 machines the main + function of the EC is power and thermal management. + config CROS_EC_SANDBOX bool "Enable Chrome OS EC sandbox driver" depends on CROS_EC && SANDBOX @@ -185,6 +204,15 @@ config TPL_CROS_EC_SANDBOX EC flash read/write/erase support and a few other things. It is enough to perform a Chrome OS verified boot on sandbox.

+config VPL_CROS_EC_SANDBOX + bool "Enable Chrome OS EC sandbox driver in VPL" + depends on VPL_CROS_EC && SANDBOX + help + Enable a sandbox emulation of the Chrome OS EC in VPL. This supports + keyboard (use the -l flag to enable the LCD), verified boot context, + EC flash read/write/erase support and a few other things. It is + enough to perform a Chrome OS verified boot on sandbox. + config CROS_EC_SPI bool "Enable Chrome OS EC SPI driver" depends on CROS_EC diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 30eaa376c8e..704bd032e55 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -89,20 +89,34 @@ config TPL_PINCTRL This option is an TPL variant of the PINCTRL option. See the help of PINCTRL for details.

+config VPL_PINCTRL + bool "Support pin controllers in VPL" + depends on VPL && VPL_DM + help + This option is an VPL variant of the PINCTRL option. + See the help of PINCTRL for details. + config SPL_PINCTRL_FULL bool "Support full pin controllers in SPL" depends on SPL_PINCTRL && SPL_OF_CONTROL default n if TARGET_STM32F746_DISCO default y help - This option is an SPL-variant of the PINCTRL_FULL option. + This option is an SPL variant of the PINCTRL_FULL option. See the help of PINCTRL_FULL for details.

config TPL_PINCTRL_FULL bool "Support full pin controllers in TPL" depends on TPL_PINCTRL && TPL_OF_CONTROL help - This option is an TPL-variant of the PINCTRL_FULL option. + This option is a TPL variant of the PINCTRL_FULL option. + See the help of PINCTRL_FULL for details. + +config VPL_PINCTRL_FULL + bool "Support full pin controllers in VPL" + depends on VPL_PINCTRL && VPL_OF_CONTROL + help + This option is a VPL variant of the PINCTRL_FULL option. See the help of PINCTRL_FULL for details.

config SPL_PINCTRL_GENERIC diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig index b6692e62df1..19792679018 100644 --- a/drivers/rtc/Kconfig +++ b/drivers/rtc/Kconfig @@ -32,6 +32,15 @@ config TPL_DM_RTC drivers to perform the actual functions. See rtc.h for a description of the API.

+config VPL_DM_RTC + bool "Enable Driver Model for RTC drivers in VPL" + depends on VPL_DM + help + Enable drver model for real-time-clock drivers. The RTC uclass + then provides the rtc_get()/rtc_set() interface, delegating to + drivers to perform the actual functions. See rtc.h for a + description of the API. + config RTC_ENABLE_32KHZ_OUTPUT bool "Enable RTC 32Khz output" help diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 93348c0929c..a5142606c71 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -63,6 +63,16 @@ config TPL_SERIAL_PRESENT This option enables the full UART in TPL, so if is it disabled, the full UART driver will be omitted, thus saving space.

+config VPL_SERIAL_PRESENT + bool "Provide a serial driver in VPL" + depends on DM_SERIAL && VPL + default y + help + In very space-constrained devices even the full UART driver is too + large. In this case the debug UART can still be used in some cases. + This option enables the full UART in TPL, so if is it disabled, + the full UART driver will be omitted, thus saving space. + # Logic to allow us to use the imply keyword to set what the default port # should be. The default is otherwise 1. config CONS_INDEX_0 @@ -172,6 +182,16 @@ config TPL_DM_SERIAL implements serial_putc() etc. The uclass interface is defined in include/serial.h.

+config VPL_DM_SERIAL + bool "Enable Driver Model for serial drivers in VPL" + depends on DM_SERIAL + default y if VPL && DM_SERIAL + help + Enable driver model for serial in VPL. This replaces + drivers/serial/serial.c with the serial uclass, which + implements serial_putc() etc. The uclass interface is + defined in include/serial.h. + config DEBUG_UART bool "Enable an early debug UART for debugging" help diff --git a/drivers/sysreset/Kconfig b/drivers/sysreset/Kconfig index ac77ffbc8be..fec6fed6c31 100644 --- a/drivers/sysreset/Kconfig +++ b/drivers/sysreset/Kconfig @@ -31,6 +31,16 @@ config TPL_SYSRESET to effect a reset. The uclass will try all available drivers when reset_walk() is called.

+config VPL_SYSRESET + bool "Enable support for system reset drivers in VPL mode" + depends on SYSRESET && VPL_DM + default y if TPL_SYSRESET + help + Enable system reset drivers which can be used to reset the CPU or + board. Each driver can provide a reset method which will be called + to effect a reset. The uclass will try all available drivers when + reset_walk() is called. + if SYSRESET

config SYSRESET_CMD_RESET diff --git a/drivers/timer/Kconfig b/drivers/timer/Kconfig index 89131426542..47dfd9c559b 100644 --- a/drivers/timer/Kconfig +++ b/drivers/timer/Kconfig @@ -27,6 +27,16 @@ config TPL_TIMER function. This enables the drivers in drivers/timer as part of an TPL build.

+config VPL_TIMER + bool "Enable driver model for timer drivers in VPL" + depends on TIMER && VPL + default y if TPL_TIMER + help + Enable support for timer drivers in VPL. These can be used to get + a timer value when in VPL, or perhaps for implementing a delay + function. This enables the drivers in drivers/timer as part of an + TPL build. + config TIMER_EARLY bool "Allow timer to be used early in U-Boot" depends on TIMER diff --git a/drivers/tpm/Kconfig b/drivers/tpm/Kconfig index 9eebab5cfd9..48864f29770 100644 --- a/drivers/tpm/Kconfig +++ b/drivers/tpm/Kconfig @@ -137,6 +137,36 @@ config TPM2_CR50_I2C trust for a device, It operates like a TPM and can be used with verified boot. Cr50 is used on recent Chromebooks (since 2017).

+config SPL_TPM2_CR50_I2C + bool "Enable support for Google cr50 TPM" + depends on DM_I2C && SPL_TPM + help + Cr50 is an implementation of a TPM on Google's H1 security chip. + This uses the same open-source firmware as the Chromium OS EC. + While Cr50 has other features, its primary role is as the root of + trust for a device, It operates like a TPM and can be used with + verified boot. Cr50 is used on recent Chromebooks (since 2017). + +config TPL_TPM2_CR50_I2C + bool "Enable support for Google cr50 TPM" + depends on DM_I2C && TPL_TPM + help + Cr50 is an implementation of a TPM on Google's H1 security chip. + This uses the same open-source firmware as the Chromium OS EC. + While Cr50 has other features, its primary role is as the root of + trust for a device, It operates like a TPM and can be used with + verified boot. Cr50 is used on recent Chromebooks (since 2017). + +config VPL_TPM2_CR50_I2C + bool "Enable support for Google cr50 TPM" + depends on DM_I2C && VPL_TPM + help + Cr50 is an implementation of a TPM on Google's H1 security chip. + This uses the same open-source firmware as the Chromium OS EC. + While Cr50 has other features, its primary role is as the root of + trust for a device, It operates like a TPM and can be used with + verified boot. Cr50 is used on recent Chromebooks (since 2017). + config TPM2_TIS_SANDBOX bool "Enable sandbox TPMv2.x driver" depends on TPM_V2 && SANDBOX diff --git a/dts/Kconfig b/dts/Kconfig index dabe0080c1e..4a6cb3a8af3 100644 --- a/dts/Kconfig +++ b/dts/Kconfig @@ -76,6 +76,15 @@ config TPL_OF_CONTROL which is not enough to support device tree. Enable this option to allow such boards to be supported by U-Boot TPL.

+config VPL_OF_CONTROL + bool "Enable run-time configuration via Device Tree in VPL" + depends on VPL && OF_CONTROL + default y if SPL_OF_CONTROL + help + Some boards use device tree in U-Boot but only have 4KB of SRAM + which is not enough to support device tree. Enable this option to + allow such boards to be supported by U-Boot VPL. + config OF_LIVE bool "Enable use of a live tree" depends on DM && OF_CONTROL diff --git a/lib/Kconfig b/lib/Kconfig index 130fa0630ac..15d2ca8c047 100644 --- a/lib/Kconfig +++ b/lib/Kconfig @@ -80,6 +80,11 @@ config TPL_PRINTF select TPL_SPRINTF select TPL_STRTO if !TPL_USE_TINY_PRINTF

+config VPL_PRINTF + bool + select VPL_SPRINTF + select VPL_STRTO if !VPL_USE_TINY_PRINTF + config SPRINTF bool default y @@ -90,6 +95,9 @@ config SPL_SPRINTF config TPL_SPRINTF bool

+config VPL_SPRINTF + bool + config SSCANF bool default n @@ -104,6 +112,9 @@ config SPL_STRTO config TPL_STRTO bool

+config VPL_STRTO + bool + config IMAGE_SPARSE bool

@@ -156,6 +167,17 @@ config TPL_USE_TINY_PRINTF

The supported format specifiers are %c, %s, %u/%d and %x.

+config VPL_USE_TINY_PRINTF + bool "Enable tiny printf() version for VPL" + depends on VPL + help + This option enables a tiny, stripped down printf version. + This should only be used in space limited environments, + like SPL versions with hard memory limits. This version + reduces the code size by about 2.5KiB on armv7. + + The supported format specifiers are %c, %s, %u/%d and %x. + config PANIC_HANG bool "Do not reset the system on fatal error" help @@ -341,6 +363,17 @@ config TPL_TPM for the low-level TPM interface, but only one TPM is supported at a time by the TPM library.

+config VPL_TPM + bool "Trusted Platform Module (TPM) Support in VPL" + depends on VPL_DM + help + This enables support for TPMs which can be used to provide security + features for your board. The TPM can be connected via LPC or I2C + and a sandbox TPM is provided for testing purposes. Use the 'tpm' + command to interactive the TPM. Driver model support is provided + for the low-level TPM interface, but only one TPM is supported at + a time by the TPM library. + endmenu

menu "Android Verified Boot" @@ -524,6 +557,12 @@ config SPL_LZMA help This enables support for LZMA compression algorithm for SPL boot.

+config VPL_LZMA + bool "Enable LZMA decompression support for VPL build" + default y if LZMA + help + This enables support for LZMA compression algorithm for VPL boot. + config SPL_LZO bool "Enable LZO decompression support in SPL" help @@ -603,6 +642,7 @@ config OF_LIBFDT_OVERLAY

config SPL_OF_LIBFDT bool "Enable the FDT library for SPL" + depends on SPL_LIBGENERIC_SUPPORT default y if SPL_OF_CONTROL help This enables the FDT library (libfdt). It provides functions for @@ -624,6 +664,7 @@ config SPL_OF_LIBFDT_ASSUME_MASK

config TPL_OF_LIBFDT bool "Enable the FDT library for TPL" + depends on TPL_LIBGENERIC_SUPPORT default y if TPL_OF_CONTROL help This enables the FDT library (libfdt). It provides functions for @@ -643,6 +684,27 @@ config TPL_OF_LIBFDT_ASSUME_MASK 0xff means all assumptions are made and any invalid data may cause unsafe execution. See FDT_ASSUME_PERFECT, etc. in libfdt_internal.h

+config VPL_OF_LIBFDT + bool "Enable the FDT library for VPL" + default y if VPL_OF_CONTROL && !VPL_OF_PLATDATA + help + This enables the FDT library (libfdt). It provides functions for + accessing binary device tree images in memory, such as adding and + removing nodes and properties, scanning through the tree and finding + particular compatible nodes. The library operates on a flattened + version of the device tree. + +config VPL_OF_LIBFDT_ASSUME_MASK + hex "Mask of conditions to assume for libfdt" + depends on VPL_OF_LIBFDT || FIT + default 0xff + help + Use this to change the assumptions made by libfdt in SPL about the + device tree it is working with. A value of 0 means that no assumptions + are made, and libfdt is able to deal with malicious data. A value of + 0xff means all assumptions are made and any invalid data may cause + unsafe execution. See FDT_ASSUME_PERFECT, etc. in libfdt_internal.h + config FDT_FIXUP_PARTITIONS bool "overwrite MTD partitions in DTS through defined in 'mtdparts'" depends on OF_LIBFDT