On 3/16/22 04:03, Simon Glass wrote:
This is an attempt to cover the common cases found when enabling driver model for serial on a new board.
Signed-off-by: Simon Glass sjg@chromium.org
Changes in v2:
Add an example patch
Mention removing old code that is not used
doc/develop/driver-model/serial-howto.rst | 152 ++++++++++++++++++++++ 1 file changed, 152 insertions(+)
diff --git a/doc/develop/driver-model/serial-howto.rst b/doc/develop/driver-model/serial-howto.rst index 1469131124b..e595049c0a3 100644 --- a/doc/develop/driver-model/serial-howto.rst +++ b/doc/develop/driver-model/serial-howto.rst @@ -44,3 +44,155 @@ this involves these steps:
- build and get u-boot-dtb.bin so you can test it
- Your drivers can now use device tree
- For device tree in SPL, define CONFIG_SPL_OF_CONTROL
+Converting boards to CONFIG_DM_SERIAL +-------------------------------------
+If your SoC has a serial driver that uses driver model (has U_BOOT_DRIVER() in
%s/uses/uses the/
+it) then you may still find that your board has not been converted. To convert +your board, enable the option and see if you can get it working.
+Firstly you will have a lot more success if you have a method of debugging your +board, such as a JTAG connection. Failing that the debug UART is useful, +although since you are trying to get the UART driver running, it will interfere +with your efforts eventually.
+Secondly, while the UART is a relatively simple peripheral, it may need quite a +few pieces to be up and running before it will work, such as the correct pin +muxing, clocks, power domains and possibly even GPIOs, if an external +transceiver is used. Look at other boards that use the same SoC, for clues as to +what is needed.
+Thirdly, when added tags, put them in a xxx-u-boot.dtsi file, where xxx is your
%s/added/adding/ ?
What is a tag meant to be here? Tags do not exist in the driver model up to now. This really needs a link to a chapter describing what a tag is.
+board name, or SoC name. There may already be a file for your SoC which contains +what you need. U-Boot automatically includes these files: see :ref:`dttweaks`.
+Here are some things you might need to consider:
+1. The serial driver itself needs to be present before relocation, so that the
Is this meant to be the first item of an numbered list? If so, please fix the indentation. Please, check the output of 'make htmldocs' for correct formatting.
Best regards
Heinrich
+U-Boot banner appears. Make sure it has a u-boot,pre-reloc tag in the device +tree, so that the serial driver is bound when U-Boot starts.
+For example, on iMX8::
- lpuart3: serial@5a090000 {
compatible = "fsl,imx8qm-lpuart";...- };
+put this in your xxx-u-boot.dtsi file::
- &lpuart3 {
u-boot,dm-pre-proper;- };
+2. If your serial port requires a particular pinmux configuration, you may need +a pinctrl driver. This needs to have a u-boot,pre-reloc tag also. Take care that +any subnodes have the same tag, if they are needed to make the correct pinctrl +available.
+For example, on RK3288, the UART2 uses uart2_xfer::
- uart2: serial@ff690000 {
...pinctrl-0 = <&uart2_xfer>;- };
+which is defined as follows::
- pinctrl: pinctrl {
compatible = "rockchip,rk3228-pinctrl";uart2: uart2 {uart2_xfer: uart2-xfer {rockchip,pins = <1 RK_PC2 RK_FUNC_2 &pcfg_pull_up>,<1 RK_PC3 RK_FUNC_2 &pcfg_pull_none>;};...- };
+This means you must make the uart2-xfer node available as well as all its +parents, so put this in your xxx-u-boot.dtsi file::
- &pinctrl {
u-boot,dm-pre-reloc;- };
- &uart2 {
u-boot,dm-pre-reloc;- };
- &uart2_xfer {
u-boot,dm-pre-reloc;- };
+3. The same applies to power domains. For example, if a particular power domain +must be enabled for the serial port to work, you need to ensure it is available +before relocation:
+For example, on iMX8, put this in your xxx-u-boot.dtsi file::
- &pd_dma {
u-boot,dm-pre-proper;- };
- &pd_dma_lpuart3 {
u-boot,dm-pre-proper;- };
+4. The same applies to clocks, in the same way. Make sure that when your driver +requests a clock, typically with clk_get_by_index(), it is available.
+Generally a failure to find a required device will cause an error which you can +catch, if you have the debug UART working. U-Boot outputs serial data to the +debug UART until the point where the real serial driver takes over. This point +is marked by gd->flags having the GD_FLG_SERIAL_READY flag set. This change +happens in serial_init() in serial-uclass.c so until that point the debug UART +is used. You can see the relevant code in putc() +, for example::
- /* if we don't have a console yet, use the debug UART */
- if (IS_ENABLED(CONFIG_DEBUG_UART) && !(gd->flags & GD_FLG_SERIAL_READY)) {
printch(c);return;- }
- ... carries on to use the console / serial driver
+Note that in device_probe() the call to pinctrl_select_state() silently fails +if the pinctrl driver fails. You can add a temporary check there if needed.
+Why do we have all these tags? The problem is that before relocation we don't +want to bind all the drivers since memory is limited and the CPU may be running +at a slow speed. So many boards will fail to boot without this optimisation, or +may take a long time to start up (e.g. hundreds of milliseconds). The tags tell +U-Boot which drivers to bind.
+The good news is that this problem is normally solved by the SoC, so that any +boards that use it will work as normal. But in some cases there are multiple +UARTs or multiple pinmux options, which means that each board may need to do +some customisation.
+Serial in SPL +-------------
+A similar process is needed in SPL, but in this case the u-boot,dm-spl or +u-boot,dm-tpl tags are used. Add these in the same way as above, to ensure that +the SPL device tree contains the required nodes (see spl/u-boot-spl.dtb for +what it actually contains).
+Removing old code +-----------------
+In some cases there may be initialisation code that is no-longer needed when +driver model is used, such as setting up the pin muxing, or enabling a clock. +Be sure to remove this.
+Example patch +-------------
+See this serial_patch_ for iMX7.
+.. _serial_patch: https://patchwork.ozlabs.org/project/uboot/patch/20220314232406.1945308-1-fe...