This is not used since time out of mind.
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass sjg@chromium.org ---
(no changes since v1)
drivers/mtd/nand/raw/Makefile | 1 - drivers/mtd/nand/raw/kb9202_nand.c | 134 ----------------------------- 2 files changed, 135 deletions(-) delete mode 100644 drivers/mtd/nand/raw/kb9202_nand.c
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile index f004eb39f3b..c25acb11804 100644 --- a/drivers/mtd/nand/raw/Makefile +++ b/drivers/mtd/nand/raw/Makefile @@ -56,7 +56,6 @@ obj-$(CONFIG_NAND_DENALI) += denali.o obj-$(CONFIG_NAND_DENALI_DT) += denali_dt.o obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_nand.o -obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o obj-$(CONFIG_NAND_KMETER1) += kmeter1_nand.o obj-$(CONFIG_NAND_LPC32XX_MLC) += lpc32xx_nand_mlc.o diff --git a/drivers/mtd/nand/raw/kb9202_nand.c b/drivers/mtd/nand/raw/kb9202_nand.c deleted file mode 100644 index 9d26532c780..00000000000 --- a/drivers/mtd/nand/raw/kb9202_nand.c +++ /dev/null @@ -1,134 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2006 - * KwikByte kb9200_dev@kwikbyte.com - * - * (C) Copyright 2009 - * Matthias Kaehlcke matthias@kaehlcke.net - */ - -#include <common.h> -#include <linux/mtd/rawnand.h> -#include <asm/io.h> -#include <asm/arch/AT91RM9200.h> -#include <asm/arch/hardware.h> - -#include <nand.h> - -/* - * hardware specific access to control-lines - */ - -#define MASK_ALE (1 << 22) /* our ALE is A22 */ -#define MASK_CLE (1 << 21) /* our CLE is A21 */ - -#define KB9202_NAND_NCE (1 << 28) /* EN* on D28 */ -#define KB9202_NAND_BUSY (1 << 29) /* RB* on D29 */ - -#define KB9202_SMC2_NWS (1 << 2) -#define KB9202_SMC2_TDF (1 << 8) -#define KB9202_SMC2_RWSETUP (1 << 24) -#define KB9202_SMC2_RWHOLD (1 << 29) - -/* - * Board-specific function to access device control signals - */ -static void kb9202_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) -{ - struct nand_chip *this = mtd_to_nand(mtd); - - if (ctrl & NAND_CTRL_CHANGE) { - ulong IO_ADDR_W = (ulong) this->IO_ADDR_W; - - /* clear ALE and CLE bits */ - IO_ADDR_W &= ~(MASK_ALE | MASK_CLE); - - if (ctrl & NAND_CLE) - IO_ADDR_W |= MASK_CLE; - - if (ctrl & NAND_ALE) - IO_ADDR_W |= MASK_ALE; - - this->IO_ADDR_W = (void *) IO_ADDR_W; - - if (ctrl & NAND_NCE) - writel(KB9202_NAND_NCE, AT91C_PIOC_CODR); - else - writel(KB9202_NAND_NCE, AT91C_PIOC_SODR); - } - - if (cmd != NAND_CMD_NONE) - writeb(cmd, this->IO_ADDR_W); -} - - -/* - * Board-specific function to access the device ready signal. - */ -static int kb9202_nand_ready(struct mtd_info *mtd) -{ - return readl(AT91C_PIOC_PDSR) & KB9202_NAND_BUSY; -} - - -/* - * Board-specific NAND init. Copied from include/linux/mtd/nand.h for reference. - * - * struct nand_chip - NAND Private Flash Chip Data - * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device - * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device - * @hwcontrol: [BOARDSPECIFIC] hardwarespecific function for accesing control-lines - * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line - * If set to NULL no access to ready/busy is available and the ready/busy information - * is read from the chip status register - * @enable_hwecc: [BOARDSPECIFIC] function to enable (reset) hardware ecc generator. Must only - * be provided if a hardware ECC is available - * @eccmode: [BOARDSPECIFIC] mode of ecc, see defines - * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR) - * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about - * special functionality. See the defines for further explanation -*/ -/* - * This routine initializes controller and GPIOs. - */ -int board_nand_init(struct nand_chip *nand) -{ - unsigned int value; - - nand->ecc.mode = NAND_ECC_SOFT; - nand->cmd_ctrl = kb9202_nand_hwcontrol; - nand->dev_ready = kb9202_nand_ready; - - /* in case running outside of bootloader */ - writel(1 << AT91C_ID_PIOC, AT91C_PMC_PCER); - - /* setup nand flash access (allow ample margin) */ - /* 4 wait states, 1 setup, 1 hold, 1 float for 8-bit device */ - writel(AT91C_SMC2_WSEN | KB9202_SMC2_NWS | KB9202_SMC2_TDF | - AT91C_SMC2_DBW_8 | KB9202_SMC2_RWSETUP | KB9202_SMC2_RWHOLD, - AT91C_SMC_CSR3); - - /* enable internal NAND controller */ - value = readl(AT91C_EBI_CSA); - value |= AT91C_EBI_CS3A_SMC_SmartMedia; - writel(value, AT91C_EBI_CSA); - - /* enable SMOE/SMWE */ - writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_ASR); - writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_PDR); - writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_OER); - - /* set NCE to high */ - writel(KB9202_NAND_NCE, AT91C_PIOC_SODR); - - /* disable output on pin connected to the busy line of the NAND */ - writel(KB9202_NAND_BUSY, AT91C_PIOC_ODR); - - /* enable the PIO to control NCE and BUSY */ - writel(KB9202_NAND_NCE | KB9202_NAND_BUSY, AT91C_PIOC_PER); - - /* enable output for NCE */ - writel(KB9202_NAND_NCE, AT91C_PIOC_OER); - - return (0); -}