On 16 June 2015 at 14:48, Heiko Schocher denx hs@denx.de wrote:
Hello Jagan,
Am 16.06.2015 um 10:52 schrieb Jagan Teki:
Hi Heiko,
On 16 June 2015 at 14:13, Heiko Schocher denx hs@denx.de wrote:
Hello Jagan,
Am 16.06.2015 um 10:04 schrieb Jagan Teki:
Hi Heiko,
On 20 May 2015 at 12:16, Heiko Schocher hs@denx.de wrote:
Hello Jagan,
Am 19.05.2015 22:09, schrieb Jagan Teki:
Hi Heiko,
I have tested this sf-mtd stuff, please see below and enabled prints in all the func calls.
Thanks for testing!
zynq-uboot> mtdparts add nor0 0x10000@0x0 env mtdparts variable not set, see 'help mtdparts' zynq-uboot> mtdparts
device nor0 <zynq-sf.0>, # parts = 1 #: name size offset mask_flags 0: env 0x00010000 0x00000000 0
active partition: nor0,0 - (env) 0x00010000 @ 0x00000000
defaults: mtdids : nor0=zynq-sf.0 mtdparts: none zynq-uboot> sf erase env 0x10000 spi_flash_erase spi_flash_cmd_erase_ops SF: erase d8 0 0 0 (0) SF: 65536 bytes @ 0x0 Erased: OK zynq-uboot> mw.b 0x100 0x44 0x10000 zynq-uboot> sf write 0x100 env device 0 offset 0x0, size 0x10000 spi_flash_cmd_write_ops SF: 65536 bytes @ 0x0 Written: OK zynq-uboot> sf read 0x40000 env device 0 offset 0x0, size 0x10000 spi_flash_cmd_read_ops off = 0x10000, len = 0 SF: 65536 bytes @ 0x0 Read: OK zynq-uboot> cmp.b 0x100 0x40000 0x10000 Total of 65536 byte(s) were the same
Looks good ...
I wonder none of the sf_mtd_info._* getting called, why?
Hmm.. good question .. you use the "sf ..." commands, they do not use the mtd interface, right?
I'm fine with the testing, but mtd code in sf seems used only for in UBI only.
a fast "grep mtd_read" in the u-boot source shows, that yaffs2 also uses mtd_read ... I did no yaffs2 test, but I think, yaffs2 can be used also with spi flashes now ... if this is wise, I don;t know ...
I tested with UBI on a spi flash, and that works ... in the same fashion it currently does on nand for example ...
I wouldn't see this is a better approach where mtd code is considered as to be unknown thing for sf.
I do not understand you here complete ...
drivers/mtd/spi/sf_mtd.c
adds just spi flash specific functions to integrate spi flashes into mtd ... and mtd users can then read/write/erase with the mtd_* functions ...
Maybe someone has time to convert common/sf.c to use them?
So, the final question is, can this patches go into mainline?
The only point I'm concerned here is If I need to use sf with mtd support without using ubifs or any flash filesystem, the code in sf_mtd.c ops becomes unused.
Why you want to enable mtd support for sf, if you not use it? do not define CONFIG_SPI_FLASH_MTD in this case?
Suppose I need sf-mtd and enabled CONFIG_SPI_FLASH_MTD so when I did it from sf_cmd the code in sf-mtd.c is never been used for erase/read/write. Is that true right?
This seems to be a code size increasing factor which is obviously not a good point for bootloader atleast for u-boot, what do you think?
I agreed your concerned for someone may add support to common/cmd_sf.c in future, but I'm bit worried to go this.
Why? Its the same state as it is in the nand subsystem ...
Agreed but until unless if you have filesystem link to cmd_sf to partitioning.
I tested this functions with using UBI on the SPI NOR on the aristainetos and aristianetos2 boards... I added for example in
diff --git a/drivers/mtd/spi/sf_mtd.c b/drivers/mtd/spi/sf_mtd.c index 0b9cb62..6063ed7 100644 --- a/drivers/mtd/spi/sf_mtd.c +++ b/drivers/mtd/spi/sf_mtd.c @@ -39,6 +40,7 @@ static int spi_flash_mtd_read(struct mtd_info *mtd, loff_t from, size_t len, struct spi_flash *flash = mtd->priv; int err;
+printf("%s ****\n", __func__); err = spi_flash_read(flash, from, len, buf); if (!err) *retlen = len;
and see:
=> sf probe SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB => mtdparts
device nor0 <spi3.1>, # parts = 4 #: name size offset mask_flags 0: u-boot 0x000d0000 0x00000000 0 1: env 0x00010000 0x000d0000 0 2: env-red 0x00010000 0x000e0000 0 3: rescue-system 0x00f10000 0x000f0000 0
device nand0 <gpmi-nand>, # parts = 1 #: name size offset mask_flags 0: ubi 0x40000000 0x00000000 0
active partition: nor0,0 - (u-boot) 0x000d0000 @ 0x00000000
defaults: mtdids : none mtdparts: none => ubi part rescue-system UBI: default fastmap pool size: 10 UBI: default fastmap WL pool size: 25 UBI: attaching mtd2 to ubi0 UBI DBG gen (pid 1): sizeof(struct ubi_ainf_peb) 48 UBI DBG gen (pid 1): sizeof(struct ubi_wl_entry) 20 UBI DBG gen (pid 1): min_io_size 1 UBI DBG gen (pid 1): max_write_size 256 UBI DBG gen (pid 1): hdrs_min_io_size 1 UBI DBG gen (pid 1): ec_hdr_alsize 64 UBI DBG gen (pid 1): vid_hdr_alsize 64 UBI DBG gen (pid 1): vid_hdr_offset 64 UBI DBG gen (pid 1): vid_hdr_aloffset 64 UBI DBG gen (pid 1): vid_hdr_shift 0 UBI DBG gen (pid 1): leb_start 128 UBI DBG gen (pid 1): max_erroneous 24 UBI DBG gen (pid 1): process PEB 0 UBI DBG bld (pid 1): scan PEB 0 UBI DBG io (pid 1): read EC header from PEB 0 UBI DBG io (pid 1): read 64 bytes from PEB 0:0 spi_flash_mtd_read **** UBI DBG io (pid 1): read VID header from PEB 0 UBI DBG io (pid 1): read 64 bytes from PEB 0:64 spi_flash_mtd_read **** [...]
UBI uses the MTD layer ... the sf command not ... Hope this helps?
bye, Heiko
On 27 April 2015 at 11:12, Heiko Schocher hs@denx.de wrote: > > > > From: Daniel Schwierzeck daniel.schwierzeck@gmail.com > > add MTD layer driver for spi, original patch from: > > > > http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493... > > changes from Heiko Schocher against this patch: > - remove compile error if not defining CONFIG_SPI_FLASH_MTD: > > LD drivers/mtd/spi/built-in.o > drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister': > /home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple > definition of `spi_flash_mtd_unregister' > > > > drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: > first defined here > drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister': > /home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple > definition of `spi_flash_mtd_unregister' > > > > drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: > first defined here > make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1 > make: *** [drivers/mtd/spi] Fehler 2 > > - add a README entry. > - add correct writebufsize, to fit with Linux v3.14 > MTD, UBI/UBIFS sync. > > Signed-off-by: Daniel Schwierzeck daniel.schwierzeck@gmail.com > Signed-off-by: Heiko Schocher hs@denx.de > > --- > > Changes in v6: None > Changes in v2: > - add comment from Daniel Schwierzeck: > fix compile error from original patch with > "static inline" rather than "static __maybe_unused" > Series-changes: 3 > - rebase with d6c1ffc7d23f4fe4ae8c91101861055b8e1501b6 > Series-changes: 4 > - rebased against 385a08a60f042061b004642d6b9bb6cfb794ad5a > Series-changes: 5 > - no changes > Series-changes: 6 > - add comments from Jagan Teki: > move code, which checks if flash pointer is used > into a new patch. > - use #ifdef in Code > - call mtd register before the spi_release_bus > > README | 3 ++ > common/cmd_sf.c | 2 - > drivers/mtd/spi/Makefile | 1 + > drivers/mtd/spi/sf_internal.h | 5 ++ > drivers/mtd/spi/sf_mtd.c | 104 > ++++++++++++++++++++++++++++++++++++++++++ > drivers/mtd/spi/sf_probe.c | 10 ++-- > 6 files changed, 119 insertions(+), 6 deletions(-) > create mode 100644 drivers/mtd/spi/sf_mtd.c > > diff --git a/README b/README > index fc1fd52..36f6fc9 100644 > --- a/README > +++ b/README > @@ -3097,6 +3097,9 @@ CBFS (Coreboot Filesystem) support > operation will not execute. The only way to exit > this > hardware-protected mode is to drive W#/VPP HIGH. > > + CONFIG_SPI_FLASH_MTD > + add MTD translation layer driver. > + > - SystemACE Support: > CONFIG_SYSTEMACE > > diff --git a/common/cmd_sf.c b/common/cmd_sf.c > index 6aabf39..0250011 100644 > --- a/common/cmd_sf.c > +++ b/common/cmd_sf.c > @@ -139,8 +139,6 @@ static int do_spi_flash_probe(int argc, char * > const > argv[]) > return 1; > } > > - if (flash) > - spi_flash_free(flash); > flash = new; > #endif > > diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile > index c61b784e..f8580cd 100644 > --- a/drivers/mtd/spi/Makefile > +++ b/drivers/mtd/spi/Makefile > @@ -17,5 +17,6 @@ obj-$(CONFIG_SPI_FLASH) += sf_probe.o > #endif > obj-$(CONFIG_CMD_SF) += sf.o > obj-$(CONFIG_SPI_FLASH) += sf_ops.o sf_params.o > +obj-$(CONFIG_SPI_FLASH_MTD) += sf_mtd.o > obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o > obj-$(CONFIG_SPI_M95XXX) += eeprom_m95xxx.o > diff --git a/drivers/mtd/spi/sf_internal.h > b/drivers/mtd/spi/sf_internal.h > index 785f7a9..8a2eb6e 100644 > --- a/drivers/mtd/spi/sf_internal.h > +++ b/drivers/mtd/spi/sf_internal.h > @@ -221,4 +221,9 @@ int spi_flash_read_common(struct spi_flash > *flash, > const u8 *cmd, > int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset, > size_t len, void *data); > > +#ifdef CONFIG_SPI_FLASH_MTD > +int spi_flash_mtd_register(struct spi_flash *flash); > +void spi_flash_mtd_unregister(void); > +#endif > + > #endif /* _SF_INTERNAL_H_ */ > diff --git a/drivers/mtd/spi/sf_mtd.c b/drivers/mtd/spi/sf_mtd.c > new file mode 100644 > index 0000000..0b9cb62 > --- /dev/null > +++ b/drivers/mtd/spi/sf_mtd.c > @@ -0,0 +1,104 @@ > +/* > + * Copyright (C) 2012-2014 Daniel Schwierzeck, > daniel.schwierzeck@gmail.com > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include <common.h> > +#include <malloc.h> > +#include <asm/errno.h> > +#include <linux/mtd/mtd.h> > +#include <spi_flash.h> > + > +static struct mtd_info sf_mtd_info; > +static char sf_mtd_name[8]; > + > +static int spi_flash_mtd_erase(struct mtd_info *mtd, struct > erase_info > *instr) > +{ > + struct spi_flash *flash = mtd->priv; > + int err; > + > + instr->state = MTD_ERASING; > + > + err = spi_flash_erase(flash, instr->addr, instr->len); > + if (err) { > + instr->state = MTD_ERASE_FAILED; > + instr->fail_addr = MTD_FAIL_ADDR_UNKNOWN; > + return -EIO; > + } > + > + instr->state = MTD_ERASE_DONE; > + mtd_erase_callback(instr); > + > + return 0; > +} > + > +static int spi_flash_mtd_read(struct mtd_info *mtd, loff_t from, > size_t > len, > + size_t *retlen, u_char *buf) > +{ > + struct spi_flash *flash = mtd->priv; > + int err; > + > + err = spi_flash_read(flash, from, len, buf); > + if (!err) > + *retlen = len; > + > + return err; > +} > + > +static int spi_flash_mtd_write(struct mtd_info *mtd, loff_t to, > size_t > len, > + size_t *retlen, const u_char *buf) > +{ > + struct spi_flash *flash = mtd->priv; > + int err; > + > + err = spi_flash_write(flash, to, len, buf); > + if (!err) > + *retlen = len; > + > + return err; > +} > + > +static void spi_flash_mtd_sync(struct mtd_info *mtd) > +{ > +} > + > +static int spi_flash_mtd_number(void) > +{ > +#ifdef CONFIG_SYS_MAX_FLASH_BANKS > + return CONFIG_SYS_MAX_FLASH_BANKS; > +#else > + return 0; > +#endif > +} > + > +int spi_flash_mtd_register(struct spi_flash *flash) > +{ > + memset(&sf_mtd_info, 0, sizeof(sf_mtd_info)); > + sprintf(sf_mtd_name, "nor%d", spi_flash_mtd_number()); > + > + sf_mtd_info.name = sf_mtd_name; > + sf_mtd_info.type = MTD_NORFLASH; > + sf_mtd_info.flags = MTD_CAP_NORFLASH; > + sf_mtd_info.writesize = 1; > + sf_mtd_info.writebufsize = flash->page_size; > + > + sf_mtd_info._erase = spi_flash_mtd_erase; > + sf_mtd_info._read = spi_flash_mtd_read; > + sf_mtd_info._write = spi_flash_mtd_write; > + sf_mtd_info._sync = spi_flash_mtd_sync;
Even if I remove this every thing as usual, like "sf erase" will call from cmd_sf there it calls mtd_arg_off_size, to detected off and size from partition and after sf_flash will call erase ops from sf_ops.c.
As it's a mtd call, I thought sf_mtd_into._erase will intern calls erase ops from sf_ops.c What is this behavior could you please help me?
> + > + sf_mtd_info.size = flash->size; > + sf_mtd_info.priv = flash; > + > + /* Only uniform flash devices for now */ > + sf_mtd_info.numeraseregions = 0; > + sf_mtd_info.erasesize = flash->sector_size; > + > + return add_mtd_device(&sf_mtd_info); > +} > + > +void spi_flash_mtd_unregister(void) > +{ > + del_mtd_device(&sf_mtd_info); > +} > diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c > index d19138d..2342972 100644 > --- a/drivers/mtd/spi/sf_probe.c > +++ b/drivers/mtd/spi/sf_probe.c > @@ -397,10 +397,9 @@ int spi_flash_probe_slave(struct spi_slave *spi, > struct spi_flash *flash) > if (spi_enable_wp_pin(flash)) > puts("Enable WP pin failed\n"); > > - /* Release spi bus */ > - spi_release_bus(spi); > - > - return 0; > +#ifdef CONFIG_SPI_FLASH_MTD > + ret = spi_flash_mtd_register(flash); > +#endif > > err_read_id: > spi_release_bus(spi); > @@ -450,6 +449,9 @@ struct spi_flash *spi_flash_probe_fdt(const void > *blob, int slave_node, > > void spi_flash_free(struct spi_flash *flash) > { > +#ifdef CONFIG_SPI_FLASH_MTD > + spi_flash_mtd_unregister(); > +#endif > spi_free_slave(flash->spi); > free(flash); > } > -- > 2.1.0
thanks!