Hi Tom,
The following changes since commit a7f99bf139b3aaa0d5494693fd0395084355e41a:
arm: Fix _start for CONFIG_SYS_DV_NOR_BOOT_CFG (2014-09-11 18:04:39 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-arm master
for you to fetch changes up to c292adae170fa8c27dca75963bdb0a9afc640e57:
Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' (2014-09-17 23:35:34 +0200)
NOTE: two boards are broken by this PR, trimslice and cm_fx6, due to commits in the imx tree depending on some commits in the spi tree. Once both this PR and the spi commits are in, both boards should build fine again.
----------------------------------------------------------------
Albert ARIBAUD (1): Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Fabio Estevam (9): net: fec_mxc: Adjust RX DMA alignment for mx6solox net: fec_mxc: Poll FEC_TBD_READY after polling TDAR tools: imximage: Fix the maximum DCD size for mx53/mx6 mx6dlsabresd: Use its own DCD table mx6qsabreauto: Remove imx6q-sabreauto.dts mx6: imx-regs: Provide a structure for GPC registers pcie_imx: Add mx6solox support mx6sxsabresd: Add PCI support README.imximage: Fix the maximum DCD size
Guillaume GARDET (1): imx: nitrogen6x: Replace 'fatload' by 'load' command in env settings to be filesystem independent
Nikita Kiryanov (16): mx6: add clock enabling functions compulab: eeprom: add support for defining eeprom i2c bus sata: dwc_ahsata: implement sata_port_status i2c: imx: add macros to setup pads for multiple SoC types arm: mx6: ddr: cleanup arm: mx6: ddr: do not write into reserved bit arm: mx6: ddr: configure MMDC for slow_pd arm: mx6: ddr: fix cs0_end calculation arm: mx6: add get_cpu_type() arm: mx6: add support for Compulab cm-fx6 CoM arm: mx6: cm_fx6: add nand support arm: mx6: cm_fx6: add ethernet support arm: mx6: cm_fx6: add usb support arm: mx6: cm_fx6: add i2c support arm: mx6: cm_fx6: use eeprom arm: mx6: cm_fx6: add sata support
Nikolay Dimitrov (1): mx6: Fix ECSPI typo in soc_boot_modes
Stefan Agner (2): arm: vf610: lpuart: fix status register handling arm: vf610: lpuart: disable FIFO on initializaton
Stefano Babic (1): imx: Fix build of mx6sxsabresd
Thierry Reding (1): imx: ventana: Avoid undefined behaviour
Tim Harvey (6): imx: ventana: updated notes regarding NAND boot errata imx: ventana: base SPL MMDC calibration on width and size not board imx: ventana: add GW5520 support imx: ventana: added cputype env var pci: add support for board_pci_fixup_dev function imx: ventana: add pci fixup for PLX PEX860x switch GPIO
Ye.Li (4): iMX6: Disable the L2 before chaning the PL310 latency imximage: Fix imximage IVT bug for EIM-NOR boot imx: mx6q/dlarm2: Change to use generic board imx: mx6slevk: Change to use generic board
arch/arm/Kconfig | 4 + arch/arm/cpu/armv7/mx6/clock.c | 107 +++++- arch/arm/cpu/armv7/mx6/ddr.c | 277 ++++++++-------- arch/arm/cpu/armv7/mx6/soc.c | 11 +- arch/arm/dts/Makefile | 1 - arch/arm/dts/imx6q-sabreauto.dts | 13 - arch/arm/include/asm/arch-mx6/clock.h | 5 + arch/arm/include/asm/arch-mx6/imx-regs.h | 13 + arch/arm/include/asm/arch-mx6/iomux.h | 9 + arch/arm/include/asm/arch-mx6/sys_proto.h | 5 +- arch/arm/include/asm/imx-common/mxc_i2c.h | 33 ++ board/compulab/cm_fx6/Kconfig | 23 ++ board/compulab/cm_fx6/MAINTAINERS | 6 + board/compulab/cm_fx6/Makefile | 12 + board/compulab/cm_fx6/cm_fx6.c | 483 ++++++++++++++++++++++++++++ board/compulab/cm_fx6/common.c | 84 +++++ board/compulab/cm_fx6/common.h | 37 +++ board/compulab/cm_fx6/imximage.cfg | 8 + board/compulab/cm_fx6/spl.c | 366 +++++++++++++++++++++ board/compulab/common/eeprom.c | 13 +- board/freescale/mx6sabresd/mx6dlsabresd.cfg | 131 ++++++++ board/gateworks/gw_ventana/eeprom.c | 3 + board/gateworks/gw_ventana/gsc.c | 4 + board/gateworks/gw_ventana/gw_ventana.c | 118 ++++++- board/gateworks/gw_ventana/gw_ventana_spl.c | 189 ++++++----- board/gateworks/gw_ventana/ventana_eeprom.h | 1 + configs/cm_fx6_defconfig | 4 + configs/mx6dlsabresd_defconfig | 2 +- doc/README.imximage | 2 +- drivers/block/dwc_ahsata.c | 17 + drivers/net/fec_mxc.c | 42 ++- drivers/pci/pci.c | 4 + drivers/pci/pcie_imx.c | 40 ++- drivers/serial/serial_lpuart.c | 19 +- include/configs/cm_fx6.h | 290 +++++++++++++++++ include/configs/cm_t335.h | 1 + include/configs/cm_t35.h | 1 + include/configs/cm_t54.h | 1 + include/configs/gw_ventana.h | 1 + include/configs/mx6qarm2.h | 2 + include/configs/mx6qsabreauto.h | 3 - include/configs/mx6slevk.h | 2 + include/configs/mx6sxsabresd.h | 10 + include/configs/nitrogen6x.h | 6 +- include/pci.h | 7 + include/sata.h | 1 + tools/imximage.c | 7 + tools/imximage.h | 2 +- 48 files changed, 2140 insertions(+), 280 deletions(-) delete mode 100644 arch/arm/dts/imx6q-sabreauto.dts create mode 100644 board/compulab/cm_fx6/Kconfig create mode 100644 board/compulab/cm_fx6/MAINTAINERS create mode 100644 board/compulab/cm_fx6/Makefile create mode 100644 board/compulab/cm_fx6/cm_fx6.c create mode 100644 board/compulab/cm_fx6/common.c create mode 100644 board/compulab/cm_fx6/common.h create mode 100644 board/compulab/cm_fx6/imximage.cfg create mode 100644 board/compulab/cm_fx6/spl.c create mode 100644 board/freescale/mx6sabresd/mx6dlsabresd.cfg create mode 100644 configs/cm_fx6_defconfig create mode 100644 include/configs/cm_fx6.h
Amicalement,