From: Jagan Teki jagan@amarulasolutions.com
- Removed non-fdt code (becuase which has dt support) - Remove mx6sabresd_spl_defconfig - Re-arrange the header includes and removed unneeded includes. - Move the SPL code in #ifdef CONFIG_SPL_BUILD area.
Cc: Stefano Babic sbabic@denx.de Cc: Fabio Estevam fabio.estevam@nxp.com Cc: Michael Trimarchi michael@amarulasolutions.com Signed-off-by: Jagan Teki jagan@amarulasolutions.com --- board/freescale/mx6sabresd/MAINTAINERS | 1 - board/freescale/mx6sabresd/mx6sabresd.c | 396 +++++--------------------------- configs/mx6sabresd_spl_defconfig | 54 ----- include/configs/mx6sabresd.h | 23 -- 4 files changed, 63 insertions(+), 411 deletions(-) delete mode 100644 configs/mx6sabresd_spl_defconfig
diff --git a/board/freescale/mx6sabresd/MAINTAINERS b/board/freescale/mx6sabresd/MAINTAINERS index 227c6dd..86e62e9 100644 --- a/board/freescale/mx6sabresd/MAINTAINERS +++ b/board/freescale/mx6sabresd/MAINTAINERS @@ -5,5 +5,4 @@ F: board/freescale/mx6sabresd/ F: include/configs/mx6sabresd.h F: configs/imx6dl_sabresd_defconfig F: configs/imx6q_sabresd_defconfig -F: configs/mx6sabresd_spl_defconfig F: configs/imx6qdl_sabresd_spl_defconfig diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 7c28cc7..18c5d5d 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -6,30 +6,24 @@ * SPDX-License-Identifier: GPL-2.0+ */
+#include <common.h> +#include <miiphy.h> +#include <mmc.h> +#include <fsl_esdhc.h> + +#include <asm/io.h> +#include <asm/gpio.h> +#include <linux/sizes.h> + #include <asm/arch/clock.h> -#include <asm/arch/imx-regs.h> +#include <asm/arch/crm_regs.h> #include <asm/arch/iomux.h> +#include <asm/arch/mxc_hdmi.h> #include <asm/arch/mx6-pins.h> -#include <linux/errno.h> -#include <asm/gpio.h> -#include <asm/imx-common/mxc_i2c.h> -#include <asm/imx-common/iomux-v3.h> +#include <asm/arch/sys_proto.h> #include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/iomux-v3.h> #include <asm/imx-common/video.h> -#include <mmc.h> -#include <fsl_esdhc.h> -#include <miiphy.h> -#include <netdev.h> -#include <asm/arch/mxc_hdmi.h> -#include <asm/arch/crm_regs.h> -#include <asm/io.h> -#include <asm/arch/sys_proto.h> -#include <i2c.h> -#include <power/pmic.h> -#include <power/pfuze100_pmic.h> -#include "../common/pfuze.h" -#include <asm/arch/mx6-ddr.h> -#include <usb.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -37,28 +31,9 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ - PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ - PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ - PAD_CTL_ODE | PAD_CTL_SRE_FAST) - -#define I2C_PMIC 1 - -#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL) - -#define DISP0_PWR_EN IMX_GPIO_NR(1, 21) - -#define KEY_VOL_UP IMX_GPIO_NR(1, 4) - int dram_init(void) { gd->ram_size = imx_ddr_size(); @@ -70,80 +45,6 @@ static iomux_v3_cfg_t const uart1_pads[] = { MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), };
-#ifndef CONFIG_OF_CONTROL -static iomux_v3_cfg_t const enet_pads[] = { - MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), - /* AR8031 PHY Reset */ - MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static void setup_iomux_enet(void) -{ - imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); - - /* Reset AR8031 PHY */ - gpio_direction_output(IMX_GPIO_NR(1, 25) , 0); - mdelay(10); - gpio_set_value(IMX_GPIO_NR(1, 25), 1); - udelay(100); -} -#endif - -static iomux_v3_cfg_t const usdhc2_pads[] = { - MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_D4__SD2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_D5__SD2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_D6__SD2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_D7__SD2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ -}; - -static iomux_v3_cfg_t const usdhc3_pads[] = { - MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ -}; - -static iomux_v3_cfg_t const usdhc4_pads[] = { - MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), -}; - static iomux_v3_cfg_t const ecspi1_pads[] = { MX6_PAD_KEY_COL0__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_KEY_COL1__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), @@ -189,12 +90,11 @@ static iomux_v3_cfg_t const bl_pads[] = {
static void enable_backlight(void) { - imx_iomux_v3_setup_multiple_pads(bl_pads, ARRAY_SIZE(bl_pads)); - -#ifdef CONFIG_OF_CONTROL struct gpio_desc backlight; int ret;
+ imx_iomux_v3_setup_multiple_pads(bl_pads, ARRAY_SIZE(bl_pads)); + /* Set Brightness to high */ ret = dm_gpio_lookup_name("GPIO1_21", &backlight); if (ret) { @@ -210,9 +110,6 @@ static void enable_backlight(void)
dm_gpio_set_dir_flags(&backlight, GPIOD_IS_OUT); dm_gpio_set_value(&backlight, 1); -#else - gpio_direction_output(DISP0_PWR_EN, 1); -#endif }
static void enable_rgb(struct display_info_t const *dev) @@ -226,27 +123,11 @@ static void enable_lvds(struct display_info_t const *dev) enable_backlight(); }
-#ifndef CONFIG_DM_I2C -static struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD, - .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD, - .gp = IMX_GPIO_NR(4, 12) - }, - .sda = { - .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD, - .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD, - .gp = IMX_GPIO_NR(4, 13) - } -}; -#endif - static void setup_spi(void) { imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); }
-#ifndef CONFIG_OF_CONTROL iomux_v3_cfg_t const pcie_pads[] = { MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), /* POWER */ MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), /* RESET */ @@ -256,7 +137,6 @@ static void setup_pcie(void) { imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads)); } -#endif
iomux_v3_cfg_t const di0_pads[] = { MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK, /* DISP0_CLK */ @@ -269,90 +149,6 @@ static void setup_iomux_uart(void) imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); }
-#if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_OF_CONTROL) -struct fsl_esdhc_cfg usdhc_cfg[3] = { - {USDHC2_BASE_ADDR}, - {USDHC3_BASE_ADDR}, - {USDHC4_BASE_ADDR}, -}; - -#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2) -#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0) - -int board_mmc_get_env_dev(int devno) -{ - return devno - 1; -} - -int board_mmc_getcd(struct mmc *mmc) -{ - struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; - int ret = 0; - - switch (cfg->esdhc_base) { - case USDHC2_BASE_ADDR: - ret = !gpio_get_value(USDHC2_CD_GPIO); - break; - case USDHC3_BASE_ADDR: - ret = !gpio_get_value(USDHC3_CD_GPIO); - break; - case USDHC4_BASE_ADDR: - ret = 1; /* eMMC/uSDHC4 is always present */ - break; - } - - return ret; -} - -#ifndef CONFIG_FSL_ESDHC -int board_mmc_init(bd_t *bis) -{ - int ret; - int i; - - /* - * According to the board_mmc_init() the following map is done: - * (U-Boot device node) (Physical Port) - * mmc0 SD2 - * mmc1 SD3 - * mmc2 eMMC - */ - for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { - switch (i) { - case 0: - imx_iomux_v3_setup_multiple_pads( - usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); - gpio_direction_input(USDHC2_CD_GPIO); - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); - break; - case 1: - imx_iomux_v3_setup_multiple_pads( - usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); - gpio_direction_input(USDHC3_CD_GPIO); - usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - break; - case 2: - imx_iomux_v3_setup_multiple_pads( - usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); - usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); - break; - default: - printf("Warning: you configured more USDHC controllers" - "(%d) then supported by the board (%d)\n", - i + 1, CONFIG_SYS_FSL_USDHC_NUM); - return -EINVAL; - } - - ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); - if (ret) - return ret; - } - - return 0; -} -#endif -#endif - static int ar8031_phy_fixup(struct phy_device *phydev) { unsigned short val; @@ -533,7 +329,6 @@ int overwrite_console(void) return 1; }
-#ifdef CONFIG_OF_CONTROL int imx6_pcie_toggle_power(void) { #ifdef CONFIG_PCIE_IMX_POWER_GPIO @@ -592,80 +387,6 @@ int imx6_pcie_toggle_reset(void) #endif return 0; } -#endif - -#ifndef CONFIG_OF_CONTROL -int board_eth_init(bd_t *bis) -{ - setup_iomux_enet(); - setup_pcie(); - - return cpu_eth_init(bis); -} -#endif - -#if defined(CONFIG_USB_EHCI_MX6) && !defined(CONFIG_DM_USB) -#define USB_OTHERREGS_OFFSET 0x800 -#define UCTRL_PWR_POL (1 << 9) - -static iomux_v3_cfg_t const usb_otg_pads[] = { - MX6_PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static iomux_v3_cfg_t const usb_hc1_pads[] = { - MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static void setup_usb(void) -{ - imx_iomux_v3_setup_multiple_pads(usb_otg_pads, - ARRAY_SIZE(usb_otg_pads)); - - /* - * set daisy chain for otg_pin_id on 6q. - * for 6dl, this bit is reserved - */ - imx_iomux_set_gpr_register(1, 13, 1, 0); - - imx_iomux_v3_setup_multiple_pads(usb_hc1_pads, - ARRAY_SIZE(usb_hc1_pads)); -} - -int board_ehci_hcd_init(int port) -{ - u32 *usbnc_usb_ctrl; - - if (port > 1) - return -EINVAL; - - usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + - port * 4); - - setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); - - return 0; -} - -int board_ehci_power(int port, int on) -{ - switch (port) { - case 0: - break; - case 1: - if (on) - gpio_direction_output(IMX_GPIO_NR(1, 29), 1); - else - gpio_direction_output(IMX_GPIO_NR(1, 29), 0); - break; - default: - printf("MXC USB port %d not yet supported\n", port); - return -EINVAL; - } - - return 0; -} -#endif
int board_early_init_f(void) { @@ -685,46 +406,10 @@ int board_init(void) #ifdef CONFIG_MXC_SPI setup_spi(); #endif -#ifndef CONFIG_DM_I2C - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); -#endif -#if defined(CONFIG_USB_EHCI_MX6) && !defined(CONFIG_DM_USB) - setup_usb(); -#endif - - return 0; -} - -#ifndef CONFIG_DM_PMIC -int power_init_board(void) -{ - struct pmic *p; - unsigned int reg; - int ret; - - p = pfuze_common_init(I2C_PMIC); - if (!p) - return -ENODEV; - - ret = pfuze_mode_init(p, APS_PFM); - if (ret < 0) - return ret; - - /* Increase VGEN3 from 2.5 to 2.8V */ - pmic_reg_read(p, PFUZE100_VGEN3VOL, ®); - reg &= ~LDO_VOL_MASK; - reg |= LDOB_2_80V; - pmic_reg_write(p, PFUZE100_VGEN3VOL, reg); - - /* Increase VGEN5 from 2.8 to 3V */ - pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); - reg &= ~LDO_VOL_MASK; - reg |= LDOB_3_00V; - pmic_reg_write(p, PFUZE100_VGEN5VOL, reg); + setup_pcie();
return 0; } -#endif
#ifdef CONFIG_MXC_SPI int board_spi_cs_gpio(unsigned bus, unsigned cs) @@ -776,7 +461,51 @@ int checkboard(void)
#ifdef CONFIG_FSL_ESDHC
-#if defined(CONFIG_OF_CONTROL) && !defined(CONFIG_DM_MMC) +#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NANDF_D4__SD2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NANDF_D5__SD2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NANDF_D6__SD2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NANDF_D7__SD2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ +}; + +static iomux_v3_cfg_t const usdhc3_pads[] = { + MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ +}; + +static iomux_v3_cfg_t const usdhc4_pads[] = { + MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + struct fsl_esdhc_cfg usdhc_cfg[3] = { {USDHC2_BASE_ADDR}, {USDHC3_BASE_ADDR}, @@ -810,7 +539,6 @@ int board_mmc_getcd(struct mmc *mmc)
return ret; } -#endif
int board_mmc_init(bd_t *bis) { @@ -854,6 +582,8 @@ int board_mmc_init(bd_t *bis) #endif
#ifdef CONFIG_SPL_OS_BOOT +#define KEY_VOL_UP IMX_GPIO_NR(1, 4) + int spl_start_uboot(void) { gpio_direction_input(KEY_VOL_UP); diff --git a/configs/mx6sabresd_spl_defconfig b/configs/mx6sabresd_spl_defconfig deleted file mode 100644 index bba77b6..0000000 --- a/configs/mx6sabresd_spl_defconfig +++ /dev/null @@ -1,54 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_MX6=y -CONFIG_SPL_GPIO_SUPPORT=y -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_TARGET_MX6SABRESD=y -CONFIG_SPL_MMC_SUPPORT=y -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_LIBDISK_SUPPORT=y -CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_VIDEO=y -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,SPL,MX6Q" -CONFIG_BOOTDELAY=3 -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y -CONFIG_SPL=y -CONFIG_SPL_EXT_SUPPORT=y -CONFIG_SPL_OS_BOOT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_BOOTZ=y -# CONFIG_CMD_IMLS is not set -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_I2C=y -CONFIG_CMD_USB=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_CACHE=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_EXT4=y -CONFIG_CMD_EXT4_WRITE=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y -CONFIG_SPI_FLASH=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PCI=y -CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_EHCI_MX6=y -CONFIG_USB_STORAGE=y -CONFIG_USB_GADGET=y -CONFIG_CI_UDC=y -CONFIG_USB_GADGET_DOWNLOAD=y -CONFIG_G_DNL_MANUFACTURER="FSL" -CONFIG_G_DNL_VENDOR_NUM=0x0525 -CONFIG_G_DNL_PRODUCT_NUM=0xa4a5 -# CONFIG_VIDEO_SW_CURSOR is not set -CONFIG_OF_LIBFDT=y -CONFIG_SYS_I2C_MXC=y -CONFIG_FEC_MXC=y diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h index 4f6bb1b..df3ab6e 100644 --- a/include/configs/mx6sabresd.h +++ b/include/configs/mx6sabresd.h @@ -51,34 +51,11 @@ #define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(3, 19) #endif
-/* I2C Configs */ -#if defined(CONFIG_SYS_I2C_MXC) && !defined(CONFIG_DM_I2C) -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ -#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ -#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ -#define CONFIG_SYS_I2C_SPEED 100000 -#endif - -/* PMIC */ -#ifndef CONFIG_DM_PMIC_PFUZE100 -#define CONFIG_POWER -#define CONFIG_POWER_I2C -#define CONFIG_POWER_PFUZE100 -#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 -#endif - /* USB Configs */ #ifdef CONFIG_USB_EHCI_MX6 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) - -# ifndef CONFIG_DM_USB -# define CONFIG_MXC_USB_FLAGS 0 -# define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Enabled USB controller number */ -# define CONFIG_EHCI_HCD_INIT_AFTER_RESET -# endif #endif
#endif /* __MX6QSABRESD_CONFIG_H */