For DK1/DK2 boards, check if power supply provides enough current to allow the board to boot correctly. ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2 signals. The table below shows the behavior for different range of CC1 or CC2:
range | power supply | red led | console message (Volts) | (Amps) | blinks | --------------|--------------|---------|----------------------------------- [2.10 - 1.23[ | 3 | NO | NO [1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected [0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected
If detected current is < 3A, red led is kept ON after blinking.
Signed-off-by: Patrice Chotard patrice.chotard@st.com ---
board/st/stm32mp1/stm32mp1.c | 154 ++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 153 insertions(+), 1 deletion(-)
diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c index 07d1addb2a83..253094e6b418 100644 --- a/board/st/stm32mp1/stm32mp1.c +++ b/board/st/stm32mp1/stm32mp1.c @@ -2,9 +2,10 @@ /* * Copyright (C) 2018, STMicroelectronics - All Rights Reserved */ +#include <common.h> +#include <adc.h> #include <config.h> #include <clk.h> -#include <common.h> #include <dm.h> #include <generic-phy.h> #include <led.h> @@ -27,6 +28,10 @@ DECLARE_GLOBAL_DATA_PTR; #define STM32MP_GGPIO 0x38 #define STM32MP_GGPIO_VBUS_SENSING BIT(21)
+#define USB_WARNING_LOW_THRESHOLD_UV 660000 +#define USB_START_LOW_THRESHOLD_UV 1230000 +#define USB_START_HIGH_THRESHOLD_UV 2100000 + int checkboard(void) { int ret; @@ -210,6 +215,145 @@ clk_err: return ret; }
+static int get_led(struct udevice **dev, char *led_string) +{ + char *led_name; + int ret; + + led_name = fdtdec_get_config_string(gd->fdt_blob, led_string); + if (!led_name) { + pr_debug("%s: could not find %s config string\n", + __func__, led_string); + return -ENOENT; + } + ret = led_get_by_label(led_name, dev); + if (ret) { + debug("%s: get=%d\n", __func__, ret); + return ret; + } + + return 0; +} + +static int setup_led(enum led_state_t cmd) +{ + struct udevice *dev; + int ret; + + ret = get_led(&dev, "u-boot,boot-led"); + if (ret) + return ret; + + ret = led_set_state(dev, cmd); + return ret; +} + +static int board_check_usb_power(void) +{ + struct ofnode_phandle_args adc_args; + struct udevice *adc; + struct udevice *led; + ofnode node; + unsigned int raw; + int max_uV = 0; + int ret, uV, adc_count; + u8 i, nb_blink; + + node = ofnode_path("/config"); + if (!ofnode_valid(node)) { + debug("%s: no /config node?\n", __func__); + return -ENOENT; + } + + /* + * Retrieve the ADC channels devices and get measurement + * for each of them + */ + adc_count = ofnode_count_phandle_with_args(node, "st,adc_usb_pd", + "#io-channel-cells"); + if (adc_count < 0) { + if (adc_count == -ENOENT) + return 0; + + pr_err("%s: can't find adc channel (%d)\n", __func__, + adc_count); + + return adc_count; + } + + for (i = 0; i < adc_count; i++) { + if (ofnode_parse_phandle_with_args(node, "st,adc_usb_pd", + "#io-channel-cells", 0, i, + &adc_args)) { + pr_debug("%s: can't find /config/st,adc_usb_pd\n", + __func__); + return 0; + } + + ret = uclass_get_device_by_ofnode(UCLASS_ADC, adc_args.node, + &adc); + + if (ret) { + pr_err("%s: Can't get adc device(%d)\n", __func__, + ret); + return ret; + } + + ret = adc_channel_single_shot(adc->name, adc_args.args[0], + &raw); + if (ret) { + pr_err("%s: single shot failed for %s[%d]!\n", + __func__, adc->name, adc_args.args[0]); + return ret; + } + /* Convert to uV */ + if (!adc_raw_to_uV(adc, raw, &uV)) { + if (uV > max_uV) + max_uV = uV; + pr_debug("%s: %s[%02d] = %u, %d uV\n", __func__, + adc->name, adc_args.args[0], raw, uV); + } else { + pr_err("%s: Can't get uV value for %s[%d]\n", + __func__, adc->name, adc_args.args[0]); + } + } + + /* + * If highest value is inside 1.23 Volts and 2.10 Volts, that means + * board is plugged on an USB-C 3A power supply and boot process can + * continue. + */ + if (max_uV > USB_START_LOW_THRESHOLD_UV && + max_uV < USB_START_HIGH_THRESHOLD_UV) + return 0; + + /* Display warning message and make u-boot,error-led blinking */ + pr_err("\n*******************************************\n"); + + if (max_uV < USB_WARNING_LOW_THRESHOLD_UV) { + pr_err("* WARNING 500mA power supply detected *\n"); + nb_blink = 2; + } else { + pr_err("* WARNING 1.5A power supply detected *\n"); + nb_blink = 3; + } + + pr_err("* Current too low, use a 3A power supply! *\n"); + pr_err("*******************************************\n\n"); + + ret = get_led(&led, "u-boot,error-led"); + if (ret) + return ret; + + for (i = 0; i < nb_blink * 2; i++) { + led_set_state(led, LEDST_TOGGLE); + mdelay(125); + } + led_set_state(led, LEDST_ON); + + return 0; +} + int board_usb_cleanup(int index, enum usb_init_type init) { /* Reset usbotg */ @@ -234,5 +378,13 @@ int board_init(void) if (IS_ENABLED(CONFIG_LED)) led_default_state();
+ /* for DK1/DK2 boards */ + board_check_usb_power(); + return 0; } + +void board_quiesce_devices(void) +{ + setup_led(LEDST_OFF); +}