Signed-off-by: Jon Loeliger jdl@freescale.com ---
This is all 85xx boards, not just the Freescale 85xx boards.
Tested by building all boards in ./MAKEALL 85xx.
Note that very minor liberties were taken in a few of these conversions. Specifically, I did not care much if I slightly altered the set of commands that were present under the nefarious CFG_RAMBOOT setting if it made the general case simpler and clearer.
include/configs/MPC8540ADS.h | 49 ++++++++++++--------------------- include/configs/MPC8540EVAL.h | 36 +++++++++++------------- include/configs/MPC8541CDS.h | 28 +++++++++--------- include/configs/MPC8544DS.h | 33 +++++++++++----------- include/configs/MPC8548CDS.h | 28 +++++++++--------- include/configs/MPC8555CDS.h | 28 +++++++++--------- include/configs/MPC8560ADS.h | 61 ++++++++++++++--------------------------- include/configs/MPC8568MDS.h | 29 ++++++++++--------- include/configs/PM854.h | 58 ++++++++++++++------------------------- include/configs/PM856.h | 55 +++++++++++++----------------------- include/configs/SBC8540.h | 46 +++++++++++++++--------------- include/configs/TQM85xx.h | 38 +++++++++++++------------ include/configs/sbc8560.h | 44 +++++++++++++++--------------- include/configs/stxgp3.h | 51 +++++++++++++++------------------- include/configs/stxssa.h | 46 ++++++++++++++----------------- 15 files changed, 280 insertions(+), 350 deletions(-)
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 5aeea58..bc562a3 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -407,37 +407,24 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + #if defined(CFG_RAMBOOT) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_PCI \ - | CFG_CMD_I2C) \ - & \ - ~(CFG_CMD_ENV \ - | CFG_CMD_LOADS)) - #else - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) \ - & \ - ~(CFG_CMD_ENV \ - | CFG_CMD_LOADS)) - #endif -#else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #else - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -448,7 +435,7 @@ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -469,7 +456,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -481,7 +468,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h index 418a3a3..2b0bd9b 100644 --- a/include/configs/MPC8540EVAL.h +++ b/include/configs/MPC8540EVAL.h @@ -259,26 +259,24 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) -#if defined(CONFIG_PCI) -#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING \ - | CFG_CMD_PCI | CFG_CMD_I2C ) & \ - ~(CFG_CMD_ENV | CFG_CMD_LOADS )) -#else -#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING \ - | CFG_CMD_I2C ) & \ - ~(CFG_CMD_ENV | CFG_CMD_LOADS )) -#endif -#else + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + #if defined(CONFIG_PCI) -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI \ - | CFG_CMD_PING | CFG_CMD_I2C ) -#else -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_I2C ) + #define CONFIG_CMD_PCI #endif + +#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -288,7 +286,7 @@ #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "MPC8540EVAL=> "/* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -308,7 +306,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif
@@ -320,7 +318,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index fb360d2..78e603c 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -401,19 +401,19 @@ extern unsigned long get_clock_freq(void); #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + #if defined(CONFIG_PCI) -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) -#else -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) + #define CONFIG_CMD_PCI #endif -#include <cmd_confdefs.h> +
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -423,7 +423,7 @@ extern unsigned long get_clock_freq(void); #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -443,7 +443,7 @@ extern unsigned long get_clock_freq(void); /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -455,7 +455,7 @@ extern unsigned long get_clock_freq(void); #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 4c34308..2d86d3e 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -392,21 +392,22 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + #if defined(CONFIG_PCI) -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII \ - | CFG_CMD_BEDBUG \ - | CFG_CMD_NET) -#else -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) + #define CONFIG_CMD_PCI + #define CONFIG_CMD_BEDBUG + #define CONFIG_CMD_NET #endif -#include <cmd_confdefs.h> +
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -416,7 +417,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -436,7 +437,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -448,7 +449,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 680009d..ceec7a9 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -427,19 +427,19 @@ extern unsigned long get_clock_freq(void); #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + #if defined(CONFIG_PCI) -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) -#else -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) + #define CONFIG_CMD_PCI #endif -#include <cmd_confdefs.h> +
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -449,7 +449,7 @@ extern unsigned long get_clock_freq(void); #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -469,7 +469,7 @@ extern unsigned long get_clock_freq(void); /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -481,7 +481,7 @@ extern unsigned long get_clock_freq(void); #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 4c8b4e7..6a4ebb8 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -401,19 +401,19 @@ extern unsigned long get_clock_freq(void); #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + #if defined(CONFIG_PCI) -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) -#else -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) + #define CONFIG_CMD_PCI #endif -#include <cmd_confdefs.h> +
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -423,7 +423,7 @@ extern unsigned long get_clock_freq(void); #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -443,7 +443,7 @@ extern unsigned long get_clock_freq(void); /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -455,7 +455,7 @@ extern unsigned long get_clock_freq(void); #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index 21e6637..0b4464b 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -432,46 +432,27 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif + #if defined(CFG_RAMBOOT) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_PCI \ - | CFG_CMD_I2C) \ - & \ - ~(CFG_CMD_ENV \ - | CFG_CMD_LOADS)) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) \ - & ~(CFG_CMD_ENV)) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_MII \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) \ - & ~(CFG_CMD_ENV)) - #endif -#else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_MII \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -482,7 +463,7 @@ #define CFG_LOAD_ADDR 0x1000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -503,7 +484,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -515,7 +496,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 3f65644..3aba995 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -383,19 +383,20 @@ extern unsigned long get_clock_freq(void); #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + #if defined(CONFIG_PCI) -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) -#else -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) + #define CONFIG_CMD_PCI #endif -#include <cmd_confdefs.h> +
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -405,7 +406,7 @@ extern unsigned long get_clock_freq(void); #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -425,7 +426,7 @@ extern unsigned long get_clock_freq(void); /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -437,7 +438,7 @@ extern unsigned long get_clock_freq(void); #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/PM854.h b/include/configs/PM854.h index 4fb5440..465b472 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -303,43 +303,27 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_DATE +#define CONFIG_CMD_EEPROM + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + #if defined(CFG_RAMBOOT) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_PCI \ - | CFG_CMD_I2C) \ - & \ - ~(CFG_CMD_ENV \ - | CFG_CMD_LOADS)) - #else - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) \ - & \ - ~(CFG_CMD_ENV \ - | CFG_CMD_LOADS)) - #endif -#else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_EEPROM \ - | CFG_CMD_DATE \ - | CFG_CMD_MII \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #else - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_EEPROM \ - | CFG_CMD_DATE \ - | CFG_CMD_MII \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -350,7 +334,7 @@ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -372,7 +356,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -384,7 +368,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/PM856.h b/include/configs/PM856.h index 87ab934..25c6e15 100644 --- a/include/configs/PM856.h +++ b/include/configs/PM856.h @@ -306,41 +306,26 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_DATE +#define CONFIG_CMD_EEPROM + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + #if defined(CFG_RAMBOOT) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_PCI \ - | CFG_CMD_I2C) \ - & \ - ~(CFG_CMD_ENV \ - | CFG_CMD_LOADS)) - #else - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) \ - & \ - ~(CFG_CMD_ENV \ - | CFG_CMD_LOADS)) - #endif -#else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_EEPROM \ - | CFG_CMD_DATE \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #else - #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_EEPROM \ - | CFG_CMD_DATE \ - | CFG_CMD_PING \ - | CFG_CMD_I2C) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -351,7 +336,7 @@ #define CFG_LOAD_ADDR 0x1000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -373,7 +358,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif
@@ -385,7 +370,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index f8e3397..a5397c2 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -338,28 +338,28 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV | \ - CFG_CMD_LOADS )) - #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV)) - #endif -#else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) - #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) - #endif + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif + +#if defined(CFG_RAMBOOT) + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -368,7 +368,7 @@ */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "SBC8540=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -389,7 +389,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif
@@ -401,7 +401,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index f45f3a2..3b746df 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -357,24 +357,26 @@
#define CONFIG_TIMESTAMP /* Print image info with ts */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_DATE +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_DTT +#define CONFIG_CMD_MII + #if defined(CONFIG_PCI) -# define ADD_PCI_CMD (CFG_CMD_PCI) -#else -# define ADD_PCI_CMD 0 + #define CONFIG_CMD_PCI #endif
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_DHCP | \ - CFG_CMD_NFS | \ - CFG_CMD_SNTP | \ - ADD_PCI_CMD | \ - CFG_CMD_I2C | \ - CFG_CMD_DATE | \ - CFG_CMD_EEPROM | \ - CFG_CMD_DTT | \ - CFG_CMD_MII | \ - CFG_CMD_PING ) -#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -385,7 +387,7 @@ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -406,7 +408,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ #endif
@@ -418,7 +420,7 @@ #define BOOTFLAG_COLD 0x01 /* Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index 6e4fdb2..ad610f0 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -320,28 +320,28 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif + #if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV | \ - CFG_CMD_LOADS )) - #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV)) - #endif -#else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) - #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -350,7 +350,7 @@ */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "SBC8560=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -371,7 +371,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif
@@ -383,7 +383,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index 625cf20..0a1331d 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -298,34 +298,29 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + #if defined(CFG_RAMBOOT) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV | \ - CFG_CMD_LOADS )) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \ - CFG_CMD_MII | CFG_CMD_I2C ) & \ - ~(CFG_CMD_ENV)) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV)) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \ - CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) - #endif + #define CONFIG_CMD_ELF +#endif + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI #endif -#include <cmd_confdefs.h> + +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif +
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -334,7 +329,7 @@ */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "GPPP=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -355,7 +350,7 @@ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif
@@ -367,7 +362,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 1978a32..cea5b7e 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -325,34 +325,30 @@
#define CONFIG_TIMESTAMP /* Print image info with ts */
+ +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif + #if defined(CFG_RAMBOOT) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV | \ - CFG_CMD_LOADS )) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \ - CFG_CMD_MII | CFG_CMD_I2C ) & \ - ~(CFG_CMD_ENV)) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV)) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \ - CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) - #endif + #define CONFIG_CMD_ELF #endif -#include <cmd_confdefs.h> +
#undef CONFIG_WATCHDOG /* watchdog disabled */