Add a script to generate binaries from bl31.elf, and generate u-boot.its file for FIT image including u-boot, dtb and atf binaries.
Signed-off-by: Kever Yang kever.yang@rock-chips.com ---
board/rockchip/evb_rk3328/mk_fit_atf.sh | 108 ++++++++++++++++++++++++++++++++ 1 file changed, 108 insertions(+) create mode 100755 board/rockchip/evb_rk3328/mk_fit_atf.sh
diff --git a/board/rockchip/evb_rk3328/mk_fit_atf.sh b/board/rockchip/evb_rk3328/mk_fit_atf.sh new file mode 100755 index 0000000..192c303 --- /dev/null +++ b/board/rockchip/evb_rk3328/mk_fit_atf.sh @@ -0,0 +1,108 @@ +#!/bin/sh +# +# script to generate FIT image source for rk3399 boards with +# ARM Trusted Firmware and multiple device trees (given on the command line) +# +# usage: $0 <dt_name> [<dt_name> [<dt_name] ...] + +[ -z "$BL31" ] && BL31="bl31.elf" + +if [ ! -f $BL31 ]; then + echo "WARNING: BL31 file $BL31 NOT found, resulting binary is non-functional" >&2 + BL31=/dev/null +fi + +cat << __HEADER_EOF +/dts-v1/; + +/ { + description = "Configuration to load ATF before U-Boot"; + #address-cells = <1>; + + images { + uboot@1 { + description = "U-Boot (64-bit)"; + data = /incbin/("u-boot-nodtb.bin"); + type = "standalone"; + arch = "arm64"; + compression = "none"; + load = <0x00200000>; + }; +__HEADER_EOF + +atf_cnt=1 + +for l in `readelf -l $BL31 | grep -A1 LOAD | gawk --non-decimal-data \ + '{if (NR % 2) {printf "%d:0x%x:", $2,$4} else {printf "%d\n", $1}}'` +do + offset=${l%%:*} + ll=${l#*:} + phy_offset=${ll%:*} + filesz=${ll##*:} + + #echo "$offset/$phy_offset/$filesz" + + of=bl31_${phy_offset}.bin + dd if=$BL31 of=$of bs=1 skip=$offset count=$filesz + + out_string="${out_string}:${phy_offset}" + + cat << __ATF1_EOF + atf@$atf_cnt { + description = "ARM Trusted Firmware"; + data = /incbin/("$of"); + type = "firmware"; + arch = "arm64"; + compression = "none"; + load = <$phy_offset>; +__ATF1_EOF + if [ "$atf_cnt" -eq 1 ]; then + cat << __ATF2_EOF + entry = <$phy_offset>; +__ATF2_EOF + fi + cat << __ATF3_EOF + }; +__ATF3_EOF + atf_cnt=$((atf_cnt + 1)) +done + +cnt=1 +for dtname in $* +do + cat << __FDT_IMAGE_EOF + fdt@$cnt { + description = "$(basename $dtname .dtb)"; + data = /incbin/("$dtname"); + type = "flat_dt"; + compression = "none"; + }; +__FDT_IMAGE_EOF + cnt=$((cnt+1)) +done + +cat << __CONF_HEADER_EOF + }; + configurations { + default = "config@1"; + +__CONF_HEADER_EOF + +cnt=1 +for dtname in $* +do + cat << __CONF_SECTION_EOF + config@$cnt { + description = "$(basename $dtname .dtb)"; + firmware = "uboot@1"; + loadables = "atf@1","atf@2"; + fdt = "fdt@1"; + }; +__CONF_SECTION_EOF + cnt=$((cnt+1)) +done + +cat << __ITS_EOF + }; +}; +__ITS_EOF