From: Peng Fan peng.fan@nxp.com
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already marked with u-boot,dm-spl. Move preloader_console_init after spl_early_init to make sure driver model work.
Signed-off-by: Peng Fan peng.fan@nxp.com Reviewed-by: Fabio Estevam festevam@denx.de --- board/data_modul/imx8mm_edm_sbc/spl.c | 12 ++---------- configs/imx8mm_data_modul_edm_sbc_defconfig | 1 - include/configs/imx8mm_data_modul_edm_sbc.h | 2 -- 3 files changed, 2 insertions(+), 13 deletions(-)
diff --git a/board/data_modul/imx8mm_edm_sbc/spl.c b/board/data_modul/imx8mm_edm_sbc/spl.c index 36cad14fc41..f5063eb8c19 100644 --- a/board/data_modul/imx8mm_edm_sbc/spl.c +++ b/board/data_modul/imx8mm_edm_sbc/spl.c @@ -28,14 +28,8 @@
DECLARE_GLOBAL_DATA_PTR;
-#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1) #define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
-static const iomux_v3_cfg_t uart_pads[] = { - IMX8MM_PAD_UART3_RXD_UART3_RX | MUX_PAD_CTRL(UART_PAD_CTRL), - IMX8MM_PAD_UART3_TXD_UART3_TX | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - static const iomux_v3_cfg_t wdog_pads[] = { IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL), }; @@ -47,8 +41,6 @@ static void data_modul_imx8mm_edm_sbc_early_init_f(void) imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog); - - imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads)); }
static int data_modul_imx8mm_edm_sbc_board_power_init(void) @@ -149,8 +141,6 @@ void board_init_f(ulong dummy)
data_modul_imx8mm_edm_sbc_early_init_f();
- preloader_console_init(); - /* Clear the BSS. */ memset(__bss_start, 0, __bss_end - __bss_start);
@@ -160,6 +150,8 @@ void board_init_f(ulong dummy) hang(); }
+ preloader_console_init(); + ret = uclass_get_device_by_name(UCLASS_CLK, "clock-controller@30380000", &dev); diff --git a/configs/imx8mm_data_modul_edm_sbc_defconfig b/configs/imx8mm_data_modul_edm_sbc_defconfig index afc8c43ca99..dd3c2e19e52 100644 --- a/configs/imx8mm_data_modul_edm_sbc_defconfig +++ b/configs/imx8mm_data_modul_edm_sbc_defconfig @@ -200,7 +200,6 @@ CONFIG_DM_RTC=y CONFIG_RTC_M41T62=y CONFIG_CONS_INDEX=2 CONFIG_DM_SERIAL=y -# CONFIG_SPL_DM_SERIAL is not set CONFIG_MXC_UART=y CONFIG_SPI=y CONFIG_DM_SPI=y diff --git a/include/configs/imx8mm_data_modul_edm_sbc.h b/include/configs/imx8mm_data_modul_edm_sbc.h index 33778a2365e..ff98095d27d 100644 --- a/include/configs/imx8mm_data_modul_edm_sbc.h +++ b/include/configs/imx8mm_data_modul_edm_sbc.h @@ -41,8 +41,6 @@ #define PHYS_SDRAM 0x40000000 #define PHYS_SDRAM_SIZE 0x40000000 /* Minimum 1 GiB DDR */
-#define CONFIG_MXC_UART_BASE UART3_BASE_ADDR - /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 2048 #define CONFIG_SYS_MAXARGS 64