The new configs/imx28_xea_sb_defconfig is introduced to facilitate building the single binary u-boot.sb fox XEA board.
The biggest distinction from "normal" XEA imx28_xea_sb_defconfig is support for USB mass storage devices (pen drives).
To achieve that, the CONFIG_DM_USB is enabled and supported.
Signed-off-by: Lukasz Majewski lukma@denx.de ---
configs/imx28_xea_sb_defconfig | 112 +++++++++++++++++++++++++++++++++ 1 file changed, 112 insertions(+) create mode 100644 configs/imx28_xea_sb_defconfig
diff --git a/configs/imx28_xea_sb_defconfig b/configs/imx28_xea_sb_defconfig new file mode 100644 index 00000000000..9513c5c695a --- /dev/null +++ b/configs/imx28_xea_sb_defconfig @@ -0,0 +1,112 @@ +CONFIG_ARM=y +CONFIG_SPL_SYS_THUMB_BUILD=y +CONFIG_ARCH_MX28=y +CONFIG_SYS_TEXT_BASE=0x40002000 +CONFIG_SYS_MALLOC_F_LEN=0x800 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DM_GPIO=y +CONFIG_SPL_DM_SPI=y +CONFIG_DEFAULT_DEVICE_TREE="imx28-xea" +CONFIG_SPL_TEXT_BASE=0x1000 +CONFIG_TARGET_XEA=y +CONFIG_SPL_SYS_MALLOC_F_LEN=0x1000 +CONFIG_SPL=y +CONFIG_ENV_OFFSET_REDUND=0x90000 +CONFIG_SPL_PAYLOAD="u-boot.img" +CONFIG_SYS_LOAD_ADDR=0x42000000 +CONFIG_FIT=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200n8" +CONFIG_USE_PREBOOT=y +CONFIG_PREBOOT="run prebootcmd" +CONFIG_BOARD_EARLY_INIT_F=y +# CONFIG_SPL_FRAMEWORK is not set +CONFIG_SPL_BOARD_INIT=y +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0 +CONFIG_SUPPORT_EMMC_BOOT_OVERRIDE_PART_CONFIG=y +CONFIG_SPL_DMA=y +CONFIG_SPL_DM_SPI_FLASH=y +CONFIG_SPL_OS_BOOT=y +CONFIG_HUSH_PARSER=y +CONFIG_CMD_SPL=y +CONFIG_CMD_ASKENV=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +# CONFIG_CMD_PINMUX is not set +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi3.0" +CONFIG_MTDPARTS_DEFAULT="spi3.0:64k(SPL),448k(uboot),128k(envs),384k(unused1),4096k(kernel),8192k(swupdate),-(unused2)" +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent interrupts" +CONFIG_SPL_OF_PLATDATA=y +# CONFIG_SPL_OF_PLATDATA_PARENT is not set +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_USE_ENV_SPI_BUS=y +CONFIG_ENV_SPI_BUS=3 +CONFIG_USE_ENV_SPI_CS=y +CONFIG_ENV_SPI_CS=0 +CONFIG_USE_ENV_SPI_MAX_HZ=y +CONFIG_ENV_SPI_MAX_HZ=40000000 +CONFIG_USE_ENV_SPI_MODE=y +CONFIG_ENV_SPI_MODE=0x0 +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SPL_DM=y +CONFIG_DEVRES=y +# CONFIG_SPL_BLK is not set +CONFIG_MXS_GPIO=y +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_MMC_MXS=y +CONFIG_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SF_DEFAULT_BUS=3 +CONFIG_SF_DEFAULT_MODE=0x0 +CONFIG_SF_DEFAULT_SPEED=40000000 +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_ISSI=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_ADDR_ENABLE=y +CONFIG_PHY_ADDR=1 +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_MXS=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_CONS_INDEX=0 +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_MXS_SPI=y +CONFIG_USB=y +# CONFIG_SPL_DM_USB is not set +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_FS_FAT=y +# CONFIG_SPL_OF_LIBFDT is not set