This has not been converted to Generic Board, so should be removed. (See doc/README.generic-board for details.)
Remove CONFIG_LWMON5 references. (Also, remove undefined CONFIG_WD_MAX_RATE while I am here.)
Signed-off-by: Masahiro Yamada yamada.masahiro@socionext.com Cc: Stefan Roese sr@denx.de ---
arch/powerpc/cpu/ppc4xx/Kconfig | 5 - arch/powerpc/include/asm/global_data.h | 6 - board/lwmon5/Kconfig | 9 - board/lwmon5/MAINTAINERS | 7 - board/lwmon5/Makefile | 9 - board/lwmon5/config.mk | 18 - board/lwmon5/init.S | 75 ---- board/lwmon5/kbd.c | 490 ----------------------- board/lwmon5/lwmon5.c | 558 -------------------------- board/lwmon5/sdram.c | 247 ------------ configs/lcd4_lwmon5_defconfig | 6 - configs/lwmon5_defconfig | 4 - doc/README.scrapyard | 1 + drivers/video/mb862xx.c | 3 +- include/configs/lwmon5.h | 692 --------------------------------- 15 files changed, 2 insertions(+), 2128 deletions(-) delete mode 100644 board/lwmon5/Kconfig delete mode 100644 board/lwmon5/MAINTAINERS delete mode 100644 board/lwmon5/Makefile delete mode 100644 board/lwmon5/config.mk delete mode 100644 board/lwmon5/init.S delete mode 100644 board/lwmon5/kbd.c delete mode 100644 board/lwmon5/lwmon5.c delete mode 100644 board/lwmon5/sdram.c delete mode 100644 configs/lcd4_lwmon5_defconfig delete mode 100644 configs/lwmon5_defconfig delete mode 100644 include/configs/lwmon5.h
diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig index c6bbe12..883463a 100644 --- a/arch/powerpc/cpu/ppc4xx/Kconfig +++ b/arch/powerpc/cpu/ppc4xx/Kconfig @@ -8,10 +8,6 @@ choice prompt "Target select" optional
-config TARGET_LWMON5 - bool "Support lwmon5" - select SUPPORT_SPL - config TARGET_PCS440EP bool "Support pcs440ep"
@@ -181,7 +177,6 @@ source "board/gdsys/405ex/Kconfig" source "board/gdsys/dlvision/Kconfig" source "board/gdsys/gdppc440etx/Kconfig" source "board/gdsys/intip/Kconfig" -source "board/lwmon5/Kconfig" source "board/mosaixtech/icon/Kconfig" source "board/mpl/mip405/Kconfig" source "board/mpl/pip405/Kconfig" diff --git a/arch/powerpc/include/asm/global_data.h b/arch/powerpc/include/asm/global_data.h index 4090975..2527ef8 100644 --- a/arch/powerpc/include/asm/global_data.h +++ b/arch/powerpc/include/asm/global_data.h @@ -106,12 +106,6 @@ struct arch_global_data { #ifdef CONFIG_SYS_FPGA_COUNT unsigned fpga_state[CONFIG_SYS_FPGA_COUNT]; #endif -#if defined(CONFIG_WD_MAX_RATE) - unsigned long long wdt_last; /* trace watch-dog triggering rate */ -#endif -#if defined(CONFIG_LWMON5) - unsigned long kbd_status; -#endif };
#include <asm-generic/global_data.h> diff --git a/board/lwmon5/Kconfig b/board/lwmon5/Kconfig deleted file mode 100644 index 90566d8..0000000 --- a/board/lwmon5/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_LWMON5 - -config SYS_BOARD - default "lwmon5" - -config SYS_CONFIG_NAME - default "lwmon5" - -endif diff --git a/board/lwmon5/MAINTAINERS b/board/lwmon5/MAINTAINERS deleted file mode 100644 index 7402ab6..0000000 --- a/board/lwmon5/MAINTAINERS +++ /dev/null @@ -1,7 +0,0 @@ -LWMON5 BOARD -M: Stefan Roese sr@denx.de -S: Maintained -F: board/lwmon5/ -F: include/configs/lwmon5.h -F: configs/lcd4_lwmon5_defconfig -F: configs/lwmon5_defconfig diff --git a/board/lwmon5/Makefile b/board/lwmon5/Makefile deleted file mode 100644 index 02478ca..0000000 --- a/board/lwmon5/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2002-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = lwmon5.o kbd.o sdram.o -extra-y += init.o diff --git a/board/lwmon5/config.mk b/board/lwmon5/config.mk deleted file mode 100644 index d0348e8..0000000 --- a/board/lwmon5/config.mk +++ /dev/null @@ -1,18 +0,0 @@ -# -# (C) Copyright 2002 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# lwmon5 (440EPx) -# - -PLATFORM_CPPFLAGS += -DCONFIG_440=1 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 -endif diff --git a/board/lwmon5/init.S b/board/lwmon5/init.S deleted file mode 100644 index e5207c2..0000000 --- a/board/lwmon5/init.S +++ /dev/null @@ -1,75 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * Copyright (C) 2002 Scott McNutt smcnutt@artesyncp.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <asm-offsets.h> -#include <ppc_asm.tmpl> -#include <config.h> -#include <asm/mmu.h> - -/************************************************************************** - * TLB TABLE - * - * This table is used by the cpu boot code to setup the initial tlb - * entries. Rather than make broad assumptions in the cpu source tree, - * this table lets each board set things up however they like. - * - * Pointer to the table is returned in r1 - * - *************************************************************************/ - .section .bootpg,"ax" - .globl tlbtab - -tlbtab: - tlbtab_start - - /* - * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the - * speed up boot process. It is patched after relocation to enable SA_I - */ - tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G) - - /* - * TLB entries for SDRAM are not needed on this platform. - * They are dynamically generated in the SPD DDR(2) detection - * routine. - */ - -#ifdef CONFIG_SYS_INIT_RAM_DCACHE - /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ - tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G) -#endif - - /* TLB-entry for PCI Memory */ - tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG) - tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG) - tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG) - tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG) - - /* TLB-entry for the FPGA Chip select 2 */ - tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_RWX | SA_I|SA_G) - - /* TLB-entry for the FPGA Chip select 3 */ - tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_RWX | SA_I|SA_G) - - /* TLB-entry for the LIME Controller */ - tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_RWX | SA_I|SA_G) - tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_RWX | SA_I|SA_G) - tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_RWX | SA_I|SA_G) - tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_RWX | SA_I|SA_G) - - /* TLB-entry for Internal Registers & OCM */ - tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0, AC_RWX | SA_I) - - /*TLB-entry PCI registers*/ - tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RWX | SA_IG) - - /* TLB-entry for peripherals */ - tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG) - - tlbtab_end diff --git a/board/lwmon5/kbd.c b/board/lwmon5/kbd.c deleted file mode 100644 index 97962da..0000000 --- a/board/lwmon5/kbd.c +++ /dev/null @@ -1,490 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2001, 2002 - * DENX Software Engineering - * Wolfgang Denk, wd@denx.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* define DEBUG for debugging output (obviously ;-)) */ -#if 0 -#define DEBUG -#endif - -#include <common.h> -#include <i2c.h> -#include <command.h> -#include <post.h> -#include <serial.h> -#include <malloc.h> - -#include <linux/types.h> -#include <linux/string.h> /* for strdup */ - -DECLARE_GLOBAL_DATA_PTR; - -static void kbd_init (void); -static int compare_magic (uchar *kbd_data, uchar *str); - -/*--------------------- Local macros and constants --------------------*/ -#define _NOT_USED_ 0xFFFFFFFF - -/*------------------------- dspic io expander -----------------------*/ -#define DSPIC_PON_STATUS_REG 0x80A -#define DSPIC_PON_INV_STATUS_REG 0x80C -#define DSPIC_PON_KEY_REG 0x810 -/*------------------------- Keyboard controller -----------------------*/ -/* command codes */ -#define KEYBD_CMD_READ_KEYS 0x01 -#define KEYBD_CMD_READ_VERSION 0x02 -#define KEYBD_CMD_READ_STATUS 0x03 -#define KEYBD_CMD_RESET_ERRORS 0x10 - -/* status codes */ -#define KEYBD_STATUS_MASK 0x3F -#define KEYBD_STATUS_H_RESET 0x20 -#define KEYBD_STATUS_BROWNOUT 0x10 -#define KEYBD_STATUS_WD_RESET 0x08 -#define KEYBD_STATUS_OVERLOAD 0x04 -#define KEYBD_STATUS_ILLEGAL_WR 0x02 -#define KEYBD_STATUS_ILLEGAL_RD 0x01 - -/* Number of bytes returned from Keyboard Controller */ -#define KEYBD_VERSIONLEN 2 /* version information */ - -/* - * This is different from the "old" lwmon dsPIC kbd controller - * implementation. Now the controller still answers with 9 bytes, - * but the last 3 bytes are always "0x06 0x07 0x08". So we just - * set the length to compare to 6 instead of 9. - */ -#define KEYBD_DATALEN 6 /* normal key scan data */ - -/* maximum number of "magic" key codes that can be assigned */ - -static uchar kbd_addr = CONFIG_SYS_I2C_KEYBD_ADDR; -static uchar dspic_addr = CONFIG_SYS_I2C_DSPIC_IO_ADDR; - -static uchar *key_match (uchar *); - -#define KEYBD_SET_DEBUGMODE '#' /* Magic key to enable debug output */ - -/*********************************************************************** -F* Function: int board_postclk_init (void) P*A*Z* - * -P* Parameters: none -P* -P* Returnvalue: int -P* - 0 is always returned. - * -Z* Intention: This function is the board_postclk_init() method implementation -Z* for the lwmon board. - * - ***********************************************************************/ -int board_postclk_init (void) -{ - kbd_init(); - - return (0); -} - -static void kbd_init (void) -{ - uchar kbd_data[KEYBD_DATALEN]; - uchar tmp_data[KEYBD_DATALEN]; - uchar val, errcd; - int i; - - i2c_set_bus_num(0); - - gd->arch.kbd_status = 0; - - /* Forced by PIC. Delays <= 175us loose */ - udelay(1000); - - /* Read initial keyboard error code */ - val = KEYBD_CMD_READ_STATUS; - i2c_write (kbd_addr, 0, 0, &val, 1); - i2c_read (kbd_addr, 0, 0, &errcd, 1); - /* clear unused bits */ - errcd &= KEYBD_STATUS_MASK; - /* clear "irrelevant" bits. Recommended by Martin Rajek, LWN */ - errcd &= ~(KEYBD_STATUS_H_RESET|KEYBD_STATUS_BROWNOUT); - if (errcd) { - gd->arch.kbd_status |= errcd << 8; - } - /* Reset error code and verify */ - val = KEYBD_CMD_RESET_ERRORS; - i2c_write (kbd_addr, 0, 0, &val, 1); - udelay(1000); /* delay NEEDED by keyboard PIC !!! */ - - val = KEYBD_CMD_READ_STATUS; - i2c_write (kbd_addr, 0, 0, &val, 1); - i2c_read (kbd_addr, 0, 0, &val, 1); - - val &= KEYBD_STATUS_MASK; /* clear unused bits */ - if (val) { /* permanent error, report it */ - gd->arch.kbd_status |= val; - return; - } - - /* - * Read current keyboard state. - * - * After the error reset it may take some time before the - * keyboard PIC picks up a valid keyboard scan - the total - * scan time is approx. 1.6 ms (information by Martin Rajek, - * 28 Sep 2002). We read a couple of times for the keyboard - * to stabilize, using a big enough delay. - * 10 times should be enough. If the data is still changing, - * we use what we get :-( - */ - - memset (tmp_data, 0xFF, KEYBD_DATALEN); /* impossible value */ - for (i=0; i<10; ++i) { - val = KEYBD_CMD_READ_KEYS; - i2c_write (kbd_addr, 0, 0, &val, 1); - i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN); - - if (memcmp(kbd_data, tmp_data, KEYBD_DATALEN) == 0) { - /* consistent state, done */ - break; - } - /* remeber last state, delay, and retry */ - memcpy (tmp_data, kbd_data, KEYBD_DATALEN); - udelay (5000); - } -} - - -/* Read a register from the dsPIC. */ -int _dspic_read(ushort reg, ushort *data) -{ - uchar buf[sizeof(*data)]; - int rval; - - if (i2c_read(dspic_addr, reg, 2, buf, 2)) - return -1; - - rval = i2c_read(dspic_addr, reg, sizeof(reg), buf, sizeof(*data)); - *data = (buf[0] << 8) | buf[1]; - - return rval; -} - - -/*********************************************************************** -F* Function: int misc_init_r (void) P*A*Z* - * -P* Parameters: none -P* -P* Returnvalue: int -P* - 0 is always returned, even in the case of a keyboard -P* error. - * -Z* Intention: This function is the misc_init_r() method implementation -Z* for the lwmon board. -Z* The keyboard controller is initialized and the result -Z* of a read copied to the environment variable "keybd". -Z* If KEYBD_SET_DEBUGMODE is defined, a check is made for -Z* this key, and if found display to the LCD will be enabled. -Z* The keys in "keybd" are checked against the magic -Z* keycommands defined in the environment. -Z* See also key_match(). - * -D* Design: wd@denx.de -C* Coding: wd@denx.de -V* Verification: dzu@denx.de - ***********************************************************************/ -int misc_init_r_kbd (void) -{ - uchar kbd_data[KEYBD_DATALEN]; - char keybd_env[2 * KEYBD_DATALEN + 1]; - uchar kbd_init_status = gd->arch.kbd_status >> 8; - uchar kbd_status = gd->arch.kbd_status; - uchar val; - ushort data, inv_data; - char *str; - int i; - - if (kbd_init_status) { - printf ("KEYBD: Error %02X\n", kbd_init_status); - } - if (kbd_status) { /* permanent error, report it */ - printf ("*** Keyboard error code %02X ***\n", kbd_status); - sprintf (keybd_env, "%02X", kbd_status); - setenv ("keybd", keybd_env); - return 0; - } - - /* - * Now we know that we have a working keyboard, so disable - * all output to the LCD except when a key press is detected. - */ - - if ((console_assign (stdout, "serial") < 0) || - (console_assign (stderr, "serial") < 0)) { - printf ("Can't assign serial port as output device\n"); - } - - /* Read Version */ - val = KEYBD_CMD_READ_VERSION; - i2c_write (kbd_addr, 0, 0, &val, 1); - i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_VERSIONLEN); - printf ("KEYBD: Version %d.%d\n", kbd_data[0], kbd_data[1]); - - /* Read current keyboard state */ - val = KEYBD_CMD_READ_KEYS; - i2c_write (kbd_addr, 0, 0, &val, 1); - i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN); - - /* read out start key from bse01 received via can */ - _dspic_read(DSPIC_PON_STATUS_REG, &data); - /* check highbyte from status register */ - if (data > 0xFF) { - _dspic_read(DSPIC_PON_INV_STATUS_REG, &inv_data); - - /* check inverse data */ - if ((data+inv_data) == 0xFFFF) { - /* don't overwrite local key */ - if (kbd_data[1] == 0) { - /* read key value */ - _dspic_read(DSPIC_PON_KEY_REG, &data); - str = (char *)&data; - /* swap bytes */ - kbd_data[1] = str[1]; - kbd_data[2] = str[0]; - printf("CAN received startkey: 0x%X\n", data); - } - } - } - - for (i = 0; i < KEYBD_DATALEN; ++i) { - sprintf (keybd_env + i + i, "%02X", kbd_data[i]); - } - - setenv ("keybd", keybd_env); - - str = strdup ((char *)key_match (kbd_data)); /* decode keys */ -#ifdef KEYBD_SET_DEBUGMODE - if (kbd_data[0] == KEYBD_SET_DEBUGMODE) { /* set debug mode */ - if ((console_assign (stdout, "lcd") < 0) || - (console_assign (stderr, "lcd") < 0)) { - printf ("Can't assign LCD display as output device\n"); - } - } -#endif /* KEYBD_SET_DEBUGMODE */ -#ifdef CONFIG_PREBOOT /* automatically configure "preboot" command on key match */ - setenv ("preboot", str); /* set or delete definition */ -#endif /* CONFIG_PREBOOT */ - if (str != NULL) { - free (str); - } - return (0); -} - -#ifdef CONFIG_PREBOOT - -static uchar kbd_magic_prefix[] = "key_magic"; -static uchar kbd_command_prefix[] = "key_cmd"; - -static int compare_magic (uchar *kbd_data, uchar *str) -{ - uchar compare[KEYBD_DATALEN-1]; - char *nxt; - int i; - - /* Don't include modifier byte */ - memcpy (compare, kbd_data+1, KEYBD_DATALEN-1); - - for (; str != NULL; str = (*nxt) ? (uchar *)(nxt+1) : (uchar *)nxt) { - uchar c; - int k; - - c = (uchar) simple_strtoul ((char *)str, (char **) (&nxt), 16); - - if (str == (uchar *)nxt) { /* invalid character */ - break; - } - - /* - * Check if this key matches the input. - * Set matches to zero, so they match only once - * and we can find duplicates or extra keys - */ - for (k = 0; k < sizeof(compare); ++k) { - if (compare[k] == '\0') /* only non-zero entries */ - continue; - if (c == compare[k]) { /* found matching key */ - compare[k] = '\0'; - break; - } - } - if (k == sizeof(compare)) { - return -1; /* unmatched key */ - } - } - - /* - * A full match leaves no keys in the `compare' array, - */ - for (i = 0; i < sizeof(compare); ++i) { - if (compare[i]) - { - return -1; - } - } - - return 0; -} - -/*********************************************************************** -F* Function: static uchar *key_match (uchar *kbd_data) P*A*Z* - * -P* Parameters: uchar *kbd_data -P* - The keys to match against our magic definitions -P* -P* Returnvalue: uchar * -P* - != NULL: Pointer to the corresponding command(s) -P* NULL: No magic is about to happen - * -Z* Intention: Check if pressed key(s) match magic sequence, -Z* and return the command string associated with that key(s). -Z* -Z* If no key press was decoded, NULL is returned. -Z* -Z* Note: the first character of the argument will be -Z* overwritten with the "magic charcter code" of the -Z* decoded key(s), or '\0'. -Z* -Z* Note: the string points to static environment data -Z* and must be saved before you call any function that -Z* modifies the environment. - * -D* Design: wd@denx.de -C* Coding: wd@denx.de -V* Verification: dzu@denx.de - ***********************************************************************/ -static uchar *key_match (uchar *kbd_data) -{ - char magic[sizeof (kbd_magic_prefix) + 1]; - uchar *suffix; - char *kbd_magic_keys; - - /* - * The following string defines the characters that can pe appended - * to "key_magic" to form the names of environment variables that - * hold "magic" key codes, i. e. such key codes that can cause - * pre-boot actions. If the string is empty (""), then only - * "key_magic" is checked (old behaviour); the string "125" causes - * checks for "key_magic1", "key_magic2" and "key_magic5", etc. - */ - if ((kbd_magic_keys = getenv ("magic_keys")) == NULL) - kbd_magic_keys = ""; - - /* loop over all magic keys; - * use '\0' suffix in case of empty string - */ - for (suffix=(uchar *)kbd_magic_keys; *suffix || suffix==(uchar *)kbd_magic_keys; ++suffix) { - sprintf (magic, "%s%c", kbd_magic_prefix, *suffix); - debug ("### Check magic "%s"\n", magic); - if (compare_magic(kbd_data, (uchar *)getenv(magic)) == 0) { - char cmd_name[sizeof (kbd_command_prefix) + 1]; - char *cmd; - - sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix); - - cmd = getenv (cmd_name); - debug ("### Set PREBOOT to $(%s): "%s"\n", - cmd_name, cmd ? cmd : "<<NULL>>"); - *kbd_data = *suffix; - return ((uchar *)cmd); - } - } - debug ("### Delete PREBOOT\n"); - *kbd_data = '\0'; - return (NULL); -} -#endif /* CONFIG_PREBOOT */ - -/*********************************************************************** -F* Function: int do_kbd (cmd_tbl_t *cmdtp, int flag, -F* int argc, char * const argv[]) P*A*Z* - * -P* Parameters: cmd_tbl_t *cmdtp -P* - Pointer to our command table entry -P* int flag -P* - If the CMD_FLAG_REPEAT bit is set, then this call is -P* a repetition -P* int argc -P* - Argument count -P* char * const argv[] -P* - Array of the actual arguments -P* -P* Returnvalue: int -P* - 0 is always returned. - * -Z* Intention: Implement the "kbd" command. -Z* The keyboard status is read. The result is printed on -Z* the console and written into the "keybd" environment -Z* variable. - * -D* Design: wd@denx.de -C* Coding: wd@denx.de -V* Verification: dzu@denx.de - ***********************************************************************/ -int do_kbd (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - uchar kbd_data[KEYBD_DATALEN]; - char keybd_env[2 * KEYBD_DATALEN + 1]; - uchar val; - int i; - -#if 0 /* Done in kbd_init */ - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); -#endif - - /* Read keys */ - val = KEYBD_CMD_READ_KEYS; - i2c_write (kbd_addr, 0, 0, &val, 1); - i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN); - - puts ("Keys:"); - for (i = 0; i < KEYBD_DATALEN; ++i) { - sprintf (keybd_env + i + i, "%02X", kbd_data[i]); - printf (" %02x", kbd_data[i]); - } - putc ('\n'); - setenv ("keybd", keybd_env); - return 0; -} - -U_BOOT_CMD( - kbd, 1, 1, do_kbd, - "read keyboard status", - "" -); - -/*----------------------------- Utilities -----------------------------*/ - -#ifdef CONFIG_POST -/* - * Returns 1 if keys pressed to start the power-on long-running tests - * Called from board_init_f(). - */ -int post_hotkeys_pressed(void) -{ - uchar kbd_data[KEYBD_DATALEN]; - uchar val; - - /* Read keys */ - val = KEYBD_CMD_READ_KEYS; - i2c_write (kbd_addr, 0, 0, &val, 1); - i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN); - - return (compare_magic(kbd_data, (uchar *)CONFIG_POST_KEY_MAGIC) == 0); -} -#endif diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c deleted file mode 100644 index e9aa0b7..0000000 --- a/board/lwmon5/lwmon5.c +++ /dev/null @@ -1,558 +0,0 @@ -/* - * (C) Copyright 2007-2013 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <asm/ppc440.h> -#include <asm/processor.h> -#include <asm/ppc4xx-gpio.h> -#include <asm/io.h> -#include <post.h> -#include <flash.h> -#include <mtd/cfi_flash.h> - -DECLARE_GLOBAL_DATA_PTR; - -static phys_addr_t lwmon5_cfi_flash_bank_addr[2] = CONFIG_SYS_FLASH_BANKS_LIST; - -ulong flash_get_size(ulong base, int banknum); -int misc_init_r_kbd(void); - -int board_early_init_f(void) -{ - u32 sdr0_pfc1, sdr0_pfc2; - u32 reg; - - /* PLB Write pipelining disabled. Denali Core workaround */ - mtdcr(PLB4A0_ACR, 0xDE000000); - mtdcr(PLB4A1_ACR, 0xDE000000); - - /*-------------------------------------------------------------------- - * Setup the interrupt controller polarities, triggers, etc. - *-------------------------------------------------------------------*/ - mtdcr(UIC0SR, 0xffffffff); /* clear all. if write with 1 then the status is cleared */ - mtdcr(UIC0ER, 0x00000000); /* disable all */ - mtdcr(UIC0CR, 0x00000000); /* we have not critical interrupts at the moment */ - mtdcr(UIC0PR, 0xFFBFF1EF); /* Adjustment of the polarity */ - mtdcr(UIC0TR, 0x00000900); /* per ref-board manual */ - mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 is within DDRAM */ - mtdcr(UIC0SR, 0xffffffff); /* clear all */ - - mtdcr(UIC1SR, 0xffffffff); /* clear all */ - mtdcr(UIC1ER, 0x00000000); /* disable all */ - mtdcr(UIC1CR, 0x00000000); /* all non-critical */ - mtdcr(UIC1PR, 0xFFFFC6A5); /* Adjustment of the polarity */ - mtdcr(UIC1TR, 0x60000040); /* per ref-board manual */ - mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 is within DDRAM */ - mtdcr(UIC1SR, 0xffffffff); /* clear all */ - - mtdcr(UIC2SR, 0xffffffff); /* clear all */ - mtdcr(UIC2ER, 0x00000000); /* disable all */ - mtdcr(UIC2CR, 0x00000000); /* all non-critical */ - mtdcr(UIC2PR, 0x27C00000); /* Adjustment of the polarity */ - mtdcr(UIC2TR, 0x3C000000); /* per ref-board manual */ - mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 is within DDRAM */ - mtdcr(UIC2SR, 0xffffffff); /* clear all */ - - /* Trace Pins are disabled. SDR0_PFC0 Register */ - mtsdr(SDR0_PFC0, 0x0); - - /* select Ethernet pins */ - mfsdr(SDR0_PFC1, sdr0_pfc1); - /* SMII via ZMII */ - sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) | - SDR0_PFC1_SELECT_CONFIG_6; - mfsdr(SDR0_PFC2, sdr0_pfc2); - sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) | - SDR0_PFC2_SELECT_CONFIG_6; - - /* enable SPI (SCP) */ - sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_SCP_SEL; - - mtsdr(SDR0_PFC2, sdr0_pfc2); - mtsdr(SDR0_PFC1, sdr0_pfc1); - - mtsdr(SDR0_PFC4, 0x80000000); - - /* PCI arbiter disabled */ - /* PCI Host Configuration disbaled */ - mfsdr(SDR0_PCI0, reg); - reg = 0; - mtsdr(SDR0_PCI0, 0x00000000 | reg); - - gpio_write_bit(CONFIG_SYS_GPIO_FLASH_WP, 1); - -#if CONFIG_POST & CONFIG_SYS_POST_BSPEC1 - /* enable the LSB transmitter */ - gpio_write_bit(CONFIG_SYS_GPIO_LSB_ENABLE, 1); - /* enable the CAN transmitter */ - gpio_write_bit(CONFIG_SYS_GPIO_CAN_ENABLE, 1); - - reg = 0; /* reuse as counter */ - out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR, - in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) - & ~CONFIG_SYS_DSPIC_TEST_MASK); - while (gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY) && reg++ < 1000) { - udelay(1000); - } - if (gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY)) { - /* set "boot error" flag */ - out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR, - in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) | - CONFIG_SYS_DSPIC_TEST_MASK); - } -#endif - - /* - * Reset PHY's: - * The PHY's need a 2nd reset pulse, since the MDIO address is latched - * upon reset, and with the first reset upon powerup, the addresses are - * not latched reliable, since the IRQ line is multiplexed with an - * MDIO address. A 2nd reset at this time will make sure, that the - * correct address is latched. - */ - gpio_write_bit(CONFIG_SYS_GPIO_PHY0_RST, 1); - gpio_write_bit(CONFIG_SYS_GPIO_PHY1_RST, 1); - udelay(1000); - gpio_write_bit(CONFIG_SYS_GPIO_PHY0_RST, 0); - gpio_write_bit(CONFIG_SYS_GPIO_PHY1_RST, 0); - udelay(1000); - gpio_write_bit(CONFIG_SYS_GPIO_PHY0_RST, 1); - gpio_write_bit(CONFIG_SYS_GPIO_PHY1_RST, 1); - - return 0; -} - -/* - * Override weak default with board specific version - */ -phys_addr_t cfi_flash_bank_addr(int bank) -{ - return lwmon5_cfi_flash_bank_addr[bank]; -} - -/* - * Override the weak default mapping function with a board specific one - */ -u32 flash_get_bank_size(int cs, int idx) -{ - return flash_info[idx].size; -} - -int board_early_init_r(void) -{ - u32 val0, val1; - - /* - * lwmon5 is manufactured in 2 different board versions: - * The lwmon5a board has 64MiB NOR flash instead of the - * 128MiB of the original lwmon5. Unfortunately the CFI driver - * will report 2 banks of 64MiB even for the smaller flash - * chip, since the bank is mirrored. To fix this, we bring - * one bank into CFI query mode and read its response. This - * enables us to detect the real number of flash devices/ - * banks which will be used later on by the common CFI driver. - */ - - /* Put bank 0 into CFI command mode and read */ - out_be32((void *)CONFIG_SYS_FLASH0, 0x00980098); - val0 = in_be32((void *)CONFIG_SYS_FLASH0 + FLASH_OFFSET_CFI_RESP); - val1 = in_be32((void *)CONFIG_SYS_FLASH1 + FLASH_OFFSET_CFI_RESP); - - /* Reset flash again out of query mode */ - out_be32((void *)CONFIG_SYS_FLASH0, 0x00f000f0); - - /* When not identical, we have 2 different flash devices/banks */ - if (val0 != val1) - return 0; - - /* - * Now we're sure that we're running on a LWMON5a board with - * only 64MiB NOR flash in one bank: - * - * Set flash base address and bank count for CFI driver probing. - */ - cfi_flash_num_flash_banks = 1; - lwmon5_cfi_flash_bank_addr[0] = CONFIG_SYS_FLASH0; - - return 0; -} - -int misc_init_r(void) -{ - u32 pbcr; - int size_val = 0; - u32 reg; -#ifndef CONFIG_LCD4_LWMON5 - unsigned long usb2d0cr = 0; - unsigned long usb2phy0cr, usb2h0cr = 0; - unsigned long sdr0_pfc1, sdr0_srst; -#endif - - /* - * FLASH stuff... - */ - - /* Re-do sizing to get full correct info */ - - /* adjust flash start and offset */ - gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; - gd->bd->bi_flashoffset = 0; - - mfebc(PB0CR, pbcr); - size_val = ffs(gd->bd->bi_flashsize) - 21; - pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); - mtebc(PB0CR, pbcr); - - /* - * Re-check to get correct base address - */ - flash_get_size(gd->bd->bi_flashstart, 0); - - /* Monitor protection ON by default */ - flash_protect(FLAG_PROTECT_SET, -CONFIG_SYS_MONITOR_LEN, 0xffffffff, - &flash_info[cfi_flash_num_flash_banks - 1]); - - /* Env protection ON by default */ - flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND, - CONFIG_ENV_ADDR_REDUND + 2 * CONFIG_ENV_SECT_SIZE - 1, - &flash_info[cfi_flash_num_flash_banks - 1]); - -#ifndef CONFIG_LCD4_LWMON5 - /* - * USB suff... - */ - - /* Reset USB */ - /* Reset of USB2PHY0 must be active at least 10 us */ - mtsdr(SDR0_SRST0, SDR0_SRST0_USB2H | SDR0_SRST0_USB2D); - udelay(2000); - - mtsdr(SDR0_SRST1, SDR0_SRST1_USB20PHY | SDR0_SRST1_USB2HUTMI | - SDR0_SRST1_USB2HPHY | SDR0_SRST1_OPBA2 | - SDR0_SRST1_PLB42OPB1 | SDR0_SRST1_OPB2PLB40); - udelay(2000); - - /* Errata CHIP_6 */ - - /* 1. Set internal PHY configuration */ - /* SDR Setting */ - mfsdr(SDR0_PFC1, sdr0_pfc1); - mfsdr(SDR0_USB0, usb2d0cr); - mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); - mfsdr(SDR0_USB2H0CR, usb2h0cr); - - usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/ - usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_WDINT_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/ - usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN; /*1*/ - usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/ - usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/ - - /* - * An 8-bit/60MHz interface is the only possible alternative - * when connecting the Device to the PHY - */ - usb2h0cr = usb2h0cr & ~SDR0_USB2H0CR_WDINT_MASK; - usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/ - - mtsdr(SDR0_PFC1, sdr0_pfc1); - mtsdr(SDR0_USB0, usb2d0cr); - mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); - mtsdr(SDR0_USB2H0CR, usb2h0cr); - - /* 2. De-assert internal PHY reset */ - mfsdr(SDR0_SRST1, sdr0_srst); - sdr0_srst = sdr0_srst & ~SDR0_SRST1_USB20PHY; - mtsdr(SDR0_SRST1, sdr0_srst); - - /* 3. Wait for more than 1 ms */ - udelay(2000); - - /* 4. De-assert USB 2.0 Host main reset */ - mfsdr(SDR0_SRST0, sdr0_srst); - sdr0_srst = sdr0_srst &~ SDR0_SRST0_USB2H; - mtsdr(SDR0_SRST0, sdr0_srst); - udelay(1000); - - /* 5. De-assert reset of OPB2 cores */ - mfsdr(SDR0_SRST1, sdr0_srst); - sdr0_srst = sdr0_srst &~ SDR0_SRST1_PLB42OPB1; - sdr0_srst = sdr0_srst &~ SDR0_SRST1_OPB2PLB40; - sdr0_srst = sdr0_srst &~ SDR0_SRST1_OPBA2; - mtsdr(SDR0_SRST1, sdr0_srst); - udelay(1000); - - /* 6. Set EHCI Configure FLAG */ - - /* 7. Reassert internal PHY reset: */ - mtsdr(SDR0_SRST1, SDR0_SRST1_USB20PHY); - udelay(1000); -#endif - - /* - * Clear resets - */ - mtsdr(SDR0_SRST1, 0x00000000); - mtsdr(SDR0_SRST0, 0x00000000); - -#ifndef CONFIG_LCD4_LWMON5 - printf("USB: Host(int phy) Device(ext phy)\n"); -#endif - - /* - * Clear PLB4A0_ACR[WRP] - * This fix will make the MAL burst disabling patch for the Linux - * EMAC driver obsolete. - */ - reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK; - mtdcr(PLB4A0_ACR, reg); - -#ifndef CONFIG_LCD4_LWMON5 - /* - * Init matrix keyboard - */ - misc_init_r_kbd(); -#endif - - return 0; -} - -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - printf("Board: %s", __stringify(CONFIG_HOSTNAME)); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return (0); -} - -void hw_watchdog_reset(void) -{ - int val; -#if defined(CONFIG_WD_MAX_RATE) - unsigned long long ct = get_ticks(); - - /* - * Don't allow watch-dog triggering more frequently than - * the predefined value CONFIG_WD_MAX_RATE [ticks]. - */ - if (ct >= gd->arch.wdt_last) { - if ((ct - gd->arch.wdt_last) < CONFIG_WD_MAX_RATE) - return; - } else { - /* Time base counter had been reset */ - if (((unsigned long long)(-1) - gd->arch.wdt_last + ct) < - CONFIG_WD_MAX_RATE) - return; - } - gd->arch.wdt_last = get_ticks(); -#endif - - /* - * Toggle watchdog output - */ - val = gpio_read_out_bit(CONFIG_SYS_GPIO_WATCHDOG) == 0 ? 1 : 0; - gpio_write_bit(CONFIG_SYS_GPIO_WATCHDOG, val); -} - -int do_eeprom_wp(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - if (argc < 2) - return cmd_usage(cmdtp); - - if ((strcmp(argv[1], "on") == 0)) - gpio_write_bit(CONFIG_SYS_GPIO_EEPROM_EXT_WP, 1); - else if ((strcmp(argv[1], "off") == 0)) - gpio_write_bit(CONFIG_SYS_GPIO_EEPROM_EXT_WP, 0); - else - return cmd_usage(cmdtp); - - return 0; -} - -U_BOOT_CMD( - eepromwp, 2, 0, do_eeprom_wp, - "eeprom write protect off/on", - "<on|off> - enable (on) or disable (off) I2C EEPROM write protect" -); - -#if defined(CONFIG_VIDEO) -#include <video_fb.h> -#include <mb862xx.h> - -extern GraphicDevice mb862xx; - -static const gdc_regs init_regs [] = { - { 0x0100, 0x00000f00 }, - { 0x0020, 0x801401df }, - { 0x0024, 0x00000000 }, - { 0x0028, 0x00000000 }, - { 0x002c, 0x00000000 }, - { 0x0110, 0x00000000 }, - { 0x0114, 0x00000000 }, - { 0x0118, 0x01df0280 }, - { 0x0004, 0x031f0000 }, - { 0x0008, 0x027f027f }, - { 0x000c, 0x015f028f }, - { 0x0010, 0x020c0000 }, - { 0x0014, 0x01df01ea }, - { 0x0018, 0x00000000 }, - { 0x001c, 0x01e00280 }, - { 0x0100, 0x80010f00 }, - { 0x0, 0x0 } -}; - -const gdc_regs *board_get_regs(void) -{ - return init_regs; -} - -/* Returns Lime base address */ -unsigned int board_video_init(void) -{ - /* - * Reset Lime controller - */ - gpio_write_bit(CONFIG_SYS_GPIO_LIME_S, 1); - udelay(500); - gpio_write_bit(CONFIG_SYS_GPIO_LIME_RST, 1); - - mb862xx.winSizeX = 640; - mb862xx.winSizeY = 480; - mb862xx.gdfBytesPP = 2; - mb862xx.gdfIndex = GDF_15BIT_555RGB; - - return CONFIG_SYS_LIME_BASE_0; -} - -#define DEFAULT_BRIGHTNESS 0x64 - -static void board_backlight_brightness(int brightness) -{ - if (brightness > 0) { - /* pwm duty, lamp on */ - out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000024), brightness); - out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000020), 0x701); - } else { - /* lamp off */ - out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000024), 0x00); - out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000020), 0x00); - } -} - -void board_backlight_switch(int flag) -{ - char * param; - int rc; - - if (flag) { - param = getenv("brightness"); - rc = param ? simple_strtol(param, NULL, 10) : -1; - if (rc < 0) - rc = DEFAULT_BRIGHTNESS; - } else { - rc = 0; - } - board_backlight_brightness(rc); -} - -#if defined(CONFIG_CONSOLE_EXTRA_INFO) -/* - * Return text to be printed besides the logo. - */ -void video_get_info_str(int line_number, char *info) -{ - if (line_number == 1) - strcpy(info, " Board: Lwmon5 (Liebherr Elektronik GmbH)"); - else - info [0] = '\0'; -} -#endif /* CONFIG_CONSOLE_EXTRA_INFO */ -#endif /* CONFIG_VIDEO */ - -void board_reset(void) -{ - gpio_write_bit(CONFIG_SYS_GPIO_BOARD_RESET, 1); -} - -#ifdef CONFIG_SPL_OS_BOOT -/* - * lwmon5 specific implementation of spl_start_uboot() - * - * RETURN - * 0 if booting into OS is selected (default) - * 1 if booting into U-Boot is selected - */ -int spl_start_uboot(void) -{ - char s[8]; - - env_init(); - getenv_f("boot_os", s, sizeof(s)); - if ((s != NULL) && (strcmp(s, "yes") == 0)) - return 0; - - return 1; -} - -/* - * This function is called from the SPL U-Boot version for - * early init stuff, that needs to be done for OS (e.g. Linux) - * booting. Doing it later in the real U-Boot would not work - * in case that the SPL U-Boot boots Linux directly. - */ -void spl_board_init(void) -{ - const gdc_regs *regs = board_get_regs(); - - /* - * Setup PFC registers, mainly for ethernet support - * later on in Linux - */ - board_early_init_f(); - - /* enable the LSB transmitter */ - gpio_write_bit(CONFIG_SYS_GPIO_LSB_ENABLE, 1); - - /* - * Clear resets - */ - mtsdr(SDR0_SRST1, 0x00000000); - mtsdr(SDR0_SRST0, 0x00000000); - - /* - * Reset Lime controller - */ - gpio_write_bit(CONFIG_SYS_GPIO_LIME_S, 1); - udelay(500); - gpio_write_bit(CONFIG_SYS_GPIO_LIME_RST, 1); - - out_be32((void *)CONFIG_SYS_LIME_SDRAM_CLOCK, CONFIG_SYS_MB862xx_CCF); - udelay(300); - out_be32((void *)CONFIG_SYS_LIME_MMR, CONFIG_SYS_MB862xx_MMR); - - while (regs->index) { - out_be32((void *)(CONFIG_SYS_LIME_BASE_0 + GC_DISP_BASE) + - regs->index, regs->value); - regs++; - } - - board_backlight_brightness(DEFAULT_BRIGHTNESS); -} -#endif diff --git a/board/lwmon5/sdram.c b/board/lwmon5/sdram.c deleted file mode 100644 index 5dfbb0b..0000000 --- a/board/lwmon5/sdram.c +++ /dev/null @@ -1,247 +0,0 @@ -/* - * (C) Copyright 2006 - * Sylvie Gohl, AMCC/IBM, gohl.sylvie@fr.ibm.com - * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com - * Thierry Roman, AMCC/IBM, thierry_roman@fr.ibm.com - * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com - * Robert Snyder, AMCC/IBM, rob.snyder@fr.ibm.com - * - * (C) Copyright 2007-2013 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* define DEBUG for debugging output (obviously ;-)) */ -#if 0 -#define DEBUG -#endif - -#include <common.h> -#include <asm/processor.h> -#include <asm/mmu.h> -#include <asm/io.h> -#include <asm/cache.h> -#include <asm/ppc440.h> -#include <watchdog.h> - -/* - * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory - * region. Right now the cache should still be disabled in U-Boot because of the - * EMAC driver, that need it's buffer descriptor to be located in non cached - * memory. - * - * If at some time this restriction doesn't apply anymore, just define - * CONFIG_4xx_DCACHE in the board config file and this code should setup - * everything correctly. - */ -#ifdef CONFIG_4xx_DCACHE -#define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on SDRAM */ -#else -#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */ -#endif - -/*-----------------------------------------------------------------------------+ - * Prototypes - *-----------------------------------------------------------------------------*/ -extern int denali_wait_for_dlllock(void); -extern void denali_core_search_data_eye(void); -extern void dcbz_area(u32 start_address, u32 num_bytes); - -static u32 is_ecc_enabled(void) -{ - u32 val; - - mfsdram(DDR0_22, val); - val &= DDR0_22_CTRL_RAW_MASK; - if (val) - return 1; - else - return 0; -} - -void board_add_ram_info(int use_default) -{ - PPC4xx_SYS_INFO board_cfg; - u32 val; - - if (is_ecc_enabled()) - puts(" (ECC"); - else - puts(" (ECC not"); - - get_sys_info(&board_cfg); - printf(" enabled, %ld MHz", (board_cfg.freqPLB * 2) / 1000000); - - mfsdram(DDR0_03, val); - val = DDR0_03_CASLAT_DECODE(val); - printf(", CL%d)", val); -} - -#ifdef CONFIG_DDR_ECC -static void wait_ddr_idle(void) -{ - /* - * Controller idle status cannot be determined for Denali - * DDR2 code. Just return here. - */ -} - -static void program_ecc(u32 start_address, - u32 num_bytes, - u32 tlb_word2_i_value) -{ - u32 val; - u32 current_addr = start_address; - u32 size; - int bytes_remaining; - - sync(); - wait_ddr_idle(); - - /* - * Because of 440EPx errata CHIP 11, we don't touch the last 256 - * bytes of SDRAM. - */ - bytes_remaining = num_bytes - CONFIG_SYS_MEM_TOP_HIDE; - - /* - * We have to write the ECC bytes by zeroing and flushing in smaller - * steps, since the whole 256MByte takes too long for the external - * watchdog. - */ - while (bytes_remaining > 0) { - size = min((64 << 20), bytes_remaining); - - /* Write zero's to SDRAM */ - dcbz_area(current_addr, size); - - /* Write modified dcache lines back to memory */ - clean_dcache_range(current_addr, current_addr + size); - - current_addr += 64 << 20; - bytes_remaining -= 64 << 20; - WATCHDOG_RESET(); - } - - sync(); - wait_ddr_idle(); - - /* Clear error status */ - mfsdram(DDR0_00, val); - mtsdram(DDR0_00, val | DDR0_00_INT_ACK_ALL); - - /* Set 'int_mask' parameter to functionnal value */ - mfsdram(DDR0_01, val); - mtsdram(DDR0_01, ((val &~ DDR0_01_INT_MASK_MASK) | DDR0_01_INT_MASK_ALL_OFF)); - - sync(); - wait_ddr_idle(); -} -#endif - -/************************************************************************* - * - * initdram -- 440EPx's DDR controller is a DENALI Core - * - ************************************************************************/ -phys_size_t initdram (int board_type) -{ -#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_LCD4_LWMON5) - /* CL=4 */ - mtsdram(DDR0_02, 0x00000000); - - mtsdram(DDR0_00, 0x0000190A); - mtsdram(DDR0_01, 0x01000000); - mtsdram(DDR0_03, 0x02040803); /* A suitable burst length was taken. CAS is right for our board */ - - mtsdram(DDR0_04, 0x0B030300); - mtsdram(DDR0_05, 0x02020308); - mtsdram(DDR0_06, 0x0003C812); - mtsdram(DDR0_07, 0x00090100); - mtsdram(DDR0_08, 0x03c80001); - mtsdram(DDR0_09, 0x00011D5F); - mtsdram(DDR0_10, 0x00000100); - mtsdram(DDR0_11, 0x000CC800); - mtsdram(DDR0_12, 0x00000003); - mtsdram(DDR0_14, 0x00000000); - mtsdram(DDR0_17, 0x1e000000); - mtsdram(DDR0_18, 0x1e1e1e1e); - mtsdram(DDR0_19, 0x1e1e1e1e); - mtsdram(DDR0_20, 0x0B0B0B0B); - mtsdram(DDR0_21, 0x0B0B0B0B); -#ifdef CONFIG_DDR_ECC - mtsdram(DDR0_22, 0x00267F0B | DDR0_22_CTRL_RAW_ECC_ENABLE); /* enable ECC */ -#else - mtsdram(DDR0_22, 0x00267F0B); -#endif - - mtsdram(DDR0_23, 0x01000000); - mtsdram(DDR0_24, 0x01010001); - - mtsdram(DDR0_26, 0x2D93028A); - mtsdram(DDR0_27, 0x0784682B); - - mtsdram(DDR0_28, 0x00000080); - mtsdram(DDR0_31, 0x00000000); - mtsdram(DDR0_42, 0x01000008); - - mtsdram(DDR0_43, 0x050A0200); - mtsdram(DDR0_44, 0x00000005); - mtsdram(DDR0_02, 0x00000001); /* Activate the denali core */ - - denali_wait_for_dlllock(); - -#if defined(CONFIG_DDR_DATA_EYE) - /* -----------------------------------------------------------+ - * Perform data eye search if requested. - * ----------------------------------------------------------*/ - program_tlb(0, CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20, - TLB_WORD2_I_ENABLE); - denali_core_search_data_eye(); - remove_tlb(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20); -#endif - - /* - * Program tlb entries for this size (dynamic) - */ - program_tlb(0, CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20, - MY_TLB_WORD2_I_ENABLE); - -#if defined(CONFIG_DDR_ECC) -#if defined(CONFIG_4xx_DCACHE) - /* - * If ECC is enabled, initialize the parity bits. - */ - program_ecc(0, CONFIG_SYS_MBYTES_SDRAM << 20, 0); -#else /* CONFIG_4xx_DCACHE */ - /* - * Setup 2nd TLB with same physical address but different virtual address - * with cache enabled. This is done for fast ECC generation. - */ - program_tlb(0, CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20, 0); - - /* - * If ECC is enabled, initialize the parity bits. - */ - program_ecc(CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20, 0); - - /* - * Now after initialization (auto-calibration and ECC generation) - * remove the TLB entries with caches enabled and program again with - * desired cache functionality - */ - remove_tlb(CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20); -#endif /* CONFIG_4xx_DCACHE */ -#endif /* CONFIG_DDR_ECC */ - - /* - * Clear possible errors resulting from data-eye-search. - * If not done, then we could get an interrupt later on when - * exceptions are enabled. - */ - set_mcsr(get_mcsr()); -#endif /* CONFIG_SPL_BUILD */ - - return (CONFIG_SYS_MBYTES_SDRAM << 20); -} diff --git a/configs/lcd4_lwmon5_defconfig b/configs/lcd4_lwmon5_defconfig deleted file mode 100644 index b911dbd..0000000 --- a/configs/lcd4_lwmon5_defconfig +++ /dev/null @@ -1,6 +0,0 @@ -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_LWMON5=y -CONFIG_SPL=y -CONFIG_SYS_EXTRA_OPTIONS="LCD4_LWMON5" -# CONFIG_CMD_SETEXPR is not set diff --git a/configs/lwmon5_defconfig b/configs/lwmon5_defconfig deleted file mode 100644 index 0a6da68..0000000 --- a/configs/lwmon5_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_LWMON5=y -# CONFIG_CMD_SETEXPR is not set diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 87e2b35..2697451 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +lwmon5 powerpc ppc4xx - - Stefan Roese sr@denx.de csb272/csb472 powerpc ppc4xx - - Tolunay Orkun torkun@nextio.com alpr powerpc ppc4xx - - Stefan Roese sr@denx.de cam_enc_4xx arm arm926ejs 8d775763 2015-08-20 Heiko Schocher hs@denx.de diff --git a/drivers/video/mb862xx.c b/drivers/video/mb862xx.c index 1c74e97..868c512 100644 --- a/drivers/video/mb862xx.c +++ b/drivers/video/mb862xx.c @@ -419,8 +419,7 @@ void *video_hw_init (void) board_disp_init (); #endif
-#if (defined(CONFIG_LWMON5) || \ - defined(CONFIG_SOCRATES)) && !(CONFIG_POST & CONFIG_SYS_POST_SYSMON) +#if defined(CONFIG_SOCRATES) && !(CONFIG_POST & CONFIG_SYS_POST_SYSMON) /* Lamp on */ board_backlight_switch (1); #endif diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h deleted file mode 100644 index 513167e..0000000 --- a/include/configs/lwmon5.h +++ /dev/null @@ -1,692 +0,0 @@ -/* - * (C) Copyright 2007-2013 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * lwmon5.h - configuration for lwmon5 board - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Liebherr extra version info - */ -#define CONFIG_IDENT_STRING " - v2.0" - -/* - * High Level Configuration Options - */ -#define CONFIG_LWMON5 1 /* Board is lwmon5 */ -#define CONFIG_440EPX 1 /* Specific PPC440EPx */ -#define CONFIG_440 1 /* ... PPC440 family */ - -#ifdef CONFIG_LCD4_LWMON5 -#define CONFIG_SYS_TEXT_BASE 0x01000000 /* SPL U-Boot TEXT_BASE */ -#define CONFIG_HOSTNAME lcd4_lwmon5 -#else -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 -#define CONFIG_HOSTNAME lwmon5 -#endif - -#define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ - -#define CONFIG_4xx_DCACHE /* enable cache in SDRAM */ - -#define CONFIG_BOARD_EARLY_INIT_F /* Call board_early_init_f */ -#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r */ -#define CONFIG_BOARD_POSTCLK_INIT /* Call board_postclk_init */ -#define CONFIG_MISC_INIT_R /* Call misc_init_r */ -#define CONFIG_BOARD_RESET /* Call board_reset */ - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of U-Boot */ -#define CONFIG_SYS_MONITOR_LEN 0x80000 -#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* Reserved for malloc */ - -#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ -#define CONFIG_SYS_LIME_BASE_0 0xc0000000 -#define CONFIG_SYS_LIME_BASE_1 0xc1000000 -#define CONFIG_SYS_LIME_BASE_2 0xc2000000 -#define CONFIG_SYS_LIME_BASE_3 0xc3000000 -#define CONFIG_SYS_FPGA_BASE_0 0xc4000000 -#define CONFIG_SYS_FPGA_BASE_1 0xc4200000 -#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ -#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PCI_MEMBASE1 (CONFIG_SYS_PCI_MEMBASE + 0x10000000) -#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE1 + 0x10000000) -#define CONFIG_SYS_PCI_MEMBASE3 (CONFIG_SYS_PCI_MEMBASE2 + 0x10000000) - -#ifndef CONFIG_LCD4_LWMON5 -#define CONFIG_SYS_USB2D0_BASE 0xe0000100 -#define CONFIG_SYS_USB_DEVICE 0xe0000000 -#define CONFIG_SYS_USB_HOST 0xe0000400 -#endif - -/* - * Initial RAM & stack pointer - * - * On LWMON5 we use D-cache as init-ram and stack pointer. We also move - * the POST_WORD from OCM to a 440EPx register that preserves it's - * content during reset (GPT0_COMP6). This way we reserve the OCM (16k) - * for logbuffer only. (GPT0_COMP1-COMP5 are reserved for logbuffer header.) - */ -#ifndef CONFIG_LCD4_LWMON5 -#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#else -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) -#endif -/* unused GPT0 COMP reg */ -#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) -#define CONFIG_SYS_OCM_SIZE (16 << 10) -/* 440EPx errata CHIP 11: don't use last 4kbytes */ -#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) - -/* Additional registers for watchdog timer post test */ -#define CONFIG_SYS_WATCHDOG_TIME_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK2) -#define CONFIG_SYS_WATCHDOG_FLAGS_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK1) -#define CONFIG_SYS_DSPIC_TEST_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR -#define CONFIG_SYS_OCM_STATUS_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR -#define CONFIG_SYS_WATCHDOG_MAGIC 0x12480000 -#define CONFIG_SYS_WATCHDOG_MAGIC_MASK 0xFFFF0000 -#define CONFIG_SYS_DSPIC_TEST_MASK 0x00000001 -#define CONFIG_SYS_OCM_STATUS_OK 0x00009A00 -#define CONFIG_SYS_OCM_STATUS_FAIL 0x0000A300 -#define CONFIG_SYS_OCM_STATUS_MASK 0x0000FF00 - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 2 /* Use UART1 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */ -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */ - -/* - * FLASH related - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CONFIG_SYS_FLASH0 0xFC000000 -#define CONFIG_SYS_FLASH1 0xF8000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } - -#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION /* use hardware flash protection */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST /* don't warn upon unknown flash */ - -#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN) - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * DDR SDRAM - */ -#define CONFIG_SYS_MBYTES_SDRAM 256 -#define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */ -#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ -#ifndef CONFIG_LCD4_LWMON5 -#define CONFIG_DDR_ECC /* enable ECC */ -#endif - -#ifndef CONFIG_LCD4_LWMON5 -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_ECC | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_FPU | \ - CONFIG_SYS_POST_I2C | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_OCM | \ - CONFIG_SYS_POST_RTC | \ - CONFIG_SYS_POST_SPR | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_SYSMON | \ - CONFIG_SYS_POST_WATCHDOG | \ - CONFIG_SYS_POST_DSP | \ - CONFIG_SYS_POST_BSPEC1 | \ - CONFIG_SYS_POST_BSPEC2 | \ - CONFIG_SYS_POST_BSPEC3 | \ - CONFIG_SYS_POST_BSPEC4 | \ - CONFIG_SYS_POST_BSPEC5) - -/* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ - CONFIG_SYS_NS16550_COM2 } - -#define CONFIG_POST_UART { \ - "UART test", \ - "uart", \ - "This test verifies the UART operation.", \ - POST_RAM | POST_SLOWTEST | POST_ALWAYS | POST_MANUAL, \ - &uart_post_test, \ - NULL, \ - NULL, \ - CONFIG_SYS_POST_UART \ - } - -#define CONFIG_POST_WATCHDOG { \ - "Watchdog timer test", \ - "watchdog", \ - "This test checks the watchdog timer.", \ - POST_RAM | POST_POWERON | POST_SLOWTEST | POST_MANUAL | POST_REBOOT, \ - &lwmon5_watchdog_post_test, \ - NULL, \ - NULL, \ - CONFIG_SYS_POST_WATCHDOG \ - } - -#define CONFIG_POST_BSPEC1 { \ - "dsPIC init test", \ - "dspic_init", \ - "This test returns result of dsPIC READY test run earlier.", \ - POST_RAM | POST_ALWAYS, \ - &dspic_init_post_test, \ - NULL, \ - NULL, \ - CONFIG_SYS_POST_BSPEC1 \ - } - -#define CONFIG_POST_BSPEC2 { \ - "dsPIC test", \ - "dspic", \ - "This test gets result of dsPIC POST and dsPIC version.", \ - POST_RAM | POST_ALWAYS, \ - &dspic_post_test, \ - NULL, \ - NULL, \ - CONFIG_SYS_POST_BSPEC2 \ - } - -#define CONFIG_POST_BSPEC3 { \ - "FPGA test", \ - "fpga", \ - "This test checks FPGA registers and memory.", \ - POST_RAM | POST_ALWAYS | POST_MANUAL, \ - &fpga_post_test, \ - NULL, \ - NULL, \ - CONFIG_SYS_POST_BSPEC3 \ - } - -#define CONFIG_POST_BSPEC4 { \ - "GDC test", \ - "gdc", \ - "This test checks GDC registers and memory.", \ - POST_RAM | POST_ALWAYS | POST_MANUAL,\ - &gdc_post_test, \ - NULL, \ - NULL, \ - CONFIG_SYS_POST_BSPEC4 \ - } - -#define CONFIG_POST_BSPEC5 { \ - "SYSMON1 test", \ - "sysmon1", \ - "This test checks GPIO_62_EPX pin indicating power failure.", \ - POST_RAM | POST_MANUAL | POST_NORMAL | POST_SLOWTEST, \ - &sysmon1_post_test, \ - NULL, \ - NULL, \ - CONFIG_SYS_POST_BSPEC5 \ - } - -#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ -#define CONFIG_LOGBUFFER -/* Reserve GPT0_COMP1-COMP5 for logbuffer header */ -#define CONFIG_ALT_LH_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP1) -#define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE) -#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -#endif - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* RTC */ -#define CONFIG_SYS_I2C_EEPROM_CPU_ADDR 0x52 /* EEPROM (CPU Modul) */ -#define CONFIG_SYS_I2C_EEPROM_MB_ADDR 0x53 /* EEPROM AT24C128 (MainBoard) */ -#define CONFIG_SYS_I2C_DSPIC_ADDR 0x54 /* dsPIC */ -#define CONFIG_SYS_I2C_DSPIC_2_ADDR 0x55 /* dsPIC */ -#define CONFIG_SYS_I2C_DSPIC_KEYB_ADDR 0x56 /* dsPIC */ -#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* dsPIC */ - -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ - /* 64 byte page write mode using*/ - /* last 6 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE - -#define CONFIG_RTC_PCF8563 /* enable Philips PCF8563 RTC */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ -#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ -#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ - -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_EEPROM_CPU_ADDR,\ - CONFIG_SYS_I2C_EEPROM_MB_ADDR, \ - CONFIG_SYS_I2C_DSPIC_ADDR, \ - CONFIG_SYS_I2C_DSPIC_2_ADDR, \ - CONFIG_SYS_I2C_DSPIC_KEYB_ADDR,\ - CONFIG_SYS_I2C_DSPIC_IO_ADDR } - -/* - * Pass open firmware flat tree - */ -#define CONFIG_OF_LIBFDT -#define CONFIG_OF_BOARD_SETUP -/* Update size in "reg" property of NOR FLASH device tree nodes */ -#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE - -#define CONFIG_FIT /* enable FIT image support */ - -#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ - -#define CONFIG_PREBOOT "setenv bootdelay 15" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "hostname=lwmon5\0" \ - "netdev=eth0\0" \ - "unlock=yes\0" \ - "logversion=2\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ - "addmisc=setenv bootargs ${bootargs} rtc-pcf8563.probe=0,0x51\0"\ - "flash_nfs=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};" \ - "run nfsargs addip addtty addmisc;bootm\0" \ - "rootpath=/opt/eldk/ppc_4xxFP\0" \ - "bootfile=/tftpboot/lwmon5/uImage\0" \ - "kernel_addr=FC000000\0" \ - "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ - "update=protect off FFF80000 FFFFFFFF;era FFF80000 FFFFFFFF;" \ - "cp.b 200000 FFF80000 80000\0" \ - "upd=run load update\0" \ - "lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \ - "autoscr 200000\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 3 /* PHY address, See schematics */ - -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_PHY_RESET_DELAY 300 - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#define CONFIG_PHY1_ADDR 1 - -/* Video console */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_MB862xx -#define CONFIG_VIDEO_MB862xx_ACCEL -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -#define CONFIG_CONSOLE_EXTRA_INFO -#define VIDEO_FB_16BPP_PIXEL_SWAP -#define VIDEO_FB_16BPP_WORD_SWAP - -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_SPLASH_SCREEN - -#ifndef CONFIG_LCD4_LWMON5 -/* - * USB/EHCI - */ -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_PPC4XX /* on PPC4xx platform */ -#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 -#define CONFIG_EHCI_MMIO_BIG_ENDIAN -#define CONFIG_EHCI_DESC_BIG_ENDIAN -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* re-init HCD after CMD_RESET */ -#define CONFIG_USB_STORAGE - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#endif - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SDRAM - -#ifdef CONFIG_VIDEO -#define CONFIG_CMD_BMP -#endif - -#ifndef CONFIG_LCD4_LWMON5 -#ifdef CONFIG_440EPX -#define CONFIG_CMD_USB -#endif -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SUPPORT_VFAT - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/ - -#ifndef CONFIG_LCD4_LWMON5 -#ifndef DEBUG -#define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */ -#endif -#define CONFIG_WD_PERIOD 40000 /* in usec */ -#define CONFIG_WD_MAX_RATE 66600 /* in ticks */ -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 16 MB of memory, since this is - * the maximum mapped by the 40x Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ - -/* - * External Bus Controller (EBC) Setup - */ -#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE - -/* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x03000280 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xfc000) - -/* Memory Bank 1 (Lime) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x01004380 -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xbc000) - -/* Memory Bank 2 (FPGA) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x01004400 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE_0 | 0x1c000) - -/* Memory Bank 3 (FPGA2) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x01004400 -#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FPGA_BASE_1 | 0x1c000) - -#define CONFIG_SYS_EBC_CFG 0xb8400000 - -/* - * Graphics (Fujitsu Lime) - */ -/* SDRAM Clock frequency adjustment register */ -#define CONFIG_SYS_LIME_SDRAM_CLOCK 0xC1FC0038 -#if 1 /* 133MHz is not tested enough, use 100MHz for now */ -/* Lime Clock frequency is to set 100MHz */ -#define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000 -#else -/* Lime Clock frequency for 133MHz */ -#define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000 -#endif - -/* SDRAM Parameter register */ -#define CONFIG_SYS_LIME_MMR 0xC1FCFFFC -/* - * SDRAM parameter value; was 0x414FB7F2, caused several vertical bars - * and pixel flare on display when 133MHz was configured. According to - * SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed - * Grade - */ -#ifdef CONFIG_SYS_LIME_CLOCK_133MHZ -#define CONFIG_SYS_MB862xx_MMR 0x414FB7F3 -#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_133MHZ -#else -#define CONFIG_SYS_MB862xx_MMR 0x414FB7F2 -#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_100MHZ -#endif - -/* - * GPIO Setup - */ -#define CONFIG_SYS_GPIO_PHY1_RST 12 -#define CONFIG_SYS_GPIO_FLASH_WP 14 -#define CONFIG_SYS_GPIO_PHY0_RST 22 -#define CONFIG_SYS_GPIO_PERM_VOLT_FEED 49 -#define CONFIG_SYS_GPIO_DSPIC_READY 51 -#define CONFIG_SYS_GPIO_CAN_ENABLE 53 -#define CONFIG_SYS_GPIO_LSB_ENABLE 54 -#define CONFIG_SYS_GPIO_EEPROM_EXT_WP 55 -#define CONFIG_SYS_GPIO_HIGHSIDE 56 -#define CONFIG_SYS_GPIO_EEPROM_INT_WP 57 -#define CONFIG_SYS_GPIO_BOARD_RESET 58 -#define CONFIG_SYS_GPIO_LIME_S 59 -#define CONFIG_SYS_GPIO_LIME_RST 60 -#define CONFIG_SYS_GPIO_SYSMON_STATUS 62 -#define CONFIG_SYS_GPIO_WATCHDOG 63 - -/* On LCD4, GPIO49 has to be configured to 0 instead of 1 */ -#ifdef CONFIG_LCD4_LWMON5 -#define GPIO49_VAL 0 -#else -#define GPIO49_VAL 1 -#endif - -/* - * PPC440 GPIO Configuration - */ -#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ -{ \ -/* GPIO Core 0 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO15 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMCTxD(4) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMCTxD(5) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMCTxD(6) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMCTxD(7) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 GMCTxD(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 GMCTxD(3) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \ -}, \ -{ \ -/* GPIO Core 1 */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO49_VAL}, /* GPIO49 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO57 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \ -} \ -} - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * SPL related defines - */ -#ifdef CONFIG_LCD4_LWMON5 -#define CONFIG_SPL_FRAMEWORK -#define CONFIG_SPL_BOARD_INIT -#define CONFIG_SPL_NOR_SUPPORT -#define CONFIG_SPL_TEXT_BASE 0xffff0000 /* last 64 KiB for SPL */ -#define CONFIG_SYS_SPL_MAX_LEN (64 << 10) -#define CONFIG_UBOOT_PAD_TO 458752 /* decimal for 'dd' */ -#define CONFIG_SPL_LIBCOMMON_SUPPORT /* image.c */ -#define CONFIG_SPL_LIBGENERIC_SUPPORT /* string.c */ -#define CONFIG_SPL_SERIAL_SUPPORT - -/* Place BSS for SPL near end of SDRAM */ -#define CONFIG_SPL_BSS_START_ADDR ((256 - 1) << 20) -#define CONFIG_SPL_BSS_MAX_SIZE (64 << 10) - -#define CONFIG_SPL_OS_BOOT -/* Place patched DT blob (fdt) at this address */ -#define CONFIG_SYS_SPL_ARGS_ADDR 0x01800000 - -#define CONFIG_SPL_TARGET "u-boot-img-spl-at-end.bin" - -/* Settings for real U-Boot to be loaded from NOR flash */ -#define CONFIG_SYS_UBOOT_BASE (-CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_UBOOT_START 0x01002100 - -#define CONFIG_SYS_OS_BASE 0xf8000000 -#define CONFIG_SYS_FDT_BASE 0xf87c0000 -#endif - -#endif /* __CONFIG_H */