Update all A83T devicetree dtsi and dtsi files from Linux with below commit: commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6 Author: Mylène Josserand mylene.josserand@bootlin.com Date: Fri May 4 21:05:44 2018 +0200
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
Note: bananapi-m3 and cubietruck-plus board dts files has usb_otg enabled in U-Boot which were not present in Linux.
Signed-off-by: Jagan Teki jagan@amarulasolutions.com --- arch/arm/dts/axp81x.dtsi | 169 ++++ .../dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 195 +++- arch/arm/dts/sun8i-a83t-bananapi-m3.dts | 298 +++++- arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 322 ++++++- arch/arm/dts/sun8i-a83t-tbs-a711.dts | 355 ++++++- arch/arm/dts/sun8i-a83t.dtsi | 885 ++++++++++++++++-- include/dt-bindings/clock/sun8i-a83t-ccu.h | 140 +++ include/dt-bindings/reset/sun8i-a83t-ccu.h | 98 ++ 8 files changed, 2382 insertions(+), 80 deletions(-) create mode 100644 arch/arm/dts/axp81x.dtsi create mode 100644 include/dt-bindings/clock/sun8i-a83t-ccu.h create mode 100644 include/dt-bindings/reset/sun8i-a83t-ccu.h
diff --git a/arch/arm/dts/axp81x.dtsi b/arch/arm/dts/axp81x.dtsi new file mode 100644 index 0000000000..043c717dce --- /dev/null +++ b/arch/arm/dts/axp81x.dtsi @@ -0,0 +1,169 @@ +/* + * Copyright 2017 Chen-Yu Tsai + * + * Chen-Yu Tsai wens@csie.org + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* AXP813/818 Integrated Power Management Chip */ + +&axp81x { + interrupt-controller; + #interrupt-cells = <1>; + + axp_adc: adc { + compatible = "x-powers,axp813-adc"; + #io-channel-cells = <1>; + }; + + axp_gpio: gpio { + compatible = "x-powers,axp813-gpio"; + gpio-controller; + #gpio-cells = <2>; + + gpio0_ldo: gpio0-ldo { + pins = "GPIO0"; + function = "ldo"; + }; + + gpio1_ldo: gpio1-ldo { + pins = "GPIO1"; + function = "ldo"; + }; + }; + + battery_power_supply: battery-power-supply { + compatible = "x-powers,axp813-battery-power-supply"; + status = "disabled"; + }; + + regulators { + /* Default work frequency for buck regulators */ + x-powers,dcdc-freq = <3000>; + + reg_dcdc1: dcdc1 { + }; + + reg_dcdc2: dcdc2 { + }; + + reg_dcdc3: dcdc3 { + }; + + reg_dcdc4: dcdc4 { + }; + + reg_dcdc5: dcdc5 { + }; + + reg_dcdc6: dcdc6 { + }; + + reg_dcdc7: dcdc7 { + }; + + reg_aldo1: aldo1 { + }; + + reg_aldo2: aldo2 { + }; + + reg_aldo3: aldo3 { + }; + + reg_dldo1: dldo1 { + }; + + reg_dldo2: dldo2 { + }; + + reg_dldo3: dldo3 { + }; + + reg_dldo4: dldo4 { + }; + + reg_eldo1: eldo1 { + }; + + reg_eldo2: eldo2 { + }; + + reg_eldo3: eldo3 { + }; + + reg_fldo1: fldo1 { + }; + + reg_fldo2: fldo2 { + }; + + reg_fldo3: fldo3 { + }; + + reg_ldo_io0: ldo-io0 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio0_ldo>; + /* Disable by default to avoid conflicts with GPIO */ + status = "disabled"; + }; + + reg_ldo_io1: ldo-io1 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio1_ldo>; + /* Disable by default to avoid conflicts with GPIO */ + status = "disabled"; + }; + + reg_rtc_ldo: rtc-ldo { + /* RTC_LDO is a fixed, always-on regulator */ + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_sw: sw { + }; + + reg_drivevbus: drivevbus { + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts index c8495d7624..36ecebaff3 100644 --- a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts +++ b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts @@ -44,6 +44,8 @@ /dts-v1/; #include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h> + / { model = "Allwinner A83T H8Homlet Proto Dev Board v2.0"; compatible = "allwinner,h8homlet-v2", "allwinner,sun8i-a83t"; @@ -55,22 +57,213 @@ chosen { stdout-path = "serial0:115200n8"; }; + + reg_usb0_vbus: reg-usb0-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ + }; + + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; };
&ehci0 { status = "okay"; };
+&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_emmc_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + &ohci0 { status = "okay"; };
+&r_rsb { + status = "okay"; + + axp81x: pmic@3a3 { + compatible = "x-powers,axp818", "x-powers,axp813"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + swin-supply = <®_dcdc1>; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; + }; + }; +}; + +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-mipi"; +}; + +®_dldo4 { + /* + * The PHY requires 20ms after all voltages are applied until core + * logic is ready and 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-ephy"; +}; + +®_fldo1 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +®_sw { + regulator-name = "vcc-wifi"; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_b>; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usbphy { + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; status = "okay"; };
&usb_otg { + dr_mode = "host"; status = "okay"; }; diff --git a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts index dfc16a0272..eaff6fa401 100644 --- a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts +++ b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts @@ -1,6 +1,7 @@ /* - * Copyright 2015 Vishnu Patekar - * Vishnu Patekar vishnupatekar0510@gmail.com + * Copyright 2017 Chen-Yu Tsai + * + * Chen-Yu Tsai wens@csie.org * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -44,29 +45,316 @@ /dts-v1/; #include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h> + / { - model = "Allwinner A83T BananaPi M3 Board v1.2"; - compatible = "bananapi,m3v1.2", "allwinner,sun8i-a83t"; + model = "Banana Pi BPI-M3"; + compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
aliases { + ethernet0 = &emac; serial0 = &uart0; };
chosen { stdout-path = "serial0:115200n8"; }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + blue { + label = "bananapi-m3:blue:usr"; + gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; + }; + + green { + label = "bananapi-m3:green:usr"; + gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; + }; + }; + + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* The WiFi low power clock must be 32768 Hz */ + assigned-clocks = <&ac100_rtc 1>; + assigned-clock-rates = <32768>; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; +}; + +&de { + status = "okay"; };
&ehci0 { + /* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */ status = "okay"; + + /* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */ +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_sw>; + phy-handle = <&rgmii_phy>; + phy-mode = "rgmii"; + allwinner,rx-delay-ps = <700>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + +&mmc1 { + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_emmc_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp81x: pmic@3a3 { + compatible = "x-powers,axp813"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + fldoin-supply = <®_dcdc5>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; + }; + }; +}; + +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + /* schematics says 3.1V but FEX file says 3.3V */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + /* + * This powers both the WiFi/BT module's main power, I/O supply, + * and external pull-ups on all the data lines. It should be set + * to the same voltage as the I/O supply (DCDC1 in this case) to + * avoid any leakage or mismatch. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pd"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +®_fldo1 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +®_sw { + /* + * The PHY requires 20ms after all voltages + * are applied until core logic is ready and + * 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC + * ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-name = "vcc-ephy"; };
&uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_b>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; };
&usb_otg { status = "okay"; }; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts index 8437c8f59e..5dba4fc310 100644 --- a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts +++ b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts @@ -45,33 +45,353 @@ /dts-v1/; #include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h> + / { model = "Cubietech Cubietruck Plus"; compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
aliases { + ethernet0 = &emac; serial0 = &uart0; };
chosen { stdout-path = "serial0:115200n8"; }; + + leds { + compatible = "gpio-leds"; + + blue { + label = "cubietruck-plus:blue:usr"; + gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */ + }; + + orange { + label = "cubietruck-plus:orange:usr"; + gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */ + }; + + white { + label = "cubietruck-plus:white:usr"; + gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */ + }; + + green { + label = "cubietruck-plus:green:usr"; + gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */ + }; + }; + + usb-hub { + /* I2C is not connected */ + compatible = "smsc,usb3503"; + initial-mode = <1>; /* initialize in HUB mode */ + disabled-ports = <1>; + intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */ + connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */ + refclk-frequency = <19200000>; + }; + + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */ + }; + + reg_usb2_vbus: reg-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb2-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "On-board SPDIF"; + + simple-audio-card,cpu { + sound-dai = <&spdif>; + }; + + simple-audio-card,codec { + sound-dai = <&spdif_out>; + }; + }; + + spdif_out: spdif-out { + #sound-dai-cells = <0>; + compatible = "linux,spdif-dit"; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* The WiFi low power clock must be 32768 Hz */ + assigned-clocks = <&ac100_rtc 1>; + assigned-clock-rates = <32768>; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; };
&ehci0 { + /* GL830 USB-to-SATA bridge here */ status = "okay"; };
&ehci1 { + /* USB3503 HSIC USB 2.0 hub here */ + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_dldo4>; + phy-handle = <&rgmii_phy>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&mdio { + rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + +&mmc1 { + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_sw>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_emmc_pins>; + vmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp81x: pmic@3a3 { + compatible = "x-powers,axp818", "x-powers,axp813"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; + }; + }; +}; + +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + /* + * The schematics say this should be 3.3V, but the FEX file says + * it should be 3V. The latter makes sense, as the WiFi module's + * I/O is indirectly powered from DCDC1, through SW. It is rated + * at 2.98V maximum. + */ + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "dp-pwr"; +}; + +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "ephy-io"; +}; + +®_dldo4 { + /* + * The PHY requires 20ms after all voltages are applied until core + * logic is ready and 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "ephy"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dp-bridge-1"; +}; + +®_eldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dp-bridge-2"; +}; + +®_fldo1 { + /* TODO should be handled by USB PHY */ + regulator-always-on; + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +®_sw { + regulator-name = "vcc-wifi-io"; +}; + +&spdif { status = "okay"; };
&uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_b>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; };
&usb_otg { status = "okay"; }; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/dts/sun8i-a83t-tbs-a711.dts index 80e8b1cc90..1537ce148c 100644 --- a/arch/arm/dts/sun8i-a83t-tbs-a711.dts +++ b/arch/arm/dts/sun8i-a83t-tbs-a711.dts @@ -1,6 +1,6 @@ /* - * Copyright 2017 Ondřej Jirman - * Ondřej Jirman megous@megous.com + * Copyright (C) 2017 Touchless Biometric Systems AG + * Tomas Novotny tomas@novotny.cz * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -44,33 +44,380 @@ /dts-v1/; #include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pwm/pwm.h> + / { model = "TBS A711 Tablet"; compatible = "tbs-biometrics,a711", "allwinner,sun8i-a83t";
aliases { serial0 = &uart0; + serial1 = &uart1; };
chosen { stdout-path = "serial0:115200n8"; }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + enable-gpios = <&pio 3 29 GPIO_ACTIVE_HIGH>; + + brightness-levels = <0 1 2 4 8 16 32 64 128 255>; + default-brightness-level = <9>; + }; + + panel { + compatible = "tbs,a711-panel", "panel-lvds"; + backlight = <&backlight>; + power-supply = <®_sw>; + + width-mm = <153>; + height-mm = <90>; + data-mapping = "vesa-24"; + + panel-timing { + /* 1024x600 @60Hz */ + clock-frequency = <52000000>; + hactive = <1024>; + vactive = <600>; + hsync-len = <20>; + hfront-porch = <180>; + hback-porch = <160>; + vfront-porch = <12>; + vback-porch = <23>; + vsync-len = <5>; + }; + + port { + panel_input: endpoint { + remote-endpoint = <&tcon0_out_lcd>; + }; + }; + }; + + reg_vbat: reg-vbat { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + reg_vmain: reg-vmain { + compatible = "regulator-fixed"; + regulator-name = "vmain"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <®_vbat>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + + /* + * This is actually Bluetooth's clock, but we have to + * hook it up somewheere + */ + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&cpu100 { + cpu-supply = <®_dcdc3>; +}; + +&de { + status = "okay"; };
+/* + * An USB-2 hub is connected here, which also means we don't need to + * enable the OHCI controller. + */ &ehci0 { status = "okay"; };
-&ohci0 { +/* + * There's a modem connected here that needs to be initialised before + * being able to be enumerated. + */ +&ehci1 { + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_dcdc1>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&mmc1 { + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_dldo1>; + non-removable; + wakeup-source; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 WL_WAKE_UP */ + interrupt-names = "host-wake"; + }; +}; + +&mmc2 { + pinctrl-0 = <&mmc2_8bit_emmc_pins>; + pinctrl-names = "default"; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pin>; + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp81x: pmic@3a3 { + compatible = "x-powers,axp813"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 12 IRQ_TYPE_LEVEL_LOW>; /* PL12 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; + }; + }; + +}; + +#include "axp81x.dtsi" + +&battery_power_supply { + status = "okay"; +}; + +®_aldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1.8"; +}; + +®_aldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-name = "vdd-drampll"; +}; + +®_aldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-name = "avcc"; +}; + +®_dcdc1 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + regulator-name = "vcc-io"; +}; + +®_dcdc2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-name = "vdd-cpu-A"; +}; + +®_dcdc3 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-name = "vdd-cpu-B"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-wifi-io"; +}; + +®_dldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <4200000>; + regulator-name = "vcc-mipi"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; status = "okay"; };
+®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-csi-r"; +}; + +®_eldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-dsi"; +}; + +®_eldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-csi-f"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-hsic"; +}; + +®_fldo2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-ctp"; + status = "okay"; +}; + +®_ldo_io1 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-vb"; + status = "okay"; +}; + +®_sw { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-lcd"; +}; + +&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd_lvds_pins>; +}; + +&tcon0_out { + tcon0_out_lcd: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_b>; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +/* There's the BT part of the AP6210 connected to that UART */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; status = "okay"; };
&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus_supply = <®_vmain>; + usb2_vbus_supply = <®_vmain>; status = "okay"; }; diff --git a/arch/arm/dts/sun8i-a83t.dtsi b/arch/arm/dts/sun8i-a83t.dtsi index 2953e0fdac..2be23d6009 100644 --- a/arch/arm/dts/sun8i-a83t.dtsi +++ b/arch/arm/dts/sun8i-a83t.dtsi @@ -40,67 +40,99 @@ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR * OTHER DEALINGS IN THE SOFTWARE. - */
-#include "skeleton.dtsi" - #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h> +#include <dt-bindings/clock/sun8i-a83t-ccu.h> +#include <dt-bindings/clock/sun8i-de2.h> +#include <dt-bindings/clock/sun8i-r-ccu.h> +#include <dt-bindings/reset/sun8i-a83t-ccu.h> +#include <dt-bindings/reset/sun8i-de2.h> +#include <dt-bindings/reset/sun8i-r-ccu.h>
/ { interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <1>;
cpus { #address-cells = <1>; #size-cells = <0>;
- cpu@0 { + cpu0: cpu@0 { + clocks = <&ccu CLK_C0CPUX>; + clock-names = "cpu"; compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0>; };
cpu@1 { compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <1>; };
cpu@2 { compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <2>; };
cpu@3 { compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <3>; };
- cpu@100 { + cpu100: cpu@100 { + clocks = <&ccu CLK_C1CPUX>; + clock-names = "cpu"; compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x100>; };
cpu@101 { compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x101>; };
cpu@102 { compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x102>; };
cpu@103 { compatible = "arm,cortex-a7"; device_type = "cpu"; + operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x103>; }; }; @@ -123,6 +155,7 @@ #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <24000000>; + clock-accuracy = <50000>; clock-output-names = "osc24M"; };
@@ -148,48 +181,575 @@ }; };
+ de: display-engine { + compatible = "allwinner,sun8i-a83t-display-engine"; + allwinner,pipelines = <&mixer0>, <&mixer1>; + status = "disabled"; + }; + + memory { + reg = <0x40000000 0x80000000>; + device_type = "memory"; + }; + + cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2"; + opp-shared; + + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-864000000 { + opp-hz = /bits/ 64 <864000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-912000000 { + opp-hz = /bits/ 64 <912000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-1008000000 { + opp-hz = /bits/ 64 <1008000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-1128000000 { + opp-hz = /bits/ 64 <1128000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + }; + + cpu1_opp_table: opp_table1 { + compatible = "operating-points-v2"; + opp-shared; + + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-864000000 { + opp-hz = /bits/ 64 <864000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-912000000 { + opp-hz = /bits/ 64 <912000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-1008000000 { + opp-hz = /bits/ 64 <1008000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-1128000000 { + opp-hz = /bits/ 64 <1128000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <840000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + }; + soc { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges;
- pio: pinctrl@01c20800 { + display_clocks: clock@1000000 { + compatible = "allwinner,sun8i-a83t-de2-clk"; + reg = <0x01000000 0x100000>; + clocks = <&ccu CLK_PLL_DE>, + <&ccu CLK_BUS_DE>; + clock-names = "mod", + "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + mixer0: mixer@1100000 { + compatible = "allwinner,sun8i-a83t-de2-mixer-0"; + reg = <0x01100000 0x100000>; + clocks = <&display_clocks CLK_BUS_MIXER0>, + <&display_clocks CLK_MIXER0>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_MIXER0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + mixer0_out_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_in_mixer0>; + }; + }; + }; + }; + + mixer1: mixer@1200000 { + compatible = "allwinner,sun8i-a83t-de2-mixer-1"; + reg = <0x01200000 0x100000>; + clocks = <&display_clocks CLK_BUS_MIXER1>, + <&display_clocks CLK_MIXER1>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_WB>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer1_out: port@1 { + reg = <1>; + + mixer1_out_tcon1: endpoint { + remote-endpoint = <&tcon1_in_mixer1>; + }; + }; + }; + }; + + cpucfg@1700000 { + compatible = "allwinner,sun8i-a83t-cpucfg"; + reg = <0x01700000 0x400>; + }; + + cci@1790000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x01790000 0x10000>; + ranges = <0x0 0x01790000 0x10000>; + + cci_control0: slave-if@4000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x4000 0x1000>; + }; + + cci_control1: slave-if@5000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x5000 0x1000>; + }; + + pmu@9000 { + compatible = "arm,cci-400-pmu,r1"; + reg = <0x9000 0x5000>; + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + syscon: syscon@1c00000 { + compatible = "allwinner,sun8i-a83t-system-controller", + "syscon"; + reg = <0x01c00000 0x1000>; + }; + + dma: dma-controller@1c02000 { + compatible = "allwinner,sun8i-a83t-dma"; + reg = <0x01c02000 0x1000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_DMA>; + resets = <&ccu RST_BUS_DMA>; + #dma-cells = <1>; + }; + + tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun8i-a83t-tcon-lcd"; + reg = <0x01c0c000 0x1000>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>; + clock-names = "ahb", "tcon-ch0"; + clock-output-names = "tcon-pixel-clock"; + resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>; + reset-names = "lcd", "lvds"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_mixer0: endpoint@0 { + reg = <0>; + remote-endpoint = <&mixer0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; + }; + + tcon1: lcd-controller@1c0d000 { + compatible = "allwinner,sun8i-a83t-tcon-tv"; + reg = <0x01c0d000 0x1000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_TCON1>, <&ccu CLK_TCON1>; + clock-names = "ahb", "tcon-ch1"; + resets = <&ccu RST_BUS_TCON1>; + reset-names = "lcd"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon1_in: port@0 { + reg = <0>; + + tcon1_in_mixer1: endpoint { + remote-endpoint = <&mixer1_out_tcon1>; + }; + }; + + tcon1_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tcon1_out_hdmi: endpoint@1 { + reg = <1>; + remote-endpoint = <&hdmi_in_tcon1>; + }; + }; + }; + }; + + mmc0: mmc@1c0f000 { + compatible = "allwinner,sun8i-a83t-mmc", + "allwinner,sun7i-a20-mmc"; + reg = <0x01c0f000 0x1000>; + clocks = <&ccu CLK_BUS_MMC0>, + <&ccu CLK_MMC0>, + <&ccu CLK_MMC0_OUTPUT>, + <&ccu CLK_MMC0_SAMPLE>; + clock-names = "ahb", + "mmc", + "output", + "sample"; + resets = <&ccu RST_BUS_MMC0>; + reset-names = "ahb"; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc1: mmc@1c10000 { + compatible = "allwinner,sun8i-a83t-mmc", + "allwinner,sun7i-a20-mmc"; + reg = <0x01c10000 0x1000>; + clocks = <&ccu CLK_BUS_MMC1>, + <&ccu CLK_MMC1>, + <&ccu CLK_MMC1_OUTPUT>, + <&ccu CLK_MMC1_SAMPLE>; + clock-names = "ahb", + "mmc", + "output", + "sample"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@1c11000 { + compatible = "allwinner,sun8i-a83t-emmc"; + reg = <0x01c11000 0x1000>; + clocks = <&ccu CLK_BUS_MMC2>, + <&ccu CLK_MMC2>, + <&ccu CLK_MMC2_OUTPUT>, + <&ccu CLK_MMC2_SAMPLE>; + clock-names = "ahb", + "mmc", + "output", + "sample"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + sid: eeprom@1c14000 { + compatible = "allwinner,sun8i-a83t-sid"; + reg = <0x1c14000 0x400>; + }; + + usb_otg: usb@1c19000 { + compatible = "allwinner,sun8i-a83t-musb", + "allwinner,sun8i-a33-musb"; + reg = <0x01c19000 0x0400>; + clocks = <&ccu CLK_BUS_OTG>; + resets = <&ccu RST_BUS_OTG>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + status = "disabled"; + }; + + usbphy: phy@1c19400 { + compatible = "allwinner,sun8i-a83t-usb-phy"; + reg = <0x01c19400 0x10>, + <0x01c1a800 0x14>, + <0x01c1b800 0x14>; + reg-names = "phy_ctrl", + "pmu1", + "pmu2"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>, + <&ccu CLK_USB_HSIC>, + <&ccu CLK_USB_HSIC_12M>; + clock-names = "usb0_phy", + "usb1_phy", + "usb2_phy", + "usb2_hsic_12M"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_HSIC>; + reset-names = "usb0_reset", + "usb1_reset", + "usb2_reset"; + status = "disabled"; + #phy-cells = <1>; + }; + + ehci0: usb@1c1a000 { + compatible = "allwinner,sun8i-a83t-ehci", + "generic-ehci"; + reg = <0x01c1a000 0x100>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_EHCI0>; + resets = <&ccu RST_BUS_EHCI0>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci0: usb@1c1a400 { + compatible = "allwinner,sun8i-a83t-ohci", + "generic-ohci"; + reg = <0x01c1a400 0x100>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>; + resets = <&ccu RST_BUS_OHCI0>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ehci1: usb@1c1b000 { + compatible = "allwinner,sun8i-a83t-ehci", + "generic-ehci"; + reg = <0x01c1b000 0x100>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_EHCI1>; + resets = <&ccu RST_BUS_EHCI1>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + ccu: clock@1c20000 { + compatible = "allwinner,sun8i-a83t-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc16Md512>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + pio: pinctrl@1c20800 { compatible = "allwinner,sun8i-a83t-pinctrl"; interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; reg = <0x01c20800 0x400>; - clocks = <&osc24M>; + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc16Md512>; + clock-names = "apb", "hosc", "losc"; gpio-controller; interrupt-controller; #interrupt-cells = <3>; #gpio-cells = <3>;
- mmc0_pins_a: mmc0@0 { - allwinner,pins = "PF0", "PF1", "PF2", - "PF3", "PF4", "PF5"; - allwinner,function = "mmc0"; - allwinner,drive = <SUN4I_PINCTRL_30_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + emac_rgmii_pins: emac-rgmii-pins { + pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7", + "PD11", "PD12", "PD13", "PD14", "PD18", + "PD19", "PD21", "PD22", "PD23"; + function = "gmac"; + /* + * data lines in RGMII mode use DDR mode + * and need a higher signal drive strength + */ + drive-strength = <40>; + }; + + hdmi_pins: hdmi-pins { + pins = "PH6", "PH7", "PH8"; + function = "hdmi"; + }; + + i2c0_pins: i2c0-pins { + pins = "PH0", "PH1"; + function = "i2c0"; + }; + + i2c1_pins: i2c1-pins { + pins = "PH2", "PH3"; + function = "i2c1"; + }; + + i2c2_ph_pins: i2c2-ph-pins { + pins = "PH4", "PH5"; + function = "i2c2"; + }; + + i2s1_pins: i2s1-pins { + /* I2S1 does not have external MCLK pin */ + pins = "PG10", "PG11", "PG12", "PG13"; + function = "i2s1"; + }; + + lcd_lvds_pins: lcd-lvds-pins { + pins = "PD18", "PD19", "PD20", "PD21", "PD22", + "PD23", "PD24", "PD25", "PD26", "PD27"; + function = "lvds0"; + }; + + mmc0_pins: mmc0-pins { + pins = "PF0", "PF1", "PF2", + "PF3", "PF4", "PF5"; + function = "mmc0"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc1_pins: mmc1-pins { + pins = "PG0", "PG1", "PG2", + "PG3", "PG4", "PG5"; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc2_8bit_emmc_pins: mmc2-8bit-emmc-pins { + pins = "PC5", "PC6", "PC8", "PC9", + "PC10", "PC11", "PC12", "PC13", + "PC14", "PC15", "PC16"; + function = "mmc2"; + drive-strength = <30>; + bias-pull-up; + }; + + pwm_pin: pwm-pin { + pins = "PD28"; + function = "pwm"; + }; + + spdif_tx_pin: spdif-tx-pin { + pins = "PE18"; + function = "spdif"; + }; + + uart0_pb_pins: uart0-pb-pins { + pins = "PB9", "PB10"; + function = "uart0"; + }; + + uart0_pf_pins: uart0-pf-pins { + pins = "PF2", "PF4"; + function = "uart0"; };
- uart0_pins_a: uart0@0 { - allwinner,pins = "PF2", "PF4"; - allwinner,function = "uart0"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + uart1_pins: uart1-pins { + pins = "PG6", "PG7"; + function = "uart1"; };
- uart0_pins_b: uart0@1 { - allwinner,pins = "PB9", "PB10"; - allwinner,function = "uart0"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + uart1_rts_cts_pins: uart1-rts-cts-pins { + pins = "PG8", "PG9"; + function = "uart1"; }; };
- timer@01c20c00 { + timer@1c20c00 { compatible = "allwinner,sun4i-a10-timer"; reg = <0x01c20c00 0xa0>; interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, @@ -197,27 +757,166 @@ clocks = <&osc24M>; };
- watchdog@01c20ca0 { + watchdog@1c20ca0 { compatible = "allwinner,sun6i-a31-wdt"; reg = <0x01c20ca0 0x20>; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&osc24M>; };
- uart0: serial@01c28000 { + spdif: spdif@1c21000 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a83t-spdif", + "allwinner,sun8i-h3-spdif"; + reg = <0x01c21000 0x400>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>; + resets = <&ccu RST_BUS_SPDIF>; + clock-names = "apb", "spdif"; + dmas = <&dma 2>; + dma-names = "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&spdif_tx_pin>; + status = "disabled"; + }; + + i2s0: i2s@1c22000 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a83t-i2s"; + reg = <0x01c22000 0x400>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>; + clock-names = "apb", "mod"; + dmas = <&dma 3>, <&dma 3>; + resets = <&ccu RST_BUS_I2S0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2s1: i2s@1c22400 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a83t-i2s"; + reg = <0x01c22400 0x400>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>; + clock-names = "apb", "mod"; + dmas = <&dma 4>, <&dma 4>; + resets = <&ccu RST_BUS_I2S1>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s1_pins>; + status = "disabled"; + }; + + i2s2: i2s@1c22800 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a83t-i2s"; + reg = <0x01c22800 0x400>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>; + clock-names = "apb", "mod"; + dmas = <&dma 27>; + resets = <&ccu RST_BUS_I2S2>; + dma-names = "tx"; + status = "disabled"; + }; + + pwm: pwm@1c21400 { + compatible = "allwinner,sun8i-a83t-pwm", + "allwinner,sun8i-h3-pwm"; + reg = <0x01c21400 0x400>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; + }; + + uart0: serial@1c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&osc24M>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; status = "disabled"; };
- gic: interrupt-controller@01c81000 { + uart1: serial@1c28400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28400 0x400>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; + status = "disabled"; + }; + + i2c0: i2c@1c2ac00 { + compatible = "allwinner,sun8i-a83t-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@1c2b000 { + compatible = "allwinner,sun8i-a83t-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@1c2b400 { + compatible = "allwinner,sun8i-a83t-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + emac: ethernet@1c30000 { + compatible = "allwinner,sun8i-a83t-emac"; + syscon = <&syscon>; + reg = <0x01c30000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu 13>; + reset-names = "stmmaceth"; + clocks = <&ccu 27>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + gic: interrupt-controller@1c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>, - <0x01c82000 0x1000>, + <0x01c82000 0x2000>, <0x01c84000 0x2000>, <0x01c86000 0x2000>; interrupt-controller; @@ -225,59 +924,107 @@ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>; };
- usb_otg: usb@01c19000 { - compatible = "allwinner,sun8i-a33-musb"; - reg = <0x01c19000 0x400>; - interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "mc"; - phys = <&usbphy 0>; - phy-names = "usb"; + hdmi: hdmi@1ee0000 { + compatible = "allwinner,sun8i-a83t-dw-hdmi"; + reg = <0x01ee0000 0x10000>; + reg-io-width = <1>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>, + <&ccu CLK_HDMI>; + clock-names = "iahb", "isfr", "tmds"; + resets = <&ccu RST_BUS_HDMI1>; + reset-names = "ctrl"; + phys = <&hdmi_phy>; + phy-names = "hdmi-phy"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pins>; status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + hdmi_in: port@0 { + reg = <0>; + + hdmi_in_tcon1: endpoint { + remote-endpoint = <&tcon1_out_hdmi>; + }; + }; + + hdmi_out: port@1 { + reg = <1>; + }; + }; };
- usbphy: phy@1c19400 { - compatible = "allwinner,sun8i-a83t-usb-phy"; - reg = <0x01c19400 0x10>, - <0x01c1a800 0x14>, - <0x01c1b800 0x14>; - reg-names = "phy_ctrl", - "pmu1", - "pmu2"; - status = "disabled"; - #phy-cells = <1>; + hdmi_phy: hdmi-phy@1ef0000 { + compatible = "allwinner,sun8i-a83t-hdmi-phy"; + reg = <0x01ef0000 0x10000>; + clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_HDMI0>; + reset-names = "phy"; + #phy-cells = <0>; };
- ehci0: usb@01c1a000 { - compatible = "allwinner,sun8i-a83t-ehci", "generic-ehci"; - reg = <0x01c1a000 0x100>; - interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; - phys = <&usbphy 1>; - phy-names = "usb"; - status = "disabled"; + r_intc: interrupt-controller@1f00c00 { + compatible = "allwinner,sun8i-a83t-r-intc", + "allwinner,sun6i-a31-r-intc"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x01f00c00 0x400>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; };
- ohci0: usb@01c1a400 { - compatible = "allwinner,sun8i-a83t-ohci", "generic-ohci"; - reg = <0x01c1a400 0x100>; - interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; - phys = <&usbphy 1>; - phy-names = "usb"; - status = "disabled"; + r_ccu: clock@1f01400 { + compatible = "allwinner,sun8i-a83t-r-ccu"; + reg = <0x01f01400 0x400>; + clocks = <&osc24M>, <&osc16Md512>, <&osc16M>, + <&ccu 6>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; + #clock-cells = <1>; + #reset-cells = <1>; };
- ehci1: usb@01c1b000 { - compatible = "allwinner,sun8i-a83t-ehci", "generic-ehci"; - reg = <0x01c1b000 0x100>; - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - phys = <&usbphy 2>; - phy-names = "usb"; - status = "disabled"; + r_cpucfg@1f01c00 { + compatible = "allwinner,sun8i-a83t-r-cpucfg"; + reg = <0x1f01c00 0x400>; };
- r_pio: pinctrl@01f02c00 { + r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun8i-a83t-r-pinctrl"; reg = <0x01f02c00 0x400>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, + <&osc16Md512>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + + r_rsb_pins: r-rsb-pins { + pins = "PL0", "PL1"; + function = "s_rsb"; + drive-strength = <20>; + bias-pull-up; + }; + }; + + r_rsb: rsb@1f03400 { + compatible = "allwinner,sun8i-a83t-rsb", + "allwinner,sun8i-a23-rsb"; + reg = <0x01f03400 0x400>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_APB0_RSB>; + clock-frequency = <3000000>; + resets = <&r_ccu RST_APB0_RSB>; + pinctrl-names = "default"; + pinctrl-0 = <&r_rsb_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; }; }; }; diff --git a/include/dt-bindings/clock/sun8i-a83t-ccu.h b/include/dt-bindings/clock/sun8i-a83t-ccu.h new file mode 100644 index 0000000000..78af5085f6 --- /dev/null +++ b/include/dt-bindings/clock/sun8i-a83t-ccu.h @@ -0,0 +1,140 @@ +/* + * Copyright (C) 2017 Chen-Yu Tsai wens@csie.org + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_ +#define _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_ + +#define CLK_PLL_PERIPH 6 + +#define CLK_PLL_DE 9 + +#define CLK_C0CPUX 11 +#define CLK_C1CPUX 12 + +#define CLK_BUS_MIPI_DSI 19 +#define CLK_BUS_SS 20 +#define CLK_BUS_DMA 21 +#define CLK_BUS_MMC0 22 +#define CLK_BUS_MMC1 23 +#define CLK_BUS_MMC2 24 +#define CLK_BUS_NAND 25 +#define CLK_BUS_DRAM 26 +#define CLK_BUS_EMAC 27 +#define CLK_BUS_HSTIMER 28 +#define CLK_BUS_SPI0 29 +#define CLK_BUS_SPI1 30 +#define CLK_BUS_OTG 31 +#define CLK_BUS_EHCI0 32 +#define CLK_BUS_EHCI1 33 +#define CLK_BUS_OHCI0 34 + +#define CLK_BUS_VE 35 +#define CLK_BUS_TCON0 36 +#define CLK_BUS_TCON1 37 +#define CLK_BUS_CSI 38 +#define CLK_BUS_HDMI 39 +#define CLK_BUS_DE 40 +#define CLK_BUS_GPU 41 +#define CLK_BUS_MSGBOX 42 +#define CLK_BUS_SPINLOCK 43 + +#define CLK_BUS_SPDIF 44 +#define CLK_BUS_PIO 45 +#define CLK_BUS_I2S0 46 +#define CLK_BUS_I2S1 47 +#define CLK_BUS_I2S2 48 +#define CLK_BUS_TDM 49 + +#define CLK_BUS_I2C0 50 +#define CLK_BUS_I2C1 51 +#define CLK_BUS_I2C2 52 +#define CLK_BUS_UART0 53 +#define CLK_BUS_UART1 54 +#define CLK_BUS_UART2 55 +#define CLK_BUS_UART3 56 +#define CLK_BUS_UART4 57 + +#define CLK_NAND 59 +#define CLK_MMC0 60 +#define CLK_MMC0_SAMPLE 61 +#define CLK_MMC0_OUTPUT 62 +#define CLK_MMC1 63 +#define CLK_MMC1_SAMPLE 64 +#define CLK_MMC1_OUTPUT 65 +#define CLK_MMC2 66 +#define CLK_MMC2_SAMPLE 67 +#define CLK_MMC2_OUTPUT 68 +#define CLK_SS 69 +#define CLK_SPI0 70 +#define CLK_SPI1 71 +#define CLK_I2S0 72 +#define CLK_I2S1 73 +#define CLK_I2S2 74 +#define CLK_TDM 75 +#define CLK_SPDIF 76 +#define CLK_USB_PHY0 77 +#define CLK_USB_PHY1 78 +#define CLK_USB_HSIC 79 +#define CLK_USB_HSIC_12M 80 +#define CLK_USB_OHCI0 81 + +#define CLK_DRAM_VE 83 +#define CLK_DRAM_CSI 84 + +#define CLK_TCON0 85 +#define CLK_TCON1 86 +#define CLK_CSI_MISC 87 +#define CLK_MIPI_CSI 88 +#define CLK_CSI_MCLK 89 +#define CLK_CSI_SCLK 90 +#define CLK_VE 91 +#define CLK_AVS 92 +#define CLK_HDMI 93 +#define CLK_HDMI_SLOW 94 + +#define CLK_MIPI_DSI0 96 +#define CLK_MIPI_DSI1 97 +#define CLK_GPU_CORE 98 +#define CLK_GPU_MEMORY 99 +#define CLK_GPU_HYD 100 + +#endif /* _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_ */ diff --git a/include/dt-bindings/reset/sun8i-a83t-ccu.h b/include/dt-bindings/reset/sun8i-a83t-ccu.h new file mode 100644 index 0000000000..784f6e1166 --- /dev/null +++ b/include/dt-bindings/reset/sun8i-a83t-ccu.h @@ -0,0 +1,98 @@ +/* + * Copyright (C) 2017 Chen-Yu Tsai wens@csie.org + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_ +#define _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_ + +#define RST_USB_PHY0 0 +#define RST_USB_PHY1 1 +#define RST_USB_HSIC 2 + +#define RST_DRAM 3 +#define RST_MBUS 4 + +#define RST_BUS_MIPI_DSI 5 +#define RST_BUS_SS 6 +#define RST_BUS_DMA 7 +#define RST_BUS_MMC0 8 +#define RST_BUS_MMC1 9 +#define RST_BUS_MMC2 10 +#define RST_BUS_NAND 11 +#define RST_BUS_DRAM 12 +#define RST_BUS_EMAC 13 +#define RST_BUS_HSTIMER 14 +#define RST_BUS_SPI0 15 +#define RST_BUS_SPI1 16 +#define RST_BUS_OTG 17 +#define RST_BUS_EHCI0 18 +#define RST_BUS_EHCI1 19 +#define RST_BUS_OHCI0 20 + +#define RST_BUS_VE 21 +#define RST_BUS_TCON0 22 +#define RST_BUS_TCON1 23 +#define RST_BUS_CSI 24 +#define RST_BUS_HDMI0 25 +#define RST_BUS_HDMI1 26 +#define RST_BUS_DE 27 +#define RST_BUS_GPU 28 +#define RST_BUS_MSGBOX 29 +#define RST_BUS_SPINLOCK 30 + +#define RST_BUS_LVDS 31 + +#define RST_BUS_SPDIF 32 +#define RST_BUS_I2S0 33 +#define RST_BUS_I2S1 34 +#define RST_BUS_I2S2 35 +#define RST_BUS_TDM 36 + +#define RST_BUS_I2C0 37 +#define RST_BUS_I2C1 38 +#define RST_BUS_I2C2 39 +#define RST_BUS_UART0 40 +#define RST_BUS_UART1 41 +#define RST_BUS_UART2 42 +#define RST_BUS_UART3 43 +#define RST_BUS_UART4 44 + +#endif /* _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_ */