[U-Boot] [PATCH v3] Gbe Controller driver support for kirkwood SOCs

Contributors: Yotam Admon yotam@marvell.com Michael Blostein <michaelbl@marvell.com

Reviewed by: Ronen Shitrit rshitrit@marvell.com Signed-off-by: Prafulla Wadaskar prafulla@marvell.com --- Change log: v2: entire rewrite/restructure of v1 used small names for variable/function names readl/writel used to access SoC registers Soc registers accssed using pointers through net device struct miiphy registration done for external smi read/write access miiphy_link used to detect phy link presence cleaned for cosmetic changes

v3: asm/arch/kirkwood.h included in c file

cpu/arm926ejs/kirkwood/cpu.c | 8 + drivers/net/Makefile | 1 + drivers/net/kirkwood_egiga.c | 1669 ++++++++++++++++++++++++++++++++++++++++++ drivers/net/kirkwood_egiga.h | 828 +++++++++++++++++++++ include/netdev.h | 1 + 5 files changed, 2507 insertions(+), 0 deletions(-) create mode 100644 drivers/net/kirkwood_egiga.c create mode 100644 drivers/net/kirkwood_egiga.h

diff --git a/cpu/arm926ejs/kirkwood/cpu.c b/cpu/arm926ejs/kirkwood/cpu.c index c1e9146..b440008 100644 --- a/cpu/arm926ejs/kirkwood/cpu.c +++ b/cpu/arm926ejs/kirkwood/cpu.c @@ -295,3 +295,11 @@ int arch_misc_init(void) return 0; } #endif /* CONFIG_ARCH_MISC_INIT */ + +#ifdef CONFIG_KIRKWOOD_EGIGA +int cpu_eth_init(bd_t *bis) +{ + kirkwood_egiga_initialize(bis); + return 0; +} +#endif diff --git a/drivers/net/Makefile b/drivers/net/Makefile index a360a50..f0c5654 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -40,6 +40,7 @@ COBJS-$(CONFIG_ENC28J60) += enc28j60.o COBJS-$(CONFIG_FSLDMAFEC) += fsl_mcdmafec.o mcfmii.o COBJS-$(CONFIG_GRETH) += greth.o COBJS-$(CONFIG_INCA_IP_SWITCH) += inca-ip_sw.o +COBJS-$(CONFIG_KIRKWOOD_EGIGA) += kirkwood_egiga.o COBJS-$(CONFIG_DRIVER_KS8695ETH) += ks8695eth.o COBJS-$(CONFIG_DRIVER_LAN91C96) += lan91c96.o COBJS-$(CONFIG_MACB) += macb.o diff --git a/drivers/net/kirkwood_egiga.c b/drivers/net/kirkwood_egiga.c new file mode 100644 index 0000000..d9b295a --- /dev/null +++ b/drivers/net/kirkwood_egiga.c @@ -0,0 +1,1669 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar prafulla@marvell.com + * + * (C) Copyright 2003 + * Ingo Assmus ingo.assmus@keymile.com + * + * based on - Driver for MV64360X ethernet ports + * Copyright (C) 2002 rabeeh@galileo.co.il + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <net.h> +#include <malloc.h> +#include <miiphy.h> +#include <asm/errno.h> +#include <asm/types.h> +#include <asm/byteorder.h> + +/* In case SRAM is cache coherent or non-cacheable */ +#define CONFIG_NOT_COHERENT_CACHE +#define D_CACHE_FLUSH_LINE(addr, offset) ; +#define CPU_PIPE_FLUSH { __asm__ __volatile__ ("nop;nop;nop;nop;nop;nop;nop");} + +#include "kirkwood_egiga.h" + +/* + * smi_reg_read - Read from ethernet phy register. + * + * INPUT: + * @phy_adr - Phy address. + * @reg_ofs - Phy register offset. + * + * This function reads ethernet phy register. + * REturns 16bit phy register value, or 0xffff on error + */ +int smi_reg_read(char *devname, u8 phy_adr, u8 reg_ofs, u16 * data) +{ + struct eth_device *dev = eth_get_dev_by_name(devname); + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct kwgbe_registers *regs = dkwgbe->regs; + u32 smi_reg; + volatile u32 timeout; + + /* check to read parameters */ + if (phy_adr == 0xEE && reg_ofs == 0xEE) { + data = (void *)(0x00ff & KWGBEREG_RD(regs->phyadr)); + return 0; + } + /* check parameters */ + if ((phy_adr << KWGBE_PHY_SMI_DEV_ADDR_OFFS) & + ~KWGBE_PHY_SMI_DEV_ADDR_MASK) { + printf("Illegal PHY device address %d\n", phy_adr); + return -EFAULT; + } + if ((reg_ofs << KWGBE_SMI_REG_ADDR_OFFS) & ~KWGBE_SMI_REG_ADDR_MASK) { + printf("Illegal PHY register offset %d\n", reg_ofs); + return -EFAULT; + } + + timeout = KWGBE_PHY_SMI_TIMEOUT; + /* wait till the SMI is not busy */ + do { + /* read smi register */ + smi_reg = KWGBEREG_RD(regs->smi); + if (timeout-- == 0) { + printf("SMI busy timeout\n"); + return -EFAULT; + } + } while (smi_reg & KWGBE_PHY_SMI_BUSY_MASK); + + /* fill the phy address and regiser offset and read opcode */ + smi_reg = + (phy_adr << KWGBE_PHY_SMI_DEV_ADDR_OFFS) | (reg_ofs << + KWGBE_SMI_REG_ADDR_OFFS) + | KWGBE_PHY_SMI_OPCODE_READ; + + /* write the smi register */ + KWGBEREG_WR(regs->smi, smi_reg); + + /*wait till readed value is ready */ + timeout = KWGBE_PHY_SMI_TIMEOUT; + do { + /* read smi register */ + smi_reg = KWGBEREG_RD(regs->smi); + if (timeout-- == 0) { + printf("SMI read-valid timeout\n"); + return -EFAULT; + } + } while (!(smi_reg & KWGBE_PHY_SMI_READ_VALID_MASK)); + + /* Wait for the data to update in the SMI register */ + for (timeout = 0; timeout < KWGBE_PHY_SMI_TIMEOUT; timeout++) ; + + *data = (u16) (KWGBEREG_RD(regs->smi) & KWGBE_PHY_SMI_DATA_MASK); + + debug("Reg(phyadr %d, off %d) Phy-value = %04x\n", phy_adr, + reg_ofs, *data); + + return 0; +} + +/* + * smi_reg_write - Write to ethernet phy register. + * + * @phy_adr - Phy address. + * @reg_ofs - Phy register offset. + * @data - 16bit data. + * + * This function write to ethernet phy register. + * Returns 0 if write succeed, -EINVAL on bad parameters , MV_ERROR on error . + * -ETIME on timeout + */ +int smi_reg_write(char *devname, u8 phy_adr, u8 reg_ofs, u16 data) +{ + struct eth_device *dev = eth_get_dev_by_name(devname); + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct kwgbe_registers *regs = dkwgbe->regs; + u32 smi_reg; + volatile u32 timeout; + + /* check parameters */ + if ((phy_adr << KWGBE_PHY_SMI_DEV_ADDR_OFFS) & + ~KWGBE_PHY_SMI_DEV_ADDR_MASK) { + printf("Illegal phy address\n"); + return -EINVAL; + } + if ((reg_ofs << KWGBE_SMI_REG_ADDR_OFFS) & ~KWGBE_SMI_REG_ADDR_MASK) { + printf("Illegal register offset\n"); + return -EINVAL; + } + + /* wait till the SMI is not busy */ + timeout = KWGBE_PHY_SMI_TIMEOUT; + do { + /* read smi register */ + smi_reg = KWGBEREG_RD(regs->smi); + if (timeout-- == 0) { + printf("SMI busy timeout\n"); + return -ETIME; + } + } while (smi_reg & KWGBE_PHY_SMI_BUSY_MASK); + + /* fill the phy address and regiser offset and write opcode and data */ + smi_reg = (data << KWGBE_PHY_SMI_DATA_OFFS); + smi_reg |= + (phy_adr << KWGBE_PHY_SMI_DEV_ADDR_OFFS) | (reg_ofs << + KWGBE_SMI_REG_ADDR_OFFS); + smi_reg &= ~KWGBE_PHY_SMI_OPCODE_READ; + + /* write the smi register */ + KWGBEREG_WR(regs->smi, smi_reg); + + return 0; +} + +static int egiga_free_tx_rings(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct kwgbe_portinfo *portinfo = &dkwgbe->portinfo; + struct kwgbe_registers *regs = dkwgbe->regs; + + u32 queue; + volatile struct kwgbe_tx_dscr *p_tx_curr_desc; + + /* Stop Tx Queues */ + KWGBEREG_WR(regs->tqc, 0x0000ff00); + + /* Free TX rings */ + debug("Clearing previously allocated TX queues... \n"); + for (queue = 0; queue < KW_TXQ_NO; queue++) { + /* Free on TX rings */ + for (p_tx_curr_desc = portinfo->p_tx_desc_area_base[queue]; + ((u32) p_tx_curr_desc <= + (u32) portinfo->p_tx_desc_area_base[queue] + + portinfo->tx_desc_area_size[queue]); + p_tx_curr_desc = + (struct kwgbe_tx_dscr *)((u32) p_tx_curr_desc + + TX_DESC_ALIGNED_SIZE)) { + /* this is inside for loop */ + if (p_tx_curr_desc->retinfo != 0) { + p_tx_curr_desc->retinfo = 0; + debug("freed\n"); + } + } + debug("Done\n"); + } + return 0; +} + +static int egiga_free_rx_rings(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct kwgbe_portinfo *portinfo = &dkwgbe->portinfo; + struct kwgbe_registers *regs = dkwgbe->regs; + + u32 queue; + volatile struct kwgbe_rx_dscr *p_rx_curr_desc; + + /* Stop RX Queues */ + KWGBEREG_WR(regs->rqc, 0x0000ff00); + + /* Free RX rings */ + debug("Clearing previously allocated RX queues...\n"); + for (queue = 0; queue < KW_RXQ_NO; queue++) { + /* Free preallocated skb's on RX rings */ + for (p_rx_curr_desc = portinfo->p_rx_desc_area_base[queue]; + (((u32) p_rx_curr_desc < + ((u32) portinfo->p_rx_desc_area_base[queue] + + portinfo->rx_desc_area_size[queue]))); + p_rx_curr_desc = + (struct kwgbe_rx_dscr *)((u32) p_rx_curr_desc + + RX_DESC_ALIGNED_SIZE)) { + if (p_rx_curr_desc->retinfo != 0) { + p_rx_curr_desc->retinfo = 0; + debug("freed\n"); + } + } + debug("Done\n"); + } + return 0; +} + +static void phy_set_addr(struct kwgbe_registers *regs, int phy_addr) +{ + KWGBEREG_WR(regs->phyadr, phy_addr); +} + +#ifdef UPDATE_STATS_BY_SOFTWARE +/* + * egiga_print_stat + * + * Update the statistics structure in the private data structure + * + * Input : pointer to ethernet interface network device structure + * Output : N/A + */ +static void egiga_print_stat(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct egiga_priv *portpriv = &dkwgbe->portpriv; + struct net_device_stats *stats = &portpriv->stats; + + /* These are false updates */ + printf("\n### Network statistics: ###\n"); + printf("--------------------------\n"); + printf(" Packets received: %d\n", stats->rx_packets); + printf(" Packets send: %d\n", stats->tx_packets); + printf(" Received bytes: %lld\n", stats->rx_bytes); + printf(" Send bytes: %lld\n", stats->tx_bytes); + if (stats->rx_errors != 0) + printf(" Rx Errors: %d\n", + stats->rx_errors); + if (stats->rx_dropped != 0) + printf(" Rx dropped (CRC Errors): %d\n", + stats->rx_dropped); + if (stats->multicast != 0) + printf(" Rx mulicast frames: %d\n", + stats->multicast); + if (stats->collisions != 0) + printf(" No. of collisions: %d\n", + stats->collisions); + if (stats->rx_length_errors != 0) + printf(" Rx length errors: %d\n", + stats->rx_length_errors); +} +#endif + +/* + * kwgbe_stop + * + * This function is used when closing the network device. + * It updates the hardware, + * release all memory that holds buffers and descriptors and release the IRQ. + * Input : a pointer to the device structure + * Output : zero if success , nonzero if fails + */ +int kwgbe_stop(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct kwgbe_registers *regs = dkwgbe->regs; + + /* Disable all gigE address decoder */ + KWGBEREG_WR(regs->bare, 0x3f); + + egiga_free_tx_rings(dev); + egiga_free_rx_rings(dev); + + port_reset(regs); + /* Disable ethernet port interrupts */ + KWGBEREG_WR(regs->ic, 0); + KWGBEREG_WR(regs->ice, 0); + /* Mask RX buffer and TX end interrupt */ + KWGBEREG_WR(regs->pim, 0); + /* Mask phy and link status changes interrupts */ + KWGBEREG_WR(regs->peim, 0); + + /* Print Network statistics */ +#ifdef UPDATE_STATS_BY_SOFTWARE + /* + * Print statistics (only if ethernet is running), + * then zero all the stats fields in memory + */ + if (portpriv->running == MAGIC_KWGBE_RUNNING) { + portpriv->running = 0; + egiga_print_stat(dev); + } + memset(&portpriv->stats, 0, sizeof(struct net_device_stats)); +#endif + debug("Ethernet stopped ...\n"); + return 0; +} + +/* + * clear_mib_counters - Clear all MIB counters + * + * This function clears all MIB counters of a specific ethernet port. + * A read from the MIB counter will reset the counter. + * + * OUTPUT: After reading all MIB counters, the counters resets. + * RETURN: MIB counter value. + */ +static void clear_mib_counters(u32 mibc) +{ + u32 i = mibc + 0x80; + u32 dummy; + + /* Perform dummy reads from MIB counters */ + for (; mibc < i; mibc += 4) { + dummy = readl(mibc); + } +} + +/* + * egiga_update_stat + * + * Update the statistics structure in the private data structure + * + * Input : pointer to ethernet interface network device structure + * Output : N/A + */ +static void egiga_update_stat(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct egiga_priv *portpriv = &dkwgbe->portpriv; + struct net_device_stats *stats = &portpriv->stats; + struct mib_counters *mibc = &dkwgbe->regs->mibc; + + /* These are false updates */ + stats->rx_packets += KWGBEREG_RD(mibc->good_frames_received); + stats->tx_packets += KWGBEREG_RD(mibc->good_frames_sent); + stats->rx_bytes += KWGBEREG_RD(mibc->good_octets_received); + stats->tx_bytes += KWGBEREG_RD(mibc->good_octets_sent); + stats->rx_errors += KWGBEREG_RD(mibc->mac_receive_error); + /* Rx dropped is for received packet with CRC error */ + stats->rx_dropped += KWGBEREG_RD(mibc->bad_crc_event); + stats->multicast += KWGBEREG_RD(mibc->multicast_frames_received); + stats->collisions += + KWGBEREG_RD(mibc->collision) + KWGBEREG_RD(mibc->late_collision); + stats->rx_length_errors += + KWGBEREG_RD(mibc->undersize_received) + + KWGBEREG_RD(mibc->oversize_received); +} + +/* + * egiga_get_stats + * + * Returns a pointer to the interface statistics. + * + * Input : dev - a pointer to the required interface + * Output : a pointer to the interface's statistics + */ +static struct net_device_stats *egiga_get_stats(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct egiga_priv *portpriv = &dkwgbe->portpriv; + + egiga_update_stat(dev); + return &portpriv->stats; +} + +/* + * set_access_control - Config address decode parameters for Ethernet unit + * + * This function configures the address decode parameters for the Gigabit + * Ethernet Controller according the given parameters struct. + * + * @regs Register struct pointer. + * @param Address decode parameter struct. + */ +static void set_access_control(struct kwgbe_registers *regs, + struct kwgbe_winparam *param) +{ + u32 access_prot_reg; + + /* Set access control register */ + access_prot_reg = KWGBEREG_RD(regs->epap); + access_prot_reg &= (~(3 << (param->win * 2))); /* clear window permission */ + access_prot_reg |= (param->access_ctrl << (param->win * 2)); + KWGBEREG_WR(regs->epap, access_prot_reg); + + /* Set window Size reg (SR) */ + KWGBEREG_WR(regs->barsz[param->win].size, + (((param->size / 0x10000) - 1) << 16)); + + /* Set window Base address reg (BA) */ + KWGBEREG_WR(regs->barsz[param->win].bar, + (param->target | param->attrib | param->base_addr)); + /* High address remap reg (HARR) */ + if (param->win < 4) + KWGBEREG_WR(regs->ha_remap[param->win], param->high_addr); + + /* Base address enable reg (BARER) */ + if (param->enable == 1) + KWGBEREG_BITS_RESET(regs->bare, (1 << param->win)); + else + KWGBEREG_BITS_SET(regs->bare, (1 << param->win)); +} + +static void set_dram_access(struct kwgbe_registers *regs) +{ + struct kwgbe_winparam win_param; + int i; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + /* Set access parameters for DRAM bank i */ + win_param.win = i; /* Use Ethernet window i */ + win_param.target = KWGBE_TARGET_DRAM; /* Window target - DDR */ + win_param.access_ctrl = EWIN_ACCESS_FULL; /* Enable full access */ + win_param.high_addr = 0; + /* Get bank base */ + win_param.base_addr = kw_sdram_bar(i); + win_param.size = kw_sdram_bs(i); /* Get bank size */ + if (win_param.size == 0) + win_param.enable = 0; + else + win_param.enable = 1; /* Enable the access */ + switch (i) { + case 0: + /* Enable DRAM bank 0 */ + win_param.attrib = EBAR_ATTR_DRAM_CS0; + break; + case 1: + /* Enable DRAM bank 1 */ + win_param.attrib = EBAR_ATTR_DRAM_CS1; + break; + case 2: + /* Enable DRAM bank 2 */ + win_param.attrib = EBAR_ATTR_DRAM_CS2; + break; + case 3: + /* Enable DRAM bank 3 */ + win_param.attrib = EBAR_ATTR_DRAM_CS3; + break; + default: + /* invalide bank, disable access */ + win_param.enable = 0; + win_param.attrib = 0; + break; + } +#ifndef CONFIG_NOT_COHERENT_CACHE + win_param.attrib |= EBAR_ATTR_DRAM_CACHE_COHERENCY_WB; +#endif + /* Set the access control for address window (EPAPR) READ & WRITE */ + set_access_control(regs, &win_param); + } +} + +/* + * port_init_mac_tables - Clear all entrance in the UC, SMC and OMC tables + * + * Go through all the DA filter tables (Unicast, Special Multicast & Other + * Multicast) and set each entry to 0. + * + */ +static void port_init_mac_tables(struct kwgbe_registers *regs) +{ + int table_index; + + /* Clear DA filter unicast table (Ex_dFUT) */ + for (table_index = 0; table_index < 4; ++table_index) + KWGBEREG_WR(regs->dfut[table_index], 0); + + for (table_index = 0; table_index < 64; ++table_index) { + /* Clear DA filter special multicast table (Ex_dFSMT) */ + KWGBEREG_WR(regs->dfsmt[table_index], 0); + /* Clear DA filter other multicast table (Ex_dFOMT) */ + KWGBEREG_WR(regs->dfomt[table_index], 0); + } +} + +/* + * port_init - Initialize the Ethernet port driver + * + * @p_gbe_pctrl - ptr to Ethernet port control struct + * + * This function prepares the ethernet port to start its activity: + * 1) Completes the ethernet port driver struct initialization toward port + * start routine. + * 2) Resets the device to a quiescent state in case of warm reboot. + * 3) Enable SDMA access to all four DRAM banks as well as internal SRAM. + * 4) Clean MAC tables. The reset status of those tables is unknown. + * 5) Set PHY address. + * Note: Call this routine prior to port_start routine and after setting + * user values in the user fields of Ethernet port control struct (i.e. + * port_phy_addr). + * + */ +static void port_init(struct kwgbe_device *dkwgbe) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + struct kwgbe_registers *regs = dkwgbe->regs; + int queue; + + p_gbe_pctrl->port_config = PRT_CFG_VAL; + p_gbe_pctrl->port_config_extend = PORT_CFG_EXTEND_VALUE; + p_gbe_pctrl->port_sdma_config = PORT_SDMA_CFG_VALUE; + p_gbe_pctrl->port_serial_control = PORT_SERIAL_CONTROL_VALUE; + + p_gbe_pctrl->port_rx_queue_command = 0; + p_gbe_pctrl->port_tx_queue_command = 0; + + /* Stop RX Queues */ + KWGBEREG_WR(regs->rqc, 0x0000ff00); + + /* Clear the ethernet port interrupts */ + KWGBEREG_WR(regs->ic, 0); + KWGBEREG_WR(regs->ice, 0); + + /* Unmask RX buffer and TX end interrupt */ + KWGBEREG_WR(regs->pim, INT_CAUSE_UNMASK_ALL); + + /* Unmask phy and link status changes interrupts */ + KWGBEREG_WR(regs->peim, INT_CAUSE_UNMASK_ALL_EXT); + + /* Zero out SW structs */ + for (queue = 0; queue < MAX_RXQ_NO; queue++) { + CURR_RFD_SET((struct kwgbe_rx_dscr *)0x00000000, queue); + USED_RFD_SET((struct kwgbe_rx_dscr *)0x00000000, queue); + p_gbe_pctrl->rx_resource_err[queue] = 0; + } + + for (queue = 0; queue < MAX_TXQ_NO; queue++) { + CURR_TFD_SET((struct kwgbe_tx_dscr *)0x00000000, queue); + USED_TFD_SET((struct kwgbe_tx_dscr *)0x00000000, queue); + FIRST_TFD_SET((struct kwgbe_tx_dscr *)0x00000000, queue); + p_gbe_pctrl->tx_resource_err[queue] = 0; + } + + port_reset(regs); + set_dram_access(regs); + port_init_mac_tables(regs); +} + +/* + * port_start - Start the Ethernet port activity. + * + * This routine prepares the Ethernet port for Rx and Tx activity: + * 1. Initialize Tx and Rx Current Descriptor Pointer for each queue that + * has been initialized a descriptor's ring (using kwgbe_init_tx_desc_ring + * for Tx and kwgbe_init_rx_desc_ring for Rx) + * 2. Initialize and enable the Ethernet configuration port by writing to + * the port's configuration and command registers. + * 3. Initialize and enable the SDMA by writing to the SDMA's + * configuration and command registers. + * After completing these steps, the ethernet port SDMA can starts to + * perform Rx and Tx activities. + * + * Note: Each Rx and Tx queue descriptor's list must be initialized prior + * to calling this function (use kwgbe_init_tx_desc_ring for Tx queues and + * kwgbe_init_rx_desc_ring for Rx queues). + * + * OUTPUT: Ethernet port is ready to receive and transmit. + * + * RETURN: 0 if the port PHY is not up. 1 otherwise. + */ +static void port_start(struct kwgbe_device *dkwgbe) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + struct kwgbe_registers *regs = dkwgbe->regs; + int queue; + volatile struct kwgbe_tx_dscr *p_tx_curr_desc; + volatile struct kwgbe_rx_dscr *p_rx_curr_desc; + + /* Assignment of Tx CTRP of given queue */ + for (queue = 0; queue < MAX_TXQ_NO; queue++) { + CURR_TFD_GET(p_tx_curr_desc, queue); + KWGBEREG_WR(regs->tcqdp[queue], (u32) p_tx_curr_desc); + } + + /* Assignment of Rx CRDB of given queue */ + for (queue = 0; queue < MAX_RXQ_NO; queue++) { + CURR_RFD_GET(p_rx_curr_desc, queue); + KWGBEREG_WR(regs->crdp[queue], (u32) p_rx_curr_desc); + + if (p_rx_curr_desc != NULL) + /* Add the assigned Ethernet address to the port's address table */ + port_uc_addr_set(regs, p_gbe_pctrl->port_mac_addr, + queue); + } + + /* Assign port configuration and command. */ + KWGBEREG_WR(regs->pxc, p_gbe_pctrl->port_config); + KWGBEREG_WR(regs->pxcx, p_gbe_pctrl->port_config_extend); + KWGBEREG_WR(regs->psc0, p_gbe_pctrl->port_serial_control); + KWGBEREG_BITS_SET(regs->psc0, KWGBE_SERIAL_PORT_EN); + + /* Assign port SDMA configuration */ + KWGBEREG_WR(regs->sdc, p_gbe_pctrl->port_sdma_config); + KWGBEREG_WR(regs->tqx[0].qxttbc, 0x3fffffff); + KWGBEREG_WR(regs->tqx[0].tqxtbc, 0x03fffcff); + /* Turn off the port/queue bandwidth limitation */ + KWGBEREG_WR(regs->pmtu, 0x0); + + /* Enable port Rx. */ + KWGBEREG_WR(regs->rqc, p_gbe_pctrl->port_rx_queue_command); + + /* Set maximum receive buffer to 9700 bytes */ + KWGBEREG_WR(regs->psc0, + (0x5 << 17) | (KWGBEREG_RD(regs->psc0) & 0xfff1ffff)); + + /* + * Set ethernet MTU for leaky bucket mechanism to 0 - this will + * disable the leaky bucket mechanism . + */ + KWGBEREG_WR(regs->pmtu, 0); +} + +/* + * port_uc_addr - This function Set the port unicast address table + * + * This function locates the proper entry in the Unicast table for the + * specified MAC nibble and sets its properties according to function + * parameters. + * This function add/removes MAC addresses from the port unicast address + * table. + * + * @uc_nibble Unicast MAC Address last nibble. + * @queue Rx queue number for this MAC address. + * @option 0 = Add, 1 = remove address. + * + * RETURN: 1 if output succeeded. 0 if option parameter is invalid. + */ +static int port_uc_addr(struct kwgbe_registers *regs, u8 uc_nibble, + enum kwgbe_q queue, int option) +{ + u32 unicast_reg; + u32 tbl_offset; + u32 reg_offset; + + /* Locate the Unicast table entry */ + uc_nibble = (0xf & uc_nibble); + tbl_offset = (uc_nibble / 4); /* Register offset from unicast table base */ + reg_offset = uc_nibble % 4; /* Entry offset within the above register */ + + switch (option) { + case REJECT_MAC_ADDR: + /* Clear accepts frame bit at specified unicast DA table entry */ + unicast_reg = KWGBEREG_RD(regs->dfut[tbl_offset]); + unicast_reg &= (0xFF << (8 * reg_offset)); + KWGBEREG_WR(regs->dfut[tbl_offset], unicast_reg); + break; + case ACCEPT_MAC_ADDR: + /* Set accepts frame bit at unicast DA filter table entry */ + unicast_reg = KWGBEREG_RD(regs->dfut[tbl_offset]); + unicast_reg &= (0xFF << (8 * reg_offset)); + unicast_reg |= ((0x01 | (queue << 1)) << (8 * reg_offset)); + KWGBEREG_WR(regs->dfut[tbl_offset], unicast_reg); + break; + default: + return 0; + } + return 1; +} + +/* + * port_uc_addr_set - This function Set the port Unicast address. + * + * This function Set the port Ethernet MAC address. + * + * @p_addr Address to be set + * @queue Rx queue number for this MAC address. + * + * OUTPUT: Set MAC address low and high registers. also calls + * port_uc_addr() To set the unicast table with the proper info. + */ +static void port_uc_addr_set(struct kwgbe_registers *regs, u8 * p_addr, + enum kwgbe_q queue) +{ + u32 mac_h; + u32 mac_l; + + mac_l = (p_addr[4] << 8) | (p_addr[5]); + mac_h = + (p_addr[0] << 24) | (p_addr[1] << 16) | (p_addr[2] << 8) | + (p_addr[3] << 0); + + KWGBEREG_WR(regs->macal, mac_l); + KWGBEREG_WR(regs->macah, mac_h); + + /* Accept frames of this address */ + port_uc_addr(regs, p_addr[5], queue, ACCEPT_MAC_ADDR); +} + +/* + * port_reset - Reset Ethernet port + * + * This routine resets the chip by aborting any SDMA engine activity and + * clearing the MIB counters. The Receiver and the Transmit unit are in + * idle state after this command is performed and the port is disabled. + * + */ +static void port_reset(struct kwgbe_registers *regs) +{ + u32 reg_data, i; + + /* Stop Tx port activity. Check port Tx activity. */ + reg_data = KWGBEREG_RD(regs->tqc); + + if (reg_data & 0xFF) { + /* Issue stop command for active channels only */ + KWGBEREG_WR(regs->tqc, (reg_data << 8)); + + /* Wait for all Tx activity to terminate. */ + do { + /* Check port cause register that all Tx queues are stopped */ + reg_data = KWGBEREG_RD(regs->tqc); + } + while (reg_data & 0xFF); + } + + /* Stop Rx port activity. Check port Rx activity. */ + reg_data = KWGBEREG_RD(regs->rqc); + + if (reg_data & 0xFF) { + /* Issue stop command for active channels only */ + KWGBEREG_WR(regs->rqc, (reg_data << 8)); + + /* Wait for all Rx activity to terminate. */ + do { + /* Check port cause register that all Rx queues are stopped */ + reg_data = KWGBEREG_RD(regs->rqc); + } + while (reg_data & 0xFF); + } + + /* Clear all MIB counters */ + clear_mib_counters((u32) & regs->mibc); + + /* Enable port in the Configuration Register */ + KWGBEREG_BITS_RESET(regs->psc0, KWGBE_SERIAL_PORT_EN); + /* Set port of active in the Configuration Register */ + KWGBEREG_BITS_RESET(regs->psc1, 1 << 4); +#ifdef CONFIG_SYS_MII_MODE + /* Set MMI interface up */ + KWGBEREG_BITS_RESET(regs->psc1, 1 << 3); +#endif + for (i = 0; i < 4000; i++) ; + return; +} + +/* + * kwgbe_init_rx_desc_ring - Curve a Rx chain desc list and buffer in memory. + * + * This function prepares a Rx chained list of descriptors and packet + * buffers in a form of a ring. The routine must be called after port + * initialization routine and before port start routine. + * The Ethernet SDMA engine uses CPU bus addresses to access the various + * devices in the system (i.e. DRAM). This function uses the ethernet + * struct 'virtual to physical' routine (set by the user) to set the ring + * with physical addresses. + * + * @rx_queue Number of Rx queue. + * @rx_desc_num Number of Rx descriptors + * @rx_buff_size Size of Rx buffer + * @rx_desc_base_addr Rx descriptors memory area base addr. + * @rx_buff_base_addr Rx buffer memory area base addr. + * + * The routine updates the Ethernet port control struct with information + * regarding the Rx descriptors and buffers. + * + * RETURN: + * 0 if the given descriptors memory area is not aligned according to + * Ethernet SDMA specifications. + * 1 otherwise. + */ +static int kwgbe_init_rx_desc_ring(struct kwgbe_device *dkwgbe, + enum kwgbe_q rx_queue, + int rx_desc_num, + int rx_buff_size, + u32 rx_desc_base_addr, u32 rx_buff_base_addr) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + struct kwgbe_rx_dscr *p_rx_desc; + /* pointer to link with the last descriptor */ + struct kwgbe_rx_dscr *p_rx_prev_desc; + u32 buffer_addr; + int ix; /* a counter */ + + p_rx_desc = (struct kwgbe_rx_dscr *)rx_desc_base_addr; + p_rx_prev_desc = p_rx_desc; + buffer_addr = rx_buff_base_addr; + + /* Rx desc Must be 4LW aligned (i.e. Descriptor_Address[3:0]=0000). */ + if (rx_buff_base_addr & 0xF) + return 0; + + /* Rx buffers are limited to 64K bytes and Minimum size is 8 bytes */ + if ((rx_buff_size < 8) || (rx_buff_size > RX_BUF_MXSZ)) + return 0; + + /* Rx buffers must be 64-bit aligned. */ + if ((rx_buff_base_addr + rx_buff_size) & 0x7) + return 0; + + /* initialize the Rx descriptors ring */ + for (ix = 0; ix < rx_desc_num; ix++) { + p_rx_desc->buf_size = rx_buff_size; + p_rx_desc->byte_cnt = 0x0000; + p_rx_desc->cmd_sts = + KWGBE_BUFFER_OWNED_BY_DMA | KWGBE_RX_EN_INTERRUPT; + p_rx_desc->nxtdesc_p = ((u32) p_rx_desc) + RX_DESC_ALIGNED_SIZE; + p_rx_desc->buf_ptr = buffer_addr; + p_rx_desc->retinfo = 0x00000000; + D_CACHE_FLUSH_LINE(p_rx_desc, 0); + buffer_addr += rx_buff_size; + p_rx_prev_desc = p_rx_desc; + p_rx_desc = (struct kwgbe_rx_dscr *) + ((u32) p_rx_desc + RX_DESC_ALIGNED_SIZE); + } + + /* Closing Rx descriptors ring */ + p_rx_prev_desc->nxtdesc_p = (rx_desc_base_addr); + D_CACHE_FLUSH_LINE(p_rx_prev_desc, 0); + + /* Save Rx desc pointer to driver struct. */ + CURR_RFD_SET((struct kwgbe_rx_dscr *)rx_desc_base_addr, rx_queue); + USED_RFD_SET((struct kwgbe_rx_dscr *)rx_desc_base_addr, rx_queue); + + p_gbe_pctrl->p_rx_desc_area_base[rx_queue] = + (struct kwgbe_rx_dscr *)rx_desc_base_addr; + p_gbe_pctrl->rx_desc_area_size[rx_queue] = + rx_desc_num * RX_DESC_ALIGNED_SIZE; + + p_gbe_pctrl->port_rx_queue_command |= (1 << rx_queue); + + return 1; +} + +/* + * kwgbe_init_tx_desc_ring - Curve a Tx chain desc list and buffer in memory. + * + * This function prepares a Tx chained list of descriptors and packet + * buffers in a form of a ring. The routine must be called after port + * initialization routine and before port start routine. + * The Ethernet SDMA engine uses CPU bus addresses to access the various + * devices in the system (i.e. DRAM). This function uses the ethernet + * struct 'virtual to physical' routine (set by the user) to set the ring + * with physical addresses. + * + * @p_gbe_pctrl Ethernet Port Control srtuct ptr. + * @tx_queue Number of Tx queue. + * @tx_desc_num Number of Tx descriptors + * @tx_buff_size Size of Tx buffer + * @tx_desc_base_addr Tx descriptors memory area base addr. + * @tx_buff_base_addr Tx buffer memory area base addr. + * + * The routine updates the Ethernet port control struct with information + * regarding the Tx descriptors and buffers. + * + * RETURN: + * 0 if the given descriptors memory area is not aligned according to + * Ethernet SDMA specifications. + * 1 otherwise. + */ +static int kwgbe_init_tx_desc_ring(struct kwgbe_device *dkwgbe, + enum kwgbe_q tx_queue, + int tx_desc_num, + int tx_buff_size, + u32 tx_desc_base_addr, u32 tx_buff_base_addr) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + struct kwgbe_tx_dscr *p_tx_desc; + struct kwgbe_tx_dscr *p_tx_prev_desc; + u32 buffer_addr; + int ix; /* a counter */ + + /* save the first desc pointer to link with the last descriptor */ + p_tx_desc = (struct kwgbe_tx_dscr *)tx_desc_base_addr; + p_tx_prev_desc = p_tx_desc; + buffer_addr = tx_buff_base_addr; + + /* Tx desc Must be 4LW aligned (i.e. Descriptor_Address[3:0]=0000). */ + if (tx_buff_base_addr & 0xF) + return 0; + + /* Tx buffers are limited to 64K bytes and Minimum size is 8 bytes */ + if ((tx_buff_size > TX_BUF_MXSZ) + || (tx_buff_size < TX_BUF_MNSZ)) + return 0; + + /* Initialize the Tx descriptors ring */ + for (ix = 0; ix < tx_desc_num; ix++) { + p_tx_desc->byte_cnt = 0x0000; + p_tx_desc->l4i_chk = 0x0000; + p_tx_desc->cmd_sts = 0x00000000; + p_tx_desc->nxtdesc_p = ((u32) p_tx_desc) + TX_DESC_ALIGNED_SIZE; + + p_tx_desc->buf_ptr = buffer_addr; + p_tx_desc->retinfo = 0x00000000; + D_CACHE_FLUSH_LINE(p_tx_desc, 0); + buffer_addr += tx_buff_size; + p_tx_prev_desc = p_tx_desc; + p_tx_desc = (struct kwgbe_tx_dscr *) + ((u32) p_tx_desc + TX_DESC_ALIGNED_SIZE); + + } + /* Closing Tx descriptors ring */ + p_tx_prev_desc->nxtdesc_p = tx_desc_base_addr; + D_CACHE_FLUSH_LINE(p_tx_prev_desc, 0); + /* Set Tx desc pointer in driver struct. */ + CURR_TFD_SET((struct kwgbe_tx_dscr *)tx_desc_base_addr, tx_queue); + USED_TFD_SET((struct kwgbe_tx_dscr *)tx_desc_base_addr, tx_queue); + + /* Init Tx ring base and size parameters */ + p_gbe_pctrl->p_tx_desc_area_base[tx_queue] = + (struct kwgbe_tx_dscr *)tx_desc_base_addr; + p_gbe_pctrl->tx_desc_area_size[tx_queue] = + (tx_desc_num * TX_DESC_ALIGNED_SIZE); + + /* Add the queue to the list of Tx queues of this port */ + p_gbe_pctrl->port_tx_queue_command |= (1 << tx_queue); + + return 1; +} + +/* + * b_copy - Copy bytes from source to destination + * + * This function supports the eight bytes limitation on Tx buffer size. + * The routine will zero eight bytes starting from the destination address + * followed by copying bytes from the source address to the destination. + * + * @src_addr 32 bit source address. + * @dst_add 32 bit destination address. + * @byte_count Number of bytes to copy. + */ +static void b_copy(u32 src_addr, u32 dst_addr, int byte_count) +{ + /* Zero the dst_addr area */ + *(u32 *) dst_addr = 0x0; + + while (byte_count != 0) { + *(char *)dst_addr = *(char *)src_addr; + dst_addr++; + src_addr++; + byte_count--; + } +} + +/* + * port_send - Send an Ethernet packet + * + * This routine send a given packet described by p_pktinfo parameter. It + * supports transmitting of a packet spaned over multiple buffers. The + * routine updates 'curr' and 'first' indexes according to the packet + * segment passed to the routine. In case the packet segment is first, + * the 'first' index is update. In any case, the 'curr' index is updated. + * If the routine get into Tx resource error it assigns 'curr' index as + * 'first'. This way the function can abort Tx process of multiple + * descriptors per packet. + * + * @tx_queue Number of Tx queue. + * @p_pkt_info User packet buffer ptr. + * + * OUTPUT: Tx ring 'curr' and 'first' indexes are updated. + * + * RETURN: + * KWGBE_QFULL in case of Tx resource error. + * KWGBE_ERROR in case the routine can not access Tx desc ring. + * KWGBE_QLAST_RESO if the routine uses the last Tx resource. + * KWGBE_OK otherwise. + */ +static enum kwgbe_fret_sts port_send(struct kwgbe_device *dkwgbe, + enum kwgbe_q tx_queue, + struct kwgbe_pktinf *p_pkt_info) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + struct kwgbe_registers *regs = dkwgbe->regs; + volatile struct kwgbe_tx_dscr *p_tx_desc_first; + volatile struct kwgbe_tx_dscr *p_tx_desc_curr; + volatile struct kwgbe_tx_dscr *p_tx_next_desc_curr; + volatile struct kwgbe_tx_dscr *p_tx_desc_used; + u32 command_status; + +#ifdef CONFIG_TX_PKT_DISPLAY + { + u16 pcnt = p_pkt_info->byte_cnt; + u8 *prnt = (u8 *) p_pkt_info->buf_ptr; + printf("cnt=%d,", pcnt); + while (pcnt) { + printf("%02x,", prnt[0]); + prnt++; + pcnt--; + } + printf(" pckend\n"); + } +#endif + /* Do not process Tx ring in case of Tx ring resource error */ + if (p_gbe_pctrl->tx_resource_err[tx_queue] == 1) + return KWGBE_QFULL; + + /* Get the Tx Desc ring indexes */ + CURR_TFD_GET(p_tx_desc_curr, tx_queue); + USED_TFD_GET(p_tx_desc_used, tx_queue); + + if (p_tx_desc_curr == NULL) + return KWGBE_ERROR; + + /* The following parameters are used to save readings from memory */ + p_tx_next_desc_curr = TX_NEXT_DESC_PTR(p_tx_desc_curr, tx_queue); + command_status = + p_pkt_info->cmd_sts | KWGBE_ZERO_PADDING | KWGBE_GEN_CRC; + + if (command_status & (KWGBE_TX_FIRST_DESC)) { + /* Update first desc */ + FIRST_TFD_SET(p_tx_desc_curr, tx_queue); + p_tx_desc_first = p_tx_desc_curr; + } else { + FIRST_TFD_GET(p_tx_desc_first, tx_queue); + command_status |= KWGBE_BUFFER_OWNED_BY_DMA; + } + + /* + * Buffers with a payload smaller than 8 bytes must be aligned to 64-bit + * boundary. We use the memory allocated for Tx descriptor. This memory + * located in TX_BUF_OFFSET_IN_DESC offset within the Tx descriptor. + */ + if (p_pkt_info->byte_cnt <= 8) { + printf("You have failed in the < 8 bytes errata - fixme\n"); + return KWGBE_ERROR; + + p_tx_desc_curr->buf_ptr = + (u32) p_tx_desc_curr + TX_BUF_OFFSET_IN_DESC; + b_copy(p_pkt_info->buf_ptr, p_tx_desc_curr->buf_ptr, + p_pkt_info->byte_cnt); + } else + p_tx_desc_curr->buf_ptr = p_pkt_info->buf_ptr; + + p_tx_desc_curr->byte_cnt = p_pkt_info->byte_cnt; + p_tx_desc_curr->retinfo = p_pkt_info->retinfo; + + if (p_pkt_info->cmd_sts & (KWGBE_TX_LAST_DESC)) { + /* Set last desc with DMA ownership and interrupt enable. */ + p_tx_desc_curr->cmd_sts = command_status | + KWGBE_BUFFER_OWNED_BY_DMA | KWGBE_TX_EN_INTERRUPT; + + if (p_tx_desc_curr != p_tx_desc_first) + p_tx_desc_first->cmd_sts |= KWGBE_BUFFER_OWNED_BY_DMA; + + /* Flush CPU pipe */ + D_CACHE_FLUSH_LINE((u32) p_tx_desc_curr, 0); + D_CACHE_FLUSH_LINE((u32) p_tx_desc_first, 0); + CPU_PIPE_FLUSH; + + /* Apply send command */ + KWGBEREG_WR(regs->tqc, (1 << tx_queue)); + debug("packet xmitted\n"); + + /* + * Finish Tx packet. + * Update first desc in case of Tx resource error + */ + p_tx_desc_first = p_tx_next_desc_curr; + FIRST_TFD_SET(p_tx_desc_first, tx_queue); + + } else { + p_tx_desc_curr->cmd_sts = command_status; + D_CACHE_FLUSH_LINE((u32) p_tx_desc_curr, 0); + } + + /* Check for ring index overlap in the Tx desc ring */ + if (p_tx_next_desc_curr == p_tx_desc_used) { + /* Update the current descriptor */ + CURR_TFD_SET(p_tx_desc_first, tx_queue); + + p_gbe_pctrl->tx_resource_err[tx_queue] = 1; + return KWGBE_QLAST_RESO; + } else { + /* Update the current descriptor */ + CURR_TFD_SET(p_tx_next_desc_curr, tx_queue); + return KWGBE_OK; + } +} + +/* + * tx_return_desc - Free all used Tx descriptors + * + * This routine returns the transmitted packet information to the caller. + * It uses the 'first' index to support Tx desc return in case a transmit + * of a packet spanned over multiple buffer still in process. + * In case the Tx queue was in "resource error" condition, where there are + * no available Tx resources, the function resets the resource error flag. + * + * @p_gbe_pctrl Ethernet Port Control srtuct ptr. + * @tx_queue Number of Tx queue. + * @p_pkt_info User packet buffer ptr. + * + * OUTPUT:Tx ring 'first' and 'used' indexes are updated. + * + * RETURN: + * KWGBE_ERROR in case the routine can not access Tx desc ring. + * KWGBE_RETRY in case there is transmission in process. + * KWGBE_END_OF_JOB if the routine has nothing to release. + * KWGBE_OK otherwise. + */ +static enum kwgbe_fret_sts tx_return_desc(struct kwgbe_device *dkwgbe, + enum kwgbe_q tx_queue, + struct kwgbe_pktinf *p_pkt_info) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + volatile struct kwgbe_tx_dscr *p_tx_desc_used = NULL; + volatile struct kwgbe_tx_dscr *p_tx_desc_first = NULL; + u32 command_status; + + /* Get the Tx Desc ring indexes */ + USED_TFD_GET(p_tx_desc_used, tx_queue); + FIRST_TFD_GET(p_tx_desc_first, tx_queue); + + /* Sanity check */ + if (p_tx_desc_used == NULL) + return KWGBE_ERROR; + + command_status = p_tx_desc_used->cmd_sts; + + /* Still transmitting... */ + if (command_status & (KWGBE_BUFFER_OWNED_BY_DMA)) { + D_CACHE_FLUSH_LINE((u32) p_tx_desc_used, 0); + return KWGBE_RETRY; + } + + /* Stop release. About to overlap the current available Tx descriptor */ + if ((p_tx_desc_used == p_tx_desc_first) && + (p_gbe_pctrl->tx_resource_err[tx_queue] == 0)) { + D_CACHE_FLUSH_LINE((u32) p_tx_desc_used, 0); + return KWGBE_END_OF_JOB; + } + + /* Pass the packet information to the caller */ + p_pkt_info->cmd_sts = command_status; + p_pkt_info->retinfo = p_tx_desc_used->retinfo; + p_tx_desc_used->retinfo = 0; + + /* Update the next descriptor to release. */ + USED_TFD_SET(TX_NEXT_DESC_PTR(p_tx_desc_used, tx_queue), tx_queue); + + /* Any Tx return cancels the Tx resource error status */ + if (p_gbe_pctrl->tx_resource_err[tx_queue] == 1) + p_gbe_pctrl->tx_resource_err[tx_queue] = 0; + + D_CACHE_FLUSH_LINE((u32) p_tx_desc_used, 0); + + return KWGBE_OK; +} + +/* + * port_receive - Get received information from Rx ring. + * + * This routine returns the received data to the caller. There is no + * data copying during routine operation. All information is returned + * using pointer to packet information struct passed from the caller. + * If the routine exhausts Rx ring resources then the resource error flag + * is set. + * + * @p_gbe_pctrl Ethernet Port Control srtuct ptr. + * @rx_queue Number of Rx queue. + * @p_pkt_info User packet buffer. + * + * OUTPUT: Rx ring current and used indexes are updated. + * + * RETURN: + * KWGBE_ERROR in case the routine can not access Rx desc ring. + * KWGBE_QFULL if Rx ring resources are exhausted. + * KWGBE_END_OF_JOB if there is no received data. + * KWGBE_OK otherwise. + */ +static enum kwgbe_fret_sts port_receive(struct kwgbe_device *dkwgbe, + enum kwgbe_q rx_queue, + struct kwgbe_pktinf *p_pkt_info) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + volatile struct kwgbe_rx_dscr *p_rx_curr_desc; + volatile struct kwgbe_rx_dscr *p_rx_next_curr_desc; + volatile struct kwgbe_rx_dscr *p_rx_used_desc; + u32 command_status; + + /* Do not process Rx ring in case of Rx ring resource error */ + if (p_gbe_pctrl->rx_resource_err[rx_queue] == 1) { + printf("Rx Queue is full ...\n"); + return KWGBE_QFULL; + } + + /* Get the Rx Desc ring 'curr and 'used' indexes */ + CURR_RFD_GET(p_rx_curr_desc, rx_queue); + USED_RFD_GET(p_rx_used_desc, rx_queue); + + /* Sanity check */ + if (p_rx_curr_desc == NULL) + return KWGBE_ERROR; + + /* The following parameters are used to save readings from memory */ + p_rx_next_curr_desc = RX_NEXT_DESC_PTR(p_rx_curr_desc, rx_queue); + command_status = p_rx_curr_desc->cmd_sts; + + /* Nothing to receive... */ + if (command_status & (KWGBE_BUFFER_OWNED_BY_DMA)) { + /*debug("Rx: command_status: %08x\n", command_status); */ + D_CACHE_FLUSH_LINE((u32) p_rx_curr_desc, 0); + /*debug("KWGBE_END_OF_JOB ...\n"); */ + return KWGBE_END_OF_JOB; + } + + p_pkt_info->byte_cnt = (p_rx_curr_desc->byte_cnt) - RX_BUF_OFFSET; + p_pkt_info->cmd_sts = command_status; + p_pkt_info->buf_ptr = (p_rx_curr_desc->buf_ptr) + RX_BUF_OFFSET; + p_pkt_info->retinfo = p_rx_curr_desc->retinfo; + p_pkt_info->l4i_chk = p_rx_curr_desc->buf_size; /* IP fragment indicator */ + + /* Clean the return info field to indicate that the packet has been */ + /* moved to the upper layers */ + p_rx_curr_desc->retinfo = 0; + + /* Update 'curr' in data structure */ + CURR_RFD_SET(p_rx_next_curr_desc, rx_queue); + + /* Rx descriptors resource exhausted. Set the Rx ring resource error flag */ + if (p_rx_next_curr_desc == p_rx_used_desc) + p_gbe_pctrl->rx_resource_err[rx_queue] = 1; + + D_CACHE_FLUSH_LINE((u32) p_rx_curr_desc, 0); + CPU_PIPE_FLUSH; + return KWGBE_OK; +} + +/* + * rx_return_buff - Returns a Rx buffer back to the Rx ring. + * + * This routine returns a Rx buffer back to the Rx ring. It retrieves the + * next 'used' descriptor and attached the returned buffer to it. + * In case the Rx ring was in "resource error" condition, where there are + * no available Rx resources, the function resets the resource error flag. + * + * @p_gbe_pctrl Ethernet Port Control srtuct ptr. + * @rx_queue Number of Rx queue. + * @p_pkt_info Information on the returned buffer ptr. + * + * OUTPUT: New available Rx resource in Rx descriptor ring. + * + * RETURN: + * KWGBE_ERROR in case the routine can not access Rx desc ring. + * KWGBE_OK otherwise. + */ +static enum kwgbe_fret_sts rx_return_buff(struct kwgbe_device *dkwgbe, + enum kwgbe_q rx_queue, + struct kwgbe_pktinf *p_pkt_info) +{ + struct kwgbe_portinfo *p_gbe_pctrl = &dkwgbe->portinfo; + volatile struct kwgbe_rx_dscr *p_used_rx_desc; /* Where to return Rx resource */ + + /* Get 'used' Rx descriptor */ + USED_RFD_GET(p_used_rx_desc, rx_queue); + + /* Sanity check */ + if (p_used_rx_desc == NULL) + return KWGBE_ERROR; + + p_used_rx_desc->buf_ptr = p_pkt_info->buf_ptr; + p_used_rx_desc->retinfo = p_pkt_info->retinfo; + p_used_rx_desc->byte_cnt = p_pkt_info->byte_cnt; + p_used_rx_desc->buf_size = KW_RX_BUF_SZ; /* Reset Buffer size */ + + /* Flush the write pipe */ + CPU_PIPE_FLUSH; + + /* Return the descriptor to DMA ownership */ + p_used_rx_desc->cmd_sts = + KWGBE_BUFFER_OWNED_BY_DMA | KWGBE_RX_EN_INTERRUPT; + + /* Flush descriptor and CPU pipe */ + D_CACHE_FLUSH_LINE((u32) p_used_rx_desc, 0); + CPU_PIPE_FLUSH; + + /* Move the used descriptor pointer to the next descriptor */ + USED_RFD_SET(RX_NEXT_DESC_PTR(p_used_rx_desc, rx_queue), rx_queue); + + /* Any Rx return cancels the Rx resource error status */ + if (p_gbe_pctrl->rx_resource_err[rx_queue] == 1) + p_gbe_pctrl->rx_resource_err[rx_queue] = 0; + + return KWGBE_OK; +} + +/* + * init function + */ +static int kwgbe_init(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct kwgbe_portinfo *portinfo = &dkwgbe->portinfo; + struct egiga_priv *portpriv = &dkwgbe->portpriv; + + u32 queue; + + /* + * ronen - when we update the MAC env params we only update dev->enetaddr + * see ./net/eth.c set_enetaddr() + */ + memcpy(portinfo->port_mac_addr, dev->enetaddr, 6); + + /* Activate the DMA channels etc */ + port_init(dkwgbe); + + /* "Allocate" setup TX rings */ + for (queue = 0; queue < KW_TXQ_NO; queue++) { + u32 size; + + portpriv->tx_ring_size[queue] = KW_TXQ_SZ; + /*size = no of DESCs times DESC-size */ + size = (portpriv->tx_ring_size[queue] * TX_DESC_ALIGNED_SIZE); + portinfo->tx_desc_area_size[queue] = size; + + /* first clear desc area completely */ + memset((void *)portinfo->p_tx_desc_area_base[queue], + 0, portinfo->tx_desc_area_size[queue]); + + /* initialize tx desc ring with low level driver */ + if (kwgbe_init_tx_desc_ring + (dkwgbe, KWGBE_Q0, + portpriv->tx_ring_size[queue], + KW_TX_BUF_SZ /* Each Buffer is 1600 Byte */ , + (u32) portinfo-> + p_tx_desc_area_base[queue], + (u32) portinfo->p_tx_buffer_base[queue]) == 0) + printf("### initializing TX Ring\n"); + } + + /* "Allocate" setup RX rings */ + for (queue = 0; queue < KW_RXQ_NO; queue++) { + u32 size; + + /* Meantime RX Ring are fixed - but must be configurable by user */ + portpriv->rx_ring_size[queue] = KW_RXQ_SZ; + size = (portpriv->rx_ring_size[queue] * RX_DESC_ALIGNED_SIZE); + portinfo->rx_desc_area_size[queue] = size; + + /* first clear desc area completely */ + memset((void *)portinfo->p_rx_desc_area_base[queue], + 0, portinfo->rx_desc_area_size[queue]); + if ((kwgbe_init_rx_desc_ring + (dkwgbe, KWGBE_Q0, + portpriv->rx_ring_size[queue], + KW_RX_BUF_SZ /* Each Buffer is 1600 Byte */ , + (u32) portinfo-> + p_rx_desc_area_base[queue], + (u32) portinfo->p_rx_buffer_base[queue])) == 0) + printf("### initializing RX Ring\n"); + } + + port_start(dkwgbe); + +#if (defined (CONFIG_MII) || defined (CONFIG_CMD_MII)) \ + && defined (CONFIG_SYS_FAULT_ECHO_LINK_DOWN) + if (!miiphy_link(dev->name, portinfo->port_phy_addr)) { + printf("No link on %s\n", dev->name); + return 0; + } +#endif + portpriv->running = MAGIC_KWGBE_RUNNING; + return 1; +} + +/* + * egiga_start_xmit + * + * This function is queues a packet in the Tx descriptor for + * required port. + * + * Output : zero upon success + */ +int kwgbe_xmit(struct eth_device *dev, volatile void *dataPtr, int dataSize) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct egiga_priv *portpriv = &dkwgbe->portpriv; + struct net_device_stats *stats = &portpriv->stats; + + struct kwgbe_pktinf pkt_info; + enum kwgbe_fret_sts status; + enum kwgbe_fret_sts release_result; + + /* Update packet info data structure */ + pkt_info.cmd_sts = KWGBE_TX_FIRST_DESC | KWGBE_TX_LAST_DESC; /* first last */ + pkt_info.cmd_sts |= KWGBE_BUFFER_OWNED_BY_DMA; /* DMA owned */ + + pkt_info.byte_cnt = dataSize; + pkt_info.buf_ptr = (u32) dataPtr; + pkt_info.retinfo = 0; + + status = port_send(dkwgbe, KWGBE_Q0, &pkt_info); + if ((status == KWGBE_ERROR) || (status == KWGBE_QFULL)) { + printf("On transmitting packet ..\n"); + if (status == KWGBE_QFULL) + printf("ETH Queue is full.\n"); + if (status == KWGBE_QLAST_RESO) + printf("ETH Queue: using last available resource.\n"); + goto error; + } + + /* Update statistics and start of transmittion time */ + stats->tx_bytes += dataSize; + stats->tx_packets++; + + /* Check if packet(s) is(are) transmitted correctly (release everything) */ + do { + release_result = tx_return_desc(dkwgbe, KWGBE_Q0, &pkt_info); + switch (release_result) { + case KWGBE_OK: + debug("descriptor released\n"); + if (pkt_info.cmd_sts & 1) { + printf("in TX\n"); + stats->tx_errors++; + } + break; + case KWGBE_RETRY: + debug("transmission still in process\n"); + break; + case KWGBE_ERROR: + printf("routine can not access Tx desc ring\n"); + break; + case KWGBE_END_OF_JOB: + debug("the routine has nothing to release\n"); + break; + default: /* should not happen */ + break; + } + } while (release_result == KWGBE_OK); + + return 0; /* success */ + error: + return 1; /* Failed - higher layers will free the skb */ +} + +/* + * kwgbe_receive + * + * This function is forward packets that are received from the port's + * queues toward kernel core or FastRoute them to another interface. + * + * @dev a pointer to the required interface + * + * Output : number of served packets + */ +int kwgbe_receive(struct eth_device *dev) +{ + struct kwgbe_device *dkwgbe = to_dkwgbe(dev); + struct egiga_priv *portpriv = &dkwgbe->portpriv; + struct net_device_stats *stats = &portpriv->stats; + struct kwgbe_pktinf pkt_info; + + while ((port_receive(dkwgbe, KWGBE_Q0, &pkt_info) == KWGBE_OK)) { + + if (pkt_info.byte_cnt != 0) { + debug("%s: Received %d byte Packet @ 0x%x", + __FUNCTION__, pkt_info.byte_cnt, + pkt_info.buf_ptr); + } + /* Update statistics. Note byte count includes 4 byte CRC count */ + stats->rx_packets++; + stats->rx_bytes += pkt_info.byte_cnt; + + /* + * In case received a packet without first / last bits on OR the error + * summary bit is on, the packets needs to be dropeed. + */ + if (((pkt_info. + cmd_sts & (KWGBE_RX_FIRST_DESC | KWGBE_RX_LAST_DESC)) != + (KWGBE_RX_FIRST_DESC | KWGBE_RX_LAST_DESC)) + || (pkt_info.cmd_sts & KWGBE_ERROR_SUMMARY)) { + stats->rx_dropped++; + + printf + ("Received packet spread on multiple descriptors\n"); + + /* Is this caused by an error ? */ + if (pkt_info.cmd_sts & KWGBE_ERROR_SUMMARY) { + stats->rx_errors++; + } + + /* free these descriptors again without forwarding them to the higher layers */ + pkt_info.buf_ptr &= ~0x7; /* realign buffer again */ + pkt_info.byte_cnt = 0x0000; /* Reset Byte count */ + + if (rx_return_buff(dkwgbe, KWGBE_Q0, &pkt_info) != + KWGBE_OK) { + printf + ("Error while returning the RX Desc to Ring\n"); + } else { + debug("RX Desc returned to Ring"); + } + /* /free these descriptors again */ + } else { + + /* !!! call higher layer processing */ + debug + ("\nNow send it to upper layer protocols (NetReceive) ..."); + + /* let the upper layer handle the packet */ + NetReceive((uchar *) pkt_info.buf_ptr, + (int)pkt_info.byte_cnt); + + /* free descriptor */ + pkt_info.buf_ptr &= ~0x7; /* realign buffer again */ + pkt_info.byte_cnt = 0x0000; /* Reset Byte count */ + debug("RX: pkt_info.buf_ptr = %x", pkt_info.buf_ptr); + if (rx_return_buff(dkwgbe, KWGBE_Q0, &pkt_info) != + KWGBE_OK) { + printf("while returning the RX Desc to Ring"); + } else { + debug("RX Desc returned to Ring"); + } + /* free descriptor code end */ + } + } + egiga_get_stats(dev); /* update statistics */ + return 1; +} + +/* + * Called from net/eth.c + */ +int kirkwood_egiga_initialize(bd_t * bis) +{ + struct kwgbe_device *dkwgbe; + struct eth_device *dev; + struct kwgbe_portinfo *portinfo; + struct egiga_priv *portpriv; + int devnum, x, temp; + char *s, *e, buf[64]; + u8 used_ports[MAX_KWGBE_DEVS] = CONFIG_KIRKWOOD_EGIGA_PORTS; + + for (devnum = 0; devnum < MAX_KWGBE_DEVS; devnum++) { + /*skip if port is configured not to use */ + if (used_ports[devnum] == 0) + continue; + + dkwgbe = malloc(sizeof(struct kwgbe_device)); + if (!dkwgbe) { + printf("Error: Failed to allocate memory for kwgbe%d\n", + devnum); + return -1; + } + memset(dkwgbe, 0, sizeof(struct kwgbe_device)); + + dev = &dkwgbe->dev; + portinfo = &dkwgbe->portinfo; + portpriv = &dkwgbe->portpriv; + + /* must be less than NAMESIZE (16) */ + sprintf(dev->name, "egiga%d", devnum); + debug("Initializing %s", dev->name); + + /* Extract the MAC address from the environment */ + switch (devnum) { + case 0: + dkwgbe->regs = (void *)KW_EGIGA0_BASE; + s = "ethaddr"; + break; + case 1: + dkwgbe->regs = (void *)KW_EGIGA1_BASE; + s = "eth1addr"; + break; + default: /* this should never happen */ + printf("%s: Invalid device number %d\n", + __FUNCTION__, devnum); + return -1; + } + + e = getenv(s); + if (!e) { + /* Generate Ramdom MAC addresses if not set */ + sprintf(buf, "00:50:43:%02x:%02x:%02x", + get_random_hex(), get_random_hex(), + get_random_hex()); + setenv(s, buf); + } + + temp = getenv_r(s, buf, sizeof(buf)); + s = (temp > 0) ? buf : NULL; + + debug("Setting MAC %d to %s", devnum, s); + /* on POR port is pre-powered up, so assume it is up */ + + for (x = 0; x < 6; ++x) { + dev->enetaddr[x] = s ? simple_strtoul(s, &e, 16) : 0; + if (s) + s = (*e) ? e + 1 : e; + } + /* set the MAC addr in the HW */ + memcpy(portinfo->port_mac_addr, dev->enetaddr, 6); + port_uc_addr_set(dkwgbe->regs, dev->enetaddr, 0); + + dev->init = (void *)kwgbe_init; + dev->halt = (void *)kwgbe_stop; + dev->send = (void *)kwgbe_xmit; + dev->recv = (void *)kwgbe_receive; + + /* + * Read MIB counter on the GT in order to reset them, + * then zero all the stats fields in memory + */ + egiga_update_stat(dev); + memset(&portpriv->stats, 0, sizeof(struct net_device_stats)); + + debug("Allocating descriptor and buffer rings"); + + portinfo->p_rx_desc_area_base[0] = + (struct kwgbe_rx_dscr *)memalign(16, + RX_DESC_ALIGNED_SIZE * + KW_RXQ_SZ + 1); + portinfo->p_tx_desc_area_base[0] = + (struct kwgbe_tx_dscr *)memalign(16, + TX_DESC_ALIGNED_SIZE * + KW_TXQ_SZ + 1); + + portinfo->p_rx_buffer_base[0] = + (char *)memalign(16, KW_RXQ_SZ * KW_TX_BUF_SZ + 1); + portinfo->p_tx_buffer_base[0] = + (char *)memalign(16, KW_RXQ_SZ * KW_TX_BUF_SZ + 1); + + eth_register(dev); + + /* Set phy address of the port */ + portinfo->port_phy_addr = PHY_BASE_ADR + devnum; + phy_set_addr(dkwgbe->regs, portinfo->port_phy_addr); + +#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) + miiphy_register(dev->name, smi_reg_read, smi_reg_write); +#endif + } + return 0; +} diff --git a/drivers/net/kirkwood_egiga.h b/drivers/net/kirkwood_egiga.h new file mode 100644 index 0000000..3a5a306 --- /dev/null +++ b/drivers/net/kirkwood_egiga.h @@ -0,0 +1,828 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar prafulla@marvell.com + * + * based on - Driver for MV64360X ethernet ports + * Copyright (C) 2002 rabeeh@galileo.co.il + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef __EGIGA_H__ +#define __EGIGA_H__ + +#define MAX_KWGBE_DEVS 2 /*controller has two ports */ + +/* PHY_BASE_ADR is board specific and can be configured */ +#if defined (CONFIG_PHY_BASE_ADR) +#define PHY_BASE_ADR CONFIG_PHY_BASE_ADR +#else +#define PHY_BASE_ADR 0x08 /* default phy base addr */ +#endif + +/* Egiga driver statistics can be displayed optionally */ +#ifdef CONFIG_EGIGA_STATS_BY_SOFTWARE +#define UPDATE_STATS_BY_SOFTWARE +#else +#undef UPDATE_STATS_BY_SOFTWARE +#endif + +/* Constants */ +#define MAGIC_KWGBE_RUNNING 8031971 +#define INT_CAUSE_UNMASK_ALL 0x0007ffff +#define INT_CAUSE_UNMASK_ALL_EXT 0x0011ffff + +/* Port attrib */ +/* Max queue number is 8 for controller but here configured 1 */ +#define MAX_RXQ_NO 1 +#define MAX_TXQ_NO 1 +/* Use one TX queue and one RX queue */ +#define KW_TXQ_NO 1 +#define KW_RXQ_NO 1 + +/* + * Number of RX / TX descriptors on RX / TX rings. + * Note that allocating RX descriptors is done by allocating the RX + * ring AND a preallocated RX buffers (skb's) for each descriptor. + * The TX descriptors only allocates the TX descriptors ring, + * with no pre allocated TX buffers (skb's are allocated by higher layers. + */ + +/* TX/RX parameters can be passed externally */ +#ifdef CONFIG_KWGBE_TXQ_SZ +#define KW_TXQ_SZ CONFIG_KWGBE_TXQ_SZ +#else +#define KW_TXQ_SZ 4 +#endif + +#ifdef CONFIG_KWGBE_RXQ_SZ +#define KW_RXQ_SZ CONFIG_KWGBE_RXQ_SZ +#else +#define KW_RXQ_SZ 4 +#endif + +#ifdef CONFIG_KWGBE_RXBUF_SZ +#define KW_RX_BUF_SZ CONFIG_KWGBE_RXBUF_SZ +#else +#define KW_RX_BUF_SZ 1600 +#endif + +#ifdef CONFIG_KWGBE_TXBUF_SZ +#define KW_TX_BUF_SZ CONFIG_KWGBE_TXBUF_SZ +#else +#define KW_TX_BUF_SZ 1600 +#endif + +#define RX_BUF_MXSZ 0xFFFF +#define TX_BUF_MXSZ 0xFFFF /* Buffers are limited to 64k */ +#define RX_BUF_MNSZ 0x8 +#define TX_BUF_MNSZ 0x8 + +/* + * Network device statistics. Akin to the 2.0 ether stats but + * with byte counters. + */ +struct net_device_stats { + u32 rx_packets; /* total packets received */ + u32 tx_packets; /* total packets transmitted */ + u64 rx_bytes; /* total bytes received */ + u64 tx_bytes; /* total bytes transmitted */ + u32 rx_errors; /* bad packets received */ + u32 tx_errors; /* packet transmit problems */ + u32 rx_dropped; /* no space in linux buffers */ + u32 tx_dropped; /* no space available in linux */ + u32 multicast; /* multicast packets received */ + u32 collisions; + /* detailed rx_errors: */ + u32 rx_length_errors; + u32 rx_over_errors; /* receiver ring buff overflow */ + u32 rx_crc_errors; /* recved pkt with crc error */ + u32 rx_frame_errors; /* recv'd frame alignment error */ + u32 rx_fifo_errors; /* recv'r fifo overrun */ + u32 rx_missed_errors; /* receiver missed packet */ + /* detailed tx_errors */ + u32 tx_aborted_errors; + u32 tx_carrier_errors; + u32 tx_fifo_errors; + u32 tx_heartbeat_errors; + u32 tx_window_errors; + /* for cslip etc */ + u32 rx_compressed; + u32 tx_compressed; +}; + +/* Private data structure used for ethernet device */ +struct egiga_priv { + struct net_device_stats stats; + /* to buffer area aligned */ + char *p_tx_buffer[KW_TXQ_SZ + 1]; + char *p_rx_buffer[KW_RXQ_SZ + 1]; + /* Size of Tx Ring per queue */ + u32 tx_ring_size[MAX_TXQ_NO]; + /* Size of Rx Ring per queue */ + u32 rx_ring_size[MAX_RXQ_NO]; + /* Magic Number for Ethernet running */ + u32 running; +}; + +/* Chip Registers Structures */ +struct mib_counters { + u64 good_octets_received; + u32 bad_octets_received; + u32 internal_mac_transmit_err; + u32 good_frames_received; + u32 bad_frames_received; + u32 broadcast_frames_received; + u32 multicast_frames_received; + u32 frames_64_octets; + u32 frames_65_to_127_octets; + u32 frames_128_to_255_octets; + u32 frames_256_to_511_octets; + u32 frames_512_to_1023_octets; + u32 frames_1024_to_max_octets; + u64 good_octets_sent; + u32 good_frames_sent; + u32 excessive_collision; + u32 multicast_frames_sent; + u32 broadcast_frames_sent; + u32 unrec_mac_control_received; + u32 fc_sent; + u32 good_fc_received; + u32 bad_fc_received; + u32 undersize_received; + u32 fragments_received; + u32 oversize_received; + u32 jabber_received; + u32 mac_receive_error; + u32 bad_crc_event; + u32 collision; + u32 late_collision; +}; + +struct kwgbe_barsz { + u32 bar; + u32 size; +}; + +struct kwgbe_crdp { + u32 crdp; + u32 crdp_pad[3]; +}; + +struct kwgbe_tqx { + u32 qxttbc; + u32 tqxtbc; + u32 tqxac; + u32 tqxpad; +}; + +struct kwgbe_registers { + u32 phyadr; + u32 smi; + u32 euda; + u32 eudid; + u8 pad1[0x080 - 0x00c - 4]; + u32 euic; + u32 euim; + u8 pad2[0x094 - 0x084 - 4]; + u32 euea; + u32 euiae; + u8 pad3[0x0b0 - 0x098 - 4]; + u32 euc; + u8 pad3a[0x200 - 0x0b0 - 4]; + struct kwgbe_barsz barsz[6]; + u8 pad4[0x280 - 0x22c - 4]; + u32 ha_remap[4]; + u32 bare; + u32 epap; + u8 pad5[0x400 - 0x294 - 4]; + u32 pxc; + u32 pxcx; + u32 mii_ser_params; + u8 pad6[0x410 - 0x408 - 4]; + u32 evlane; + u32 macal; + u32 macah; + u32 sdc; + u32 dscp[7]; + u32 psc0; + u32 vpt2p; + u32 ps0; + u32 tqc; + u32 psc1; + u32 ps1; + u32 mrvl_header; + u8 pad7[0x460 - 0x454 - 4]; + u32 ic; + u32 ice; + u32 pim; + u32 peim; + u8 pad8[0x474 - 0x46c - 4]; + u32 pxtfut; + u32 pad9; + u32 pxmfs; + u32 pad10; + u32 pxdfc; + u32 pxofc; + u8 pad11[0x494 - 0x488 - 4]; + u32 peuiae; + u8 pad12[0x4bc - 0x494 - 4]; + u32 eth_type_prio; + u8 pad13[0x4dc - 0x4bc - 4]; + u32 tqfpc; + u32 pttbrc; + u32 tqc1; + u32 pmtu; + u32 pmtbs; + u8 pad14[0x60c - 0x4ec - 4]; + struct kwgbe_crdp crdp[7]; + u32 crdp7; + u32 rqc; + u32 cur_servd_dscr_ptr; + u8 pad15[0x6c0 - 0x684 - 4]; + u32 tcqdp[8]; + u8 pad16[0x700 - 0x6dc - 4]; + struct kwgbe_tqx tqx[8]; + u32 pttbc; + u8 pad17[0x7a8 - 0x780 - 4]; + u32 tqxipg0; + u32 pad18[3]; + u32 tqxipg1; + u8 pad19[0x7c0 - 0x7b8 - 4]; + u32 hitkninlopkt; + u32 hitkninasyncpkt; + u32 lotkninasyncpkt; + u32 pad20; + u32 ts; + u8 pad21[0x3000 - 0x27d0 - 4]; + struct mib_counters mibc; + u8 pad22[0x3400 - 0x3000 - sizeof(struct mib_counters)]; + u32 dfsmt[64]; + u32 dfomt[64]; + u32 dfut[4]; + u8 pad23[0xe20c0 - 0x7360c - 4]; + u32 pmbus_top_arbiter; +}; + +#define to_dkwgbe(_kd) container_of(_kd, struct kwgbe_device, dev) +#define KWGBEREG_WR(adr, val) writel(val, (u32)&adr) +#define KWGBEREG_RD(adr) readl((u32)&adr) +#define KWGBEREG_BITS_RESET(adr, val) writel(readl((u32)&adr) & ~(val), (u32)&adr) +#define KWGBEREG_BITS_SET(adr, val) writel(readl((u32)&adr) | val, (u32)&adr) + +/* Default port configuration value */ +#define PRT_CFG_VAL \ + KWGBE_UCAST_MOD_NRML | \ + KWGBE_DFLT_RX_Q0 | \ + KWGBE_DFLT_RX_ARPQ0 | \ + KWGBE_RX_BC_IF_NOT_IP_OR_ARP | \ + KWGBE_RX_BC_IF_IP | \ + KWGBE_RX_BC_IF_ARP | \ + KWGBE_CPTR_TCP_FRMS_DIS | \ + KWGBE_CPTR_UDP_FRMS_DIS | \ + KWGBE_DFLT_RX_TCPQ0 | \ + KWGBE_DFLT_RX_UDPQ0 | \ + KWGBE_DFLT_RX_BPDU_Q_0 + +/* Default port extend configuration value */ +#define PORT_CFG_EXTEND_VALUE \ + KWGBE_SPAN_BPDU_PACKETS_AS_NORMAL | \ + KWGBE_PARTITION_DIS | \ + KWGBE_TX_CRC_GENERATION_EN + +/* Default sdma control value */ +#ifdef CONFIG_NOT_COHERENT_CACHE +#define PORT_SDMA_CFG_VALUE \ + KWGBE_RX_BURST_SIZE_16_64BIT | \ + KWGBE_BLM_RX_NO_SWAP | \ + KWGBE_BLM_TX_NO_SWAP | \ + GT_KWGBE_IPG_INT_RX(0) | \ + KWGBE_TX_BURST_SIZE_16_64BIT; +#else +#define PORT_SDMA_CFG_VALUE \ + KWGBE_RX_BURST_SIZE_4_64BIT | \ + GT_KWGBE_IPG_INT_RX(0) | \ + KWGBE_TX_BURST_SIZE_4_64BIT; +#endif + +#define GT_KWGBE_IPG_INT_RX(value) ((value & 0x3fff) << 8) + +/* Default port serial control value */ +#define PORT_SERIAL_CONTROL_VALUE_TMP \ + KWGBE_FORCE_LINK_PASS | \ + KWGBE_DIS_AUTO_NEG_FOR_DUPLX | \ + KWGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \ + KWGBE_ADV_NO_FLOW_CTRL | \ + KWGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \ + KWGBE_FORCE_BP_MODE_NO_JAM | \ + (1 << 9) | \ + KWGBE_DO_NOT_FORCE_LINK_FAIL | \ + KWGBE_DIS_AUTO_NEG_SPEED_GMII | \ + KWGBE_DTE_ADV_0 | \ + KWGBE_MIIPHY_MAC_MODE | \ + KWGBE_AUTO_NEG_NO_CHANGE | \ + KWGBE_MAX_RX_PACKET_1552BYTE | \ + KWGBE_CLR_EXT_LOOPBACK | \ + KWGBE_SET_FULL_DUPLEX_MODE | \ + KWGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX | \ + KWGBE_SET_MII_SPEED_TO_100 + +#ifdef CONFIG_SYS_MII_MODE +#define PORT_SERIAL_CONTROL_VALUE \ + PORT_SERIAL_CONTROL_VALUE_TMP | \ + KWGBE_SET_GMII_SPEED_TO_10_100 +#else +#define PORT_SERIAL_CONTROL_VALUE \ + PORT_SERIAL_CONTROL_VALUE_TMP | \ + KWGBE_SET_GMII_SPEED_TO_1000 +#endif + +/* Tx WRR confoguration macros */ +#define PORT_MAX_TRAN_UNIT 0x24 /* MTU register (default) 9KByte */ +#define PORT_MAX_TOKEN_BUCKET_SIZE 0x_fFFF /* PMTBS reg (default) */ +#define PORT_TOKEN_RATE 1023 /* PTTBRC reg (default) */ +/* MAC accepet/reject macros */ +#define ACCEPT_MAC_ADDR 0 +#define REJECT_MAC_ADDR 1 +/* Size of a Tx/Rx descriptor used in chain list data structure */ +#define RX_DESC_ALIGNED_SIZE 0x20 +#define TX_DESC_ALIGNED_SIZE 0x20 +/* An offest in Tx descriptors to store data for buffers less than 8 Bytes */ +#define TX_BUF_OFFSET_IN_DESC 0x18 +/* Buffer offset from buffer pointer */ +#define RX_BUF_OFFSET 0x2 + +/* Port serial status reg (PSR) */ +#define KWGBE_INTERFACE_GMII_MII 0 +#define KWGBE_INTERFACE_PCM 1 +#define KWGBE_LINK_IS_DOWN 0 +#define KWGBE_LINK_IS_UP (1 << 1) +#define KWGBE_PORT_AT_HALF_DUPLEX 0 +#define KWGBE_PORT_AT_FULL_DUPLEX (1 << 2) +#define KWGBE_RX_FLOW_CTRL_DISD 0 +#define KWGBE_RX_FLOW_CTRL_ENBALED (1 << 3) +#define KWGBE_GMII_SPEED_100_10 0 +#define KWGBE_GMII_SPEED_1000 (1 << 4) +#define KWGBE_MII_SPEED_10 0 +#define KWGBE_MII_SPEED_100 (1 << 5) +#define KWGBE_NO_TX 0 +#define KWGBE_TX_IN_PROGRESS (1 << 7) +#define KWGBE_BYPASS_NO_ACTIVE 0 +#define KWGBE_BYPASS_ACTIVE (1 << 8) +#define KWGBE_PORT_NOT_AT_PARTN_STT 0 +#define KWGBE_PORT_AT_PARTN_STT (1 << 9) +#define KWGBE_PORT_TX_FIFO_NOT_EMPTY 0 +#define KWGBE_PORT_TX_FIFO_EMPTY (1 << 10) + +/* These macros describes the Port configuration reg (Px_cR) bits */ +#define KWGBE_UCAST_MOD_NRML 0 +#define KWGBE_UNICAST_PROMISCUOUS_MODE 1 +#define KWGBE_DFLT_RX_Q0 0 +#define KWGBE_DFLT_RX_Q1 (1 << 1) +#define KWGBE_DFLT_RX_Q2 (1 << 2) +#define KWGBE_DFLT_RX_Q3 ((1 << 2) | (1 << 1)) +#define KWGBE_DFLT_RX_Q4 (1 << 3) +#define KWGBE_DFLT_RX_Q5 ((1 << 3) | (1 << 1)) +#define KWGBE_DFLT_RX_Q6 ((1 << 3) | (1 << 2)) +#define KWGBE_DFLT_RX_Q7 ((1 << 3) | (1 << 2) | (1 << 1)) +#define KWGBE_DFLT_RX_ARPQ0 0 +#define KWGBE_DFLT_RX_ARPQ1 (1 << 4) +#define KWGBE_DFLT_RX_ARPQ2 (1 << 5) +#define KWGBE_DFLT_RX_ARPQ3 ((1 << 5) | (1 << 4)) +#define KWGBE_DFLT_RX_ARPQ4 (1 << 6) +#define KWGBE_DFLT_RX_ARPQ5 ((1 << 6) | (1 << 4)) +#define KWGBE_DFLT_RX_ARPQ6 ((1 << 6) | (1 << 5)) +#define KWGBE_DFLT_RX_ARPQ7 ((1 << 6) | (1 << 5) | (1 << 4)) +#define KWGBE_RX_BC_IF_NOT_IP_OR_ARP 0 +#define KWGBE_REJECT_BC_IF_NOT_IP_OR_ARP (1 << 7) +#define KWGBE_RX_BC_IF_IP 0 +#define KWGBE_REJECT_BC_IF_IP (1 << 8) +#define KWGBE_RX_BC_IF_ARP 0 +#define KWGBE_REJECT_BC_IF_ARP (1 << 9) +#define KWGBE_TX_AM_NO_UPDATE_ERR_SMRY (1 << 12) +#define KWGBE_CPTR_TCP_FRMS_DIS 0 +#define KWGBE_CPTR_TCP_FRMS_EN (1 << 14) +#define KWGBE_CPTR_UDP_FRMS_DIS 0 +#define KWGBE_CPTR_UDP_FRMS_EN (1 << 15) +#define KWGBE_DFLT_RX_TCPQ0 0 +#define KWGBE_DFLT_RX_TCPQ1 (1 << 16) +#define KWGBE_DFLT_RX_TCPQ2 (1 << 17) +#define KWGBE_DFLT_RX_TCPQ3 ((1 << 17) | (1 << 16)) +#define KWGBE_DFLT_RX_TCPQ4 (1 << 18) +#define KWGBE_DFLT_RX_TCPQ5 ((1 << 18) | (1 << 16)) +#define KWGBE_DFLT_RX_TCPQ6 ((1 << 18) | (1 << 17)) +#define KWGBE_DFLT_RX_TCPQ7 ((1 << 18) | (1 << 17) | (1 << 16)) +#define KWGBE_DFLT_RX_UDPQ0 0 +#define KWGBE_DFLT_RX_UDPQ1 (1 << 19) +#define KWGBE_DFLT_RX_UDPQ2 (1 << 20) +#define KWGBE_DFLT_RX_UDPQ3 ((1 << 20) | (1 << 19)) +#define KWGBE_DFLT_RX_UDPQ4 (1 << 21) +#define KWGBE_DFLT_RX_UDPQ5 ((1 << 21) | (1 << 19)) +#define KWGBE_DFLT_RX_UDPQ6 ((1 << 21) | (1 << 20)) +#define KWGBE_DFLT_RX_UDPQ7 ((1 << 21) | (1 << 20) | (1 << 19)) +#define KWGBE_DFLT_RX_BPDU_Q_0 0 +#define KWGBE_DFLT_RX_BPDU_Q_1 (1 << 22) +#define KWGBE_DFLT_RX_BPDU_Q_2 (1 << 23) +#define KWGBE_DFLT_RX_BPDU_Q_3 ((1 << 23) | (1 << 22)) +#define KWGBE_DFLT_RX_BPDU_Q_4 (1 << 24) +#define KWGBE_DFLT_RX_BPDU_Q_5 ((1 << 24) | (1 << 22)) +#define KWGBE_DFLT_RX_BPDU_Q_6 ((1 << 24) | (1 << 23)) +#define KWGBE_DFLT_RX_BPDU_Q_7 ((1 << 24) | (1 << 23) | (1 << 22)) +#define KWGBE_DFLT_RX_TCP_CHKSUM_MODE (1 << 25) + +/* These macros describes the Port configuration extend reg (Px_cXR) bits*/ +#define KWGBE_CLASSIFY_EN 1 +#define KWGBE_SPAN_BPDU_PACKETS_AS_NORMAL 0 +#define KWGBE_SPAN_BPDU_PACKETS_TO_RX_Q7 (1 << 1) +#define KWGBE_PARTITION_DIS 0 +#define KWGBE_PARTITION_EN (1 << 2) +#define KWGBE_TX_CRC_GENERATION_EN 0 +#define KWGBE_TX_CRC_GENERATION_DIS (1 << 3) + +/* Tx/Rx queue command reg (RQCR/TQCR)*/ +#define KWGBE_Q_0_EN 1 +#define KWGBE_Q_1_EN (1 << 1) +#define KWGBE_Q_2_EN (1 << 2) +#define KWGBE_Q_3_EN (1 << 3) +#define KWGBE_Q_4_EN (1 << 4) +#define KWGBE_Q_5_EN (1 << 5) +#define KWGBE_Q_6_EN (1 << 6) +#define KWGBE_Q_7_EN (1 << 7) +#define KWGBE_Q_0_DIS (1 << 8) +#define KWGBE_Q_1_DIS (1 << 9) +#define KWGBE_Q_2_DIS (1 << 10) +#define KWGBE_Q_3_DIS (1 << 11) +#define KWGBE_Q_4_DIS (1 << 12) +#define KWGBE_Q_5_DIS (1 << 13) +#define KWGBE_Q_6_DIS (1 << 14) +#define KWGBE_Q_7_DIS (1 << 15) + +/* These macros describes the Port Sdma configuration reg (SDCR) bits */ +#define KWGBE_RIFB 1 +#define KWGBE_RX_BURST_SIZE_1_64BIT 0 +#define KWGBE_RX_BURST_SIZE_2_64BIT (1 << 1) +#define KWGBE_RX_BURST_SIZE_4_64BIT (1 << 2) +#define KWGBE_RX_BURST_SIZE_8_64BIT ((1 << 2) | (1 << 1)) +#define KWGBE_RX_BURST_SIZE_16_64BIT (1 << 3) +#define KWGBE_BLM_RX_NO_SWAP (1 << 4) +#define KWGBE_BLM_RX_BYTE_SWAP 0 +#define KWGBE_BLM_TX_NO_SWAP (1 << 5) +#define KWGBE_BLM_TX_BYTE_SWAP 0 +#define KWGBE_DESCRIPTORS_BYTE_SWAP (1 << 6) +#define KWGBE_DESCRIPTORS_NO_SWAP 0 +#define KWGBE_TX_BURST_SIZE_1_64BIT 0 +#define KWGBE_TX_BURST_SIZE_2_64BIT (1 << 22) +#define KWGBE_TX_BURST_SIZE_4_64BIT (1 << 23) +#define KWGBE_TX_BURST_SIZE_8_64BIT ((1 << 23) | (1 << 22)) +#define KWGBE_TX_BURST_SIZE_16_64BIT (1 << 24) + +/* These macros describes the Port serial control reg (PSCR) bits */ +#define KWGBE_SERIAL_PORT_DIS 0 +#define KWGBE_SERIAL_PORT_EN 1 +#define KWGBE_FORCE_LINK_PASS (1 << 1) +#define KWGBE_DO_NOT_FORCE_LINK_PASS 0 +#define KWGBE_EN_AUTO_NEG_FOR_DUPLX 0 +#define KWGBE_DIS_AUTO_NEG_FOR_DUPLX (1 << 2) +#define KWGBE_EN_AUTO_NEG_FOR_FLOW_CTRL 0 +#define KWGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL (1 << 3) +#define KWGBE_ADV_NO_FLOW_CTRL 0 +#define KWGBE_ADV_SYMMETRIC_FLOW_CTRL (1 << 4) +#define KWGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX 0 +#define KWGBE_FORCE_FC_MODE_TX_PAUSE_DIS (1 << 5) +#define KWGBE_FORCE_BP_MODE_NO_JAM 0 +#define KWGBE_FORCE_BP_MODE_JAM_TX (1 << 7) +#define KWGBE_FORCE_BP_MODE_JAM_TX_ON_RX_ERR (1 << 8) +#define KWGBE_FORCE_LINK_FAIL 0 +#define KWGBE_DO_NOT_FORCE_LINK_FAIL (1 << 10) +#define KWGBE_DIS_AUTO_NEG_SPEED_GMII (1 << 13) +#define KWGBE_EN_AUTO_NEG_SPEED_GMII 0 +#define KWGBE_DTE_ADV_0 0 +#define KWGBE_DTE_ADV_1 (1 << 14) +#define KWGBE_MIIPHY_MAC_MODE 0 +#define KWGBE_MIIPHY_PHY_MODE (1 << 15) +#define KWGBE_AUTO_NEG_NO_CHANGE 0 +#define KWGBE_RESTART_AUTO_NEG (1 << 16) +#define KWGBE_MAX_RX_PACKET_1518BYTE 0 +#define KWGBE_MAX_RX_PACKET_1522BYTE (1 << 17) +#define KWGBE_MAX_RX_PACKET_1552BYTE (1 << 18) +#define KWGBE_MAX_RX_PACKET_9022BYTE ((1 << 18) | (1 << 17)) +#define KWGBE_MAX_RX_PACKET_9192BYTE (1 << 19) +#define KWGBE_MAX_RX_PACKET_9700BYTE ((1 << 19) | (1 << 17)) +#define KWGBE_SET_EXT_LOOPBACK (1 << 20) +#define KWGBE_CLR_EXT_LOOPBACK 0 +#define KWGBE_SET_FULL_DUPLEX_MODE (1 << 21) +#define KWGBE_SET_HALF_DUPLEX_MODE 0 +#define KWGBE_EN_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX (1 << 22) +#define KWGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX 0 +#define KWGBE_SET_GMII_SPEED_TO_10_100 0 +#define KWGBE_SET_GMII_SPEED_TO_1000 (1 << 23) +#define KWGBE_SET_MII_SPEED_TO_10 0 +#define KWGBE_SET_MII_SPEED_TO_100 (1 << 24) + +/* SMI register fields (KWGBE_SMI_REG) */ +#define KWGBE_PHY_SMI_TIMEOUT 10000 +#define KWGBE_PHY_SMI_DATA_OFFS 0 /* Data */ +#define KWGBE_PHY_SMI_DATA_MASK (0xffff << KWGBE_PHY_SMI_DATA_OFFS) +#define KWGBE_PHY_SMI_DEV_ADDR_OFFS 16 /* PHY device address */ +#define KWGBE_PHY_SMI_DEV_ADDR_MASK (0x1f << KWGBE_PHY_SMI_DEV_ADDR_OFFS) +#define KWGBE_SMI_REG_ADDR_OFFS 21 /* PHY device register address */ +#define KWGBE_SMI_REG_ADDR_MASK (0x1f << KWGBE_SMI_REG_ADDR_OFFS) +#define KWGBE_PHY_SMI_OPCODE_OFFS 26 /* Write/Read opcode */ +#define KWGBE_PHY_SMI_OPCODE_MASK (3 << KWGBE_PHY_SMI_OPCODE_OFFS) +#define KWGBE_PHY_SMI_OPCODE_WRITE (0 << KWGBE_PHY_SMI_OPCODE_OFFS) +#define KWGBE_PHY_SMI_OPCODE_READ (1 << KWGBE_PHY_SMI_OPCODE_OFFS) +#define KWGBE_PHY_SMI_READ_VALID_MASK (1 << 27) /* Read Valid */ +#define KWGBE_PHY_SMI_BUSY_MASK (1 << 28) /* Busy */ + +/* SDMA command status fields macros */ +/* Tx & Rx descriptors status */ +#define KWGBE_ERROR_SUMMARY 1 + +/* Tx & Rx descriptors command */ +#define KWGBE_BUFFER_OWNED_BY_DMA (1 << 31) + +/* Tx descriptors status */ +#define KWGBE_LC_ERROR 0 +#define KWGBE_UR_ERROR (1 << 1) +#define KWGBE_RL_ERROR (1 << 2) +#define KWGBE_LLC_SNAP_FORMAT (1 << 9) + +/* Rx descriptors status */ +#define KWGBE_CRC_ERROR 0 +#define KWGBE_OVERRUN_ERROR (1 << 1) +#define KWGBE_MAX_FRAME_LENGTH_ERROR (1 << 2) +#define KWGBE_RESOURCE_ERROR ((1 << 2) | (1 << 1)) +#define KWGBE_VLAN_TAGGED (1 << 19) +#define KWGBE_BPDU_FRAME (1 << 20) +#define KWGBE_TCP_FRAME_OVER_IP_V_4 0 +#define KWGBE_UDP_FRAME_OVER_IP_V_4 (1 << 21) +#define KWGBE_OTHER_FRAME_TYPE (1 << 22) +#define KWGBE_LAYER_2_IS_KWGBE_V_2 (1 << 23) +#define KWGBE_FRAME_TYPE_IP_V_4 (1 << 24) +#define KWGBE_FRAME_HEADER_OK (1 << 25) +#define KWGBE_RX_LAST_DESC (1 << 26) +#define KWGBE_RX_FIRST_DESC (1 << 27) +#define KWGBE_UNKNOWN_DESTINATION_ADDR (1 << 28) +#define KWGBE_RX_EN_INTERRUPT (1 << 29) +#define KWGBE_LAYER_4_CHECKSUM_OK (1 << 30) + +/* Rx descriptors byte count */ +#define KWGBE_FRAME_FRAGMENTED (1 << 2) + +/* Tx descriptors command */ +#define KWGBE_LAYER_4_CHECKSUM_FIRST_DESC (1 << 10) +#define KWGBE_FRAME_SET_TO_VLAN (1 << 15) +#define KWGBE_TCP_FRAME 0 +#define KWGBE_UDP_FRAME (1 << 16) +#define KWGBE_GEN_TCP_UDP_CHECKSUM (1 << 17) +#define KWGBE_GEN_IP_V_4_CHECKSUM (1 << 18) +#define KWGBE_ZERO_PADDING (1 << 19) +#define KWGBE_TX_LAST_DESC (1 << 20) +#define KWGBE_TX_FIRST_DESC (1 << 21) +#define KWGBE_GEN_CRC (1 << 22) +#define KWGBE_TX_EN_INTERRUPT (1 << 23) +#define KWGBE_AUTO_MODE (1 << 30) + +/* Address decode parameters */ +/* Ethernet Base Address Register bits */ +#define EBAR_TARGET_DRAM 0x00000000 +#define EBAR_TARGET_DEVICE 0x00000001 +#define EBAR_TARGET_CBS 0x00000002 +#define EBAR_TARGET_PCI0 0x00000003 +#define EBAR_TARGET_PCI1 0x00000004 +#define EBAR_TARGET_CUNIT 0x00000005 +#define EBAR_TARGET_AUNIT 0x00000006 +#define EBAR_TARGET_GUNIT 0x00000007 + +/* Window attrib */ +#define EBAR_ATTR_DRAM_CS0 0x00000E00 +#define EBAR_ATTR_DRAM_CS1 0x00000D00 +#define EBAR_ATTR_DRAM_CS2 0x00000B00 +#define EBAR_ATTR_DRAM_CS3 0x00000700 + +/* DRAM Target interface */ +#define EBAR_ATTR_DRAM_NO_CACHE_COHERENCY 0x00000000 +#define EBAR_ATTR_DRAM_CACHE_COHERENCY_WT 0x00001000 +#define EBAR_ATTR_DRAM_CACHE_COHERENCY_WB 0x00002000 + +/* Device Bus Target interface */ +#define EBAR_ATTR_DEVICE_DEVCS0 0x00001E00 +#define EBAR_ATTR_DEVICE_DEVCS1 0x00001D00 +#define EBAR_ATTR_DEVICE_DEVCS2 0x00001B00 +#define EBAR_ATTR_DEVICE_DEVCS3 0x00001700 +#define EBAR_ATTR_DEVICE_BOOTCS3 0x00000F00 + +/* PCI Target interface */ +#define EBAR_ATTR_PCI_BYTE_SWAP 0x00000000 +#define EBAR_ATTR_PCI_NO_SWAP 0x00000100 +#define EBAR_ATTR_PCI_BYTE_WORD_SWAP 0x00000200 +#define EBAR_ATTR_PCI_WORD_SWAP 0x00000300 +#define EBAR_ATTR_PCI_NO_SNOOP_NOT_ASSERT 0x00000000 +#define EBAR_ATTR_PCI_NO_SNOOP_ASSERT 0x00000400 +#define EBAR_ATTR_PCI_IO_SPACE 0x00000000 +#define EBAR_ATTR_PCI_MEMORY_SPACE 0x00000800 +#define EBAR_ATTR_PCI_REQ64_FORCE 0x00000000 +#define EBAR_ATTR_PCI_REQ64_SIZE 0x00001000 + +/* Window access control */ +#define EWIN_ACCESS_NOT_ALLOWED 0 +#define EWIN_ACCESS_READ_ONLY 1 +#define EWIN_ACCESS_FULL ((1 << 1) | 1) + +/* SDMA command macros */ +#define CURR_RFD_GET(p_curr_desc, queue) \ + ((p_curr_desc) = p_gbe_pctrl->p_rx_curr_desc_q[queue]) + +#define CURR_RFD_SET(p_curr_desc, queue) \ + (p_gbe_pctrl->p_rx_curr_desc_q[queue] = (p_curr_desc)) + +#define USED_RFD_GET(p_used_desc, queue) \ + ((p_used_desc) = p_gbe_pctrl->p_rx_used_desc_q[queue]) + +#define USED_RFD_SET(p_used_desc, queue)\ +(p_gbe_pctrl->p_rx_used_desc_q[queue] = (p_used_desc)) + +#define CURR_TFD_GET(p_curr_desc, queue) \ + ((p_curr_desc) = p_gbe_pctrl->p_tx_curr_desc_q[queue]) + +#define CURR_TFD_SET(p_curr_desc, queue) \ + (p_gbe_pctrl->p_tx_curr_desc_q[queue] = (p_curr_desc)) + +#define USED_TFD_GET(p_used_desc, queue) \ + ((p_used_desc) = p_gbe_pctrl->p_tx_used_desc_q[queue]) + +#define USED_TFD_SET(p_used_desc, queue) \ + (p_gbe_pctrl->p_tx_used_desc_q[queue] = (p_used_desc)) + +#define FIRST_TFD_GET(p_first_desc, queue) \ + ((p_first_desc) = p_gbe_pctrl->p_tx_first_desc_q[queue]) + +#define FIRST_TFD_SET(p_first_desc, queue) \ + (p_gbe_pctrl->p_tx_first_desc_q[queue] = (p_first_desc)) + +/* Macros that save access to desc in order to find next desc pointer */ +#define RX_NEXT_DESC_PTR(p_rx_desc, queue) ( \ + struct kwgbe_rx_dscr*)(((((u32)p_rx_desc - \ + (u32)p_gbe_pctrl->p_rx_desc_area_base[queue]) + \ + RX_DESC_ALIGNED_SIZE) % p_gbe_pctrl->rx_desc_area_size[queue]) + \ + (u32)p_gbe_pctrl->p_rx_desc_area_base[queue]) + +#define TX_NEXT_DESC_PTR(p_tx_desc, queue) ( \ + struct kwgbe_tx_dscr*)(((((u32)p_tx_desc - \ + (u32)p_gbe_pctrl->p_tx_desc_area_base[queue]) + \ + TX_DESC_ALIGNED_SIZE) % p_gbe_pctrl->tx_desc_area_size[queue]) + \ + (u32)p_gbe_pctrl->p_tx_desc_area_base[queue]) + +enum kwgbe_fret_sts { + KWGBE_OK, /* Returned as expected. */ + KWGBE_ERROR, /* Fundamental error. */ + KWGBE_RETRY, /* Could not process request. Try later. */ + KWGBE_END_OF_JOB, /* Ring has nothing to process. */ + KWGBE_QFULL, /* Ring resource error. */ + KWGBE_QLAST_RESO /* Ring resources about to exhaust. */ +}; + +enum kwgbe_q { + KWGBE_Q0 = 0, + KWGBE_Q1 = 1, + KWGBE_Q2 = 2, + KWGBE_Q3 = 3, + KWGBE_Q4 = 4, + KWGBE_Q5 = 5, + KWGBE_Q6 = 6, + KWGBE_Q7 = 7 +}; + +enum kwgbe_adrwin { + KWGBE_WIN0, + KWGBE_WIN1, + KWGBE_WIN2, + KWGBE_WIN3, + KWGBE_WIN4, + KWGBE_WIN5 +}; + +enum kwgbe_target { + KWGBE_TARGET_DRAM, + KWGBE_TARGET_DEV, + KWGBE_TARGET_CBS, + KWGBE_TARGET_PCI0, + KWGBE_TARGET_PCI1 +}; + +struct kwgbe_rx_dscr { + u32 cmd_sts; /* Descriptor command status */ + u16 buf_size; /* Buffer size */ + u16 byte_cnt; /* Descriptor buffer byte count */ + u32 buf_ptr; /* Descriptor buffer pointer */ + u32 nxtdesc_p; /* Next descriptor pointer */ + u32 retinfo; /* User resource return information */ +}; + +struct kwgbe_tx_dscr { + u32 cmd_sts; /* Descriptor command status */ + u16 l4i_chk; /* CPU provided TCP Checksum */ + u16 byte_cnt; /* Descriptor buffer byte count */ + u32 buf_ptr; /* Descriptor buffer pointer */ + u32 nxtdesc_p; /* Next descriptor pointer */ + u32 retinfo; /* User resource return information */ +}; + +/* + * Unified struct for Rx and Tx operations. The user is not required to + * be familier with neither Tx nor Rx descriptors. + */ +struct kwgbe_pktinf { + u32 cmd_sts; /* Descriptor command status */ + u16 byte_cnt; /* Descriptor buffer byte count */ + u16 l4i_chk; /* Tx CPU provided TCP Checksum */ + u32 buf_ptr; /* Descriptor buffer pointer */ + u32 retinfo; /* User resource return information */ +}; + +struct kwgbe_winparam { + enum kwgbe_adrwin win; /* Window number */ + enum kwgbe_target target; /* System targets */ + u16 attrib; /* BAR attrib. See above macros */ + u32 base_addr; /* Window base address in u32 form */ + u32 high_addr; /* Window high address in u32 form */ + u32 size; /* Size in MBytes. Must be % 64Kbyte. */ + int enable; /* Enable/disable access to the window. */ + u16 access_ctrl; /*Access ctrl register. see above macros */ +}; + +/* Ethernet port specific infomation */ +struct kwgbe_portinfo { + int port_phy_addr; /* User phy address of Ethrnet port */ + u8 port_mac_addr[6]; /* User defined port MAC address. */ + u32 port_config; /* User port configuration value */ + u32 port_config_extend; /* User port config extend value */ + u32 port_sdma_config; /* User port SDMA config value */ + u32 port_serial_control; /* User port serial control value */ + u32 port_tx_queue_command; /* Port active Tx queues summary */ + u32 port_rx_queue_command; /* Port active Rx queues summary */ + + /* User function to cast virtual address to CPU bus address */ + u32(*port_virt_to_phys) (u32 addr); + /* User scratch pad for user specific data structures */ + void *port_private; + + int rx_resource_err[MAX_RXQ_NO]; /* Rx ring resource err flag */ + int tx_resource_err[MAX_TXQ_NO]; /* Tx ring resource err flag */ + + /* Tx/Rx rings managment indexes fields. For driver use */ + + /* Next available Rx resource */ + volatile struct kwgbe_rx_dscr *p_rx_curr_desc_q[MAX_RXQ_NO]; + /* Returning Rx resource */ + volatile struct kwgbe_rx_dscr *p_rx_used_desc_q[MAX_RXQ_NO]; + + /* Next available Tx resource */ + volatile struct kwgbe_tx_dscr *p_tx_curr_desc_q[MAX_TXQ_NO]; + /* Returning Tx resource */ + volatile struct kwgbe_tx_dscr *p_tx_used_desc_q[MAX_TXQ_NO]; + /* An extra Tx index to support txmt of multiple buffs per packet */ + volatile struct kwgbe_tx_dscr *p_tx_first_desc_q[MAX_TXQ_NO]; + + /* Tx/Rx rings size and base variables fields. For driver use */ + + volatile struct kwgbe_rx_dscr *p_rx_desc_area_base[MAX_RXQ_NO]; + u32 rx_desc_area_size[MAX_RXQ_NO]; + char *p_rx_buffer_base[MAX_RXQ_NO]; + + volatile struct kwgbe_tx_dscr *p_tx_desc_area_base[MAX_TXQ_NO]; + u32 tx_desc_area_size[MAX_TXQ_NO]; + char *p_tx_buffer_base[MAX_TXQ_NO]; +}; + +/* port device data struct */ +struct kwgbe_device { + struct eth_device dev; + struct kwgbe_portinfo portinfo; + struct egiga_priv portpriv; + struct kwgbe_registers *regs; +}; + +/* functions */ +static void port_uc_addr_set(struct kwgbe_registers *regs, u8 * p_addr, + enum kwgbe_q queue); +static void port_reset(struct kwgbe_registers *regs); + +#endif /* __EGIGA_H__ */ diff --git a/include/netdev.h b/include/netdev.h index 4f2b23a..3f2dc83 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -52,6 +52,7 @@ int fec_initialize (bd_t *bis); int greth_initialize(bd_t *bis); void gt6426x_eth_initialize(bd_t *bis); int inca_switch_initialize(bd_t *bis); +int kirkwood_egiga_initialize(bd_t *bis); int macb_eth_initialize(int id, void *regs, unsigned int phy_addr); int mcdmafec_initialize(bd_t *bis); int mcffec_initialize(bd_t *bis);