Implement setbrg in amlogic/meson serial device with driver model similar to how the meson_uart.c driver does it in Linux. Also configure (probe) the serial device with the new reg5 register.
Signed-off-by: Edoardo Tomelleri e.tomell@gmail.com ---
drivers/serial/serial_meson.c | 70 +++++++++++++++++++++++++++++++++++ include/configs/meson64.h | 7 ++++ 2 files changed, 77 insertions(+)
diff --git a/drivers/serial/serial_meson.c b/drivers/serial/serial_meson.c index d69ec221..90c370cf 100644 --- a/drivers/serial/serial_meson.c +++ b/drivers/serial/serial_meson.c @@ -7,9 +7,11 @@ #include <dm.h> #include <errno.h> #include <fdtdec.h> +#include <linux/kernel.h> #include <linux/bitops.h> #include <linux/compiler.h> #include <serial.h> +#include <clk.h>
struct meson_uart { u32 wfifo; @@ -17,6 +19,7 @@ struct meson_uart { u32 control; u32 status; u32 misc; + u32 reg5; /* New baud control register */ };
struct meson_serial_plat { @@ -42,6 +45,35 @@ struct meson_serial_plat { #define AML_UART_RX_RST BIT(23) #define AML_UART_CLR_ERR BIT(24)
+/* AML_UART_REG5 bits */ +#define AML_UART_REG5_XTAL_DIV2 BIT(27) +#define AML_UART_REG5_XTAL_CLK_SEL BIT(26) /* default 0 (div by 3), 1 for no div */ +#define AML_UART_REG5_USE_XTAL_CLK BIT(24) /* default 1 (use crystal as clock source) */ +#define AML_UART_REG5_USE_NEW_BAUD BIT(23) /* default 1 (use new baud rate register) */ +#define AML_UART_REG5_BAUD_MASK 0x7fffff + +static u32 meson_calc_baud_divisor(ulong src_rate, u32 baud) +{ + /* + * Usually src_rate is 24 MHz (from crystal) as clock source for serial + * device. Since 8 Mb/s is the maximum supported baud rate, use div by 3 + * to derive baud rate. This choice is used also in meson_serial_setbrg. + */ + return DIV_ROUND_CLOSEST(src_rate / 3, baud) - 1; +} + +static void meson_serial_set_baud(struct meson_uart *uart, ulong src_rate, u32 baud) +{ + /* + * Set crystal divided by 3 (regardless of device tree clock property) + * as clock source and the corresponding divisor to approximate baud + */ + u32 divisor = meson_calc_baud_divisor(src_rate, baud); + u32 val = AML_UART_REG5_USE_XTAL_CLK | AML_UART_REG5_USE_NEW_BAUD | + (divisor & AML_UART_REG5_BAUD_MASK); + writel(val, &uart->reg5); +} + static void meson_serial_init(struct meson_uart *uart) { u32 val; @@ -59,7 +91,14 @@ static int meson_serial_probe(struct udevice *dev) { struct meson_serial_plat *plat = dev_get_plat(dev); struct meson_uart *const uart = plat->reg; + struct clk per_clk; + int ret = clk_get_by_name(dev, "baud", &per_clk); + + if (ret) + return ret; + ulong rate = clk_get_rate(&per_clk);
+ meson_serial_set_baud(uart, rate, CONFIG_BAUDRATE); meson_serial_init(uart);
return 0; @@ -111,6 +150,36 @@ static int meson_serial_putc(struct udevice *dev, const char ch) return 0; }
+static int meson_serial_setbrg(struct udevice *dev, const int baud) +{ + /* + * Change device baud rate if baud is reasonable (considering a 23 bit + * counter with an 8 MHz clock input) and the actual baud + * rate is within 2% of the requested value (2% is arbitrary). + */ + if (baud < 1 || baud > 8000000) + return -EINVAL; + + struct meson_serial_plat *const plat = dev_get_plat(dev); + struct meson_uart *const uart = plat->reg; + struct clk per_clk; + int ret = clk_get_by_name(dev, "baud", &per_clk); + + if (ret) + return ret; + ulong rate = clk_get_rate(&per_clk); + u32 divisor = meson_calc_baud_divisor(rate, baud); + u32 calc_baud = (rate / 3) / (divisor + 1); + u32 calc_err = baud > calc_baud ? baud - calc_baud : calc_baud - baud; + + if (((calc_err * 100) / baud) > 2) + return -EINVAL; + + meson_serial_set_baud(uart, rate, baud); + + return 0; +} + static int meson_serial_pending(struct udevice *dev, bool input) { struct meson_serial_plat *plat = dev_get_plat(dev); @@ -154,6 +223,7 @@ static const struct dm_serial_ops meson_serial_ops = { .putc = meson_serial_putc, .pending = meson_serial_pending, .getc = meson_serial_getc, + .setbrg = meson_serial_setbrg, };
static const struct udevice_id meson_serial_ids[] = { diff --git a/include/configs/meson64.h b/include/configs/meson64.h index 196e58ed..01413a02 100644 --- a/include/configs/meson64.h +++ b/include/configs/meson64.h @@ -16,6 +16,13 @@ #define GICC_BASE 0xc4302000 #endif
+/* Serial drivers */ +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, \ + 230400, 250000, 460800, 500000, 1000000, 2000000, 4000000, \ + 8000000 } + /* For splashscreen */ #ifdef CONFIG_DM_VIDEO #define STDOUT_CFG "vidconsole,serial"