This patch enables to run Universal board on device tree.
Signed-off-by: Piotr Wilczek p.wilczek@samsung.com Signed-off-by: Kyungmin Park kyungmin.park@samsung.com Cc: Minkyu Kang mk7.kang@samsung.com
Acked-by: Przemyslaw Marczak p.marczak@samsung.com --- Changes for v4: - define CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET, CONFIG_CMD_I2C at each board
Changes for v3: - dts file moved to arch/arm/dts
Changes for v2: - no changes
arch/arm/dts/Makefile | 3 +- arch/arm/dts/exynos4210-universal_c210.dts | 83 ++++++++++++ board/samsung/universal_c210/universal.c | 204 ++++++++--------------------- include/configs/s5pc210_universal.h | 152 +++++++-------------- 4 files changed, 185 insertions(+), 257 deletions(-) create mode 100644 arch/arm/dts/exynos4210-universal_c210.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 7abca75..d30954c 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1,4 +1,5 @@ -dtb-$(CONFIG_EXYNOS4) += exynos4210-origen.dtb +dtb-$(CONFIG_EXYNOS4) += exynos4210-origen.dtb \ + exynos4210-universal_c210.dtb
dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \ exynos5250-snow.dtb \ diff --git a/arch/arm/dts/exynos4210-universal_c210.dts b/arch/arm/dts/exynos4210-universal_c210.dts new file mode 100644 index 0000000..1cdd981 --- /dev/null +++ b/arch/arm/dts/exynos4210-universal_c210.dts @@ -0,0 +1,83 @@ +/* + * Samsung's Exynos4210 based Universal C210 board device tree source + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/dts-v1/; +/include/ "exynos4.dtsi" + +/ { + model = "Samsung Universal C210 based on Exynos4210 rev0"; + compatible = "samsung,universal_c210", "samsung,exynos4210"; + + aliases { + serial0 = "/serial@13800000"; + console = "/serial@13820000"; + mmc0 = "sdhci@12510000"; + mmc2 = "sdhci@12530000"; + }; + + sdhci@12510000 { + samsung,bus-width = <8>; + samsung,timing = <1 3 3>; + pwr-gpios = <&gpio 0x2008002 0>; + }; + + sdhci@12520000 { + status = "disabled"; + }; + + sdhci@12530000 { + samsung,bus-width = <4>; + samsung,timing = <1 2 3>; + cd-gpios = <&gpio 0x20c6004 0>; + }; + + sdhci@12540000 { + status = "disabled"; + }; + + fimd@11c00000 { + compatible = "samsung,exynos-fimd"; + reg = <0x11c00000 0xa4>; + + samsung,vl-freq = <60>; + samsung,vl-col = <480>; + samsung,vl-row = <800>; + samsung,vl-width = <480>; + samsung,vl-height = <800>; + + samsung,vl-clkp = <0>; + samsung,vl-oep = <0>; + samsung,vl-hsp = <1>; + samsung,vl-vsp = <1>; + samsung,vl-dp = <1>; + samsung,vl-bpix = <4>; + + samsung,vl-hspw = <2>; + samsung,vl-hbpd = <16>; + samsung,vl-hfpd = <16>; + samsung,vl-vspw = <2>; + samsung,vl-vbpd = <8>; + samsung,vl-vfpd = <8>; + samsung,vl-cmd-allow-len = <0xf>; + + samsung,pclk_name = <1>; + samsung,sclk_div = <1>; + + samsung,winid = <0>; + samsung,power-on-delay = <10000>; + samsung,interface-mode = <1>; + samsung,mipi-enabled = <0>; + samsung,dp-enabled; + samsung,dual-lcd-enabled; + + samsung,logo-on = <1>; + samsung,resolution = <0>; + samsung,rgb-mode = <0>; + }; +}; diff --git a/board/samsung/universal_c210/universal.c b/board/samsung/universal_c210/universal.c index 96da7e0..82249d3 100644 --- a/board/samsung/universal_c210/universal.c +++ b/board/samsung/universal_c210/universal.c @@ -13,16 +13,17 @@ #include <asm/gpio.h> #include <asm/arch/adc.h> #include <asm/arch/gpio.h> -#include <asm/arch/mmc.h> #include <asm/arch/pinmux.h> #include <asm/arch/watchdog.h> -#include <libtizen.h> #include <ld9040.h> #include <power/pmic.h> +#include <usb.h> #include <usb/s3c_udc.h> #include <asm/arch/cpu.h> #include <power/max8998_pmic.h> +#include <libtizen.h> #include <samsung/misc.h> +#include <usb_mass_storage.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -42,7 +43,7 @@ static int get_hwrev(void)
static void init_pmic_lcd(void);
-int power_init_board(void) +int exynos_power_init(void) { int ret;
@@ -59,22 +60,6 @@ int power_init_board(void) return 0; }
-int dram_init(void) -{ - gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + - get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE); - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - gd->bd->bi_dram[1].start = PHYS_SDRAM_2; - gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; -} - static unsigned short get_adc_value(int channel) { struct s5p_adc *adc = (struct s5p_adc *)samsung_get_base_adc(); @@ -159,71 +144,6 @@ static void check_hw_revision(void) board_rev |= hwrev; }
-#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - puts("Board:\tUniversal C210\n"); - return 0; -} -#endif - -#ifdef CONFIG_GENERIC_MMC -int board_mmc_init(bd_t *bis) -{ - int err; - - switch (get_hwrev()) { - case 0: - /* - * Set the low to enable LDO_EN - * But when you use the test board for eMMC booting - * you should set it HIGH since it removes the inverter - */ - /* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */ - s5p_gpio_direction_output(&gpio1->e3, 6, 0); - break; - default: - /* - * Default reset state is High and there's no inverter - * But set it as HIGH to ensure - */ - /* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */ - s5p_gpio_direction_output(&gpio1->e1, 3, 1); - break; - } - - /* - * MMC device init - * mmc0 : eMMC (8-bit buswidth) - * mmc2 : SD card (4-bit buswidth) - */ - err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - if (err) - debug("SDMMC0 not configured\n"); - else - err = s5p_mmc_init(0, 8); - - /* T-flash detect */ - s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf); - s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP); - - /* - * Check the T-flash detect pin - * GPX3[4] T-flash detect pin - */ - if (!s5p_gpio_get_value(&gpio2->x3, 4)) { - err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); - if (err) - debug("SDMMC2 not configured\n"); - else - err = s5p_mmc_init(2, 4); - } - - return err; - -} -#endif - #ifdef CONFIG_USB_GADGET static int s5pc210_phy_control(int on) { @@ -271,7 +191,20 @@ struct s3c_plat_otg_data s5pc210_otg_data = { }; #endif
-int board_early_init_f(void) +int board_usb_init(int index, enum usb_init_type init) +{ + debug("USB_udc_probe\n"); + return s3c_udc_probe(&s5pc210_otg_data); +} + +#ifdef CONFIG_USB_CABLE_CHECK +int usb_cable_connected(void) +{ + return 0; +} +#endif + +int exynos_early_init_f(void) { wdt_stop();
@@ -412,6 +345,11 @@ void exynos_cfg_lcd_gpio(void) spi_init(); }
+int mipi_power(void) +{ + return 0; +} + void exynos_reset_lcd(void) { s5p_gpio_set_value(&gpio2->y4, 5, 1); @@ -436,39 +374,6 @@ void exynos_lcd_power_on(void) pmic_set_output(p, MAX8998_REG_ONOFF2, MAX8998_LDO7, LDO_ON); }
-vidinfo_t panel_info = { - .vl_freq = 60, - .vl_col = 480, - .vl_row = 800, - .vl_width = 480, - .vl_height = 800, - .vl_clkp = CONFIG_SYS_HIGH, - .vl_hsp = CONFIG_SYS_HIGH, - .vl_vsp = CONFIG_SYS_HIGH, - .vl_dp = CONFIG_SYS_HIGH, - - .vl_bpix = 4, /* Bits per pixel */ - - /* LD9040 LCD Panel */ - .vl_hspw = 2, - .vl_hbpd = 16, - .vl_hfpd = 16, - - .vl_vspw = 2, - .vl_vbpd = 8, - .vl_vfpd = 8, - .vl_cmd_allow_len = 0xf, - - .win_id = 0, - .dual_lcd_enabled = 0, - - .init_delay = 0, - .power_on_delay = 10000, - .reset_delay = 10000, - .interface_mode = FIMD_RGB_INTERFACE, - .mipi_enabled = 0, -}; - void exynos_cfg_ldo(void) { ld9040_cfg_ldo(); @@ -479,30 +384,32 @@ void exynos_enable_ldo(unsigned int onoff) ld9040_enable_ldo(onoff); }
-void init_panel_info(vidinfo_t *vid) -{ - vid->logo_on = 1; - vid->resolution = HD_RESOLUTION; - vid->rgb_mode = MODE_RGB_P; - -#ifdef CONFIG_TIZEN - get_tizen_logo_info(vid); -#endif - - /* for LD9040. */ - vid->pclk_name = 1; /* MPLL */ - vid->sclk_div = 1; - - setenv("lcdinfo", "lcd=ld9040"); -} - -int board_init(void) +int exynos_init(void) { gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE; gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE;
gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210; - gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + + switch (get_hwrev()) { + case 0: + /* + * Set the low to enable LDO_EN + * But when you use the test board for eMMC booting + * you should set it HIGH since it removes the inverter + */ + /* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */ + s5p_gpio_direction_output(&gpio1->e3, 6, 0); + break; + default: + /* + * Default reset state is High and there's no inverter + * But set it as HIGH to ensure + */ + /* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */ + s5p_gpio_direction_output(&gpio1->e1, 3, 1); + break; + }
#ifdef CONFIG_SOFT_SPI soft_spi_init(); @@ -513,20 +420,15 @@ int board_init(void) return 0; }
-#ifdef CONFIG_MISC_INIT_R -int misc_init_r(void) +void exynos_lcd_panel_init(vidinfo_t *vid) { -#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG - set_board_info(); -#endif -#ifdef CONFIG_LCD_MENU - keys_init(); - check_boot_mode(); -#endif -#ifdef CONFIG_CMD_BMP - if (panel_info.logo_on) - draw_logo(); +#ifdef CONFIG_TIZEN + get_tizen_logo_info(vid); #endif - return 0; + + /* for LD9040. */ + vid->pclk_name = 1; /* MPLL */ + vid->sclk_div = 1; + + setenv("lcdinfo", "lcd=ld9040"); } -#endif diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index 67921e9..2da8871 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -7,78 +7,56 @@ * SPDX-License-Identifier: GPL-2.0+ */
-#ifndef __CONFIG_H -#define __CONFIG_H +#ifndef __CONFIG_UNIVERSAL_H +#define __CONFIG_UNIVERSAL_H
-/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ -#define CONFIG_S5P 1 /* which is in a S5P Family */ -#define CONFIG_EXYNOS4210 1 /* which is in a EXYNOS4210 */ -#define CONFIG_UNIVERSAL 1 /* working with Universal */ -#define CONFIG_TIZEN 1 /* TIZEN lib */ +#include <configs/exynos4-dt.h> + +#define CONFIG_SYS_PROMPT "Universal # " /* Monitor Command Prompt */
-#include <asm/arch/cpu.h> /* get chip and board defs */ +#undef CONFIG_DEFAULT_DEVICE_TREE +#define CONFIG_DEFAULT_DEVICE_TREE exynos4210-universal_c210
-#define CONFIG_ARCH_CPU_INIT -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_TIZEN /* TIZEN lib */
/* Keep L2 Cache Disabled */ #define CONFIG_SYS_L2CACHE_OFF 1
+/* Universal has 2 banks of DRAM */ +#define CONFIG_NR_DRAM_BANKS 2 #define CONFIG_SYS_SDRAM_BASE 0x40000000 -#define CONFIG_SYS_TEXT_BASE 0x44800000 - -/* input clock of PLL: Universal has 24MHz input clock at EXYNOS4210 */ -#define CONFIG_SYS_CLK_FREQ_C210 24000000 -#define CONFIG_SYS_CLK_FREQ CONFIG_SYS_CLK_FREQ_C210 +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_CMDLINE_TAG -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG -#define CONFIG_CMDLINE_EDITING -#define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_BOARD_EARLY_INIT_F +#define SDRAM_BANK_SIZE (256 << 20) /* 256 MB */
/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20)) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (80 * SZ_1M))
/* select serial console configuration */ -#define CONFIG_SERIAL2 1 /* use SERIAL 2 */ -#define CONFIG_BAUDRATE 115200 - -/* MMC */ -#define CONFIG_GENERIC_MMC -#define CONFIG_MMC -#define CONFIG_SDHCI -#define CONFIG_S5P_SDHCI - -/* PWM */ -#define CONFIG_PWM 1 - -/* It should define before config_cmd_default.h */ -#define CONFIG_SYS_NO_FLASH 1 - -/* Command definition */ -#include <config_cmd_default.h> - -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_MISC -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_XIMG -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_ONENAND -#define CONFIG_CMD_MTDPARTS -#define CONFIG_CMD_MMC -#define CONFIG_CMD_FAT - -#define CONFIG_BOOTDELAY 1 -#define CONFIG_ZERO_BOOTDELAY_CHECK +#define CONFIG_SERIAL2 +#define CONFIG_BAUDRATE 115200 + +/* Console configuration */ +#define CONFIG_SYS_CONSOLE_INFO_QUIET +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +#define CONFIG_BOOTARGS "Please use defined boot" +#define CONFIG_BOOTCOMMAND "run mmcboot" +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \ + - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_MEM_TOP_HIDE (1 << 20) /* ram console */ + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 + +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5000000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x4800000) + +#define CONFIG_SYS_TEXT_BASE 0x44800000
#define CONFIG_MTD_DEVICE #define CONFIG_MTD_PARTITIONS @@ -106,24 +84,21 @@ ",100M(swap)"\ ",-(UMS)\0"
-#define CONFIG_BOOTARGS "Please use defined boot" -#define CONFIG_BOOTCOMMAND "run mmcboot" -#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" - #define CONFIG_ENV_UBI_MTD " ubi.mtd=${ubiblock} ubi.mtd=4 ubi.mtd=7" #define CONFIG_BOOTBLOCK "10" #define CONFIG_UBIBLOCK "9"
+#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV CONFIG_MMC_DEFAULT_DEV +#define CONFIG_ENV_SIZE 4096 +#define CONFIG_ENV_OFFSET ((32 - 4) << 10) /* 32KiB - 4KiB */ + #define CONFIG_ENV_UBIFS_OPTION " rootflags=bulk_read,no_chk_data_crc " #define CONFIG_ENV_FLASHBOOT CONFIG_ENV_UBI_MTD CONFIG_ENV_UBIFS_OPTION \ "${mtdparts}"
#define CONFIG_ENV_COMMON_BOOT "${console} ${meminfo}"
-#define CONFIG_ENV_OVERWRITE -#define CONFIG_SYS_CONSOLE_INFO_QUIET -#define CONFIG_SYS_CONSOLE_IS_IN_ENV - #define CONFIG_ENV_VARS_UBOOT_CONFIG #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
@@ -187,47 +162,10 @@ "mmcrootpart=3\0" \ "opts=always_resume=1"
-/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#define CONFIG_SYS_PROMPT "Universal # " -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE -/* memtest works on */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5000000) -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x4800000) - -/* Universal has 2 banks of DRAM */ -#define CONFIG_NR_DRAM_BANKS 2 -#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE /* LDDDR2 DMC 0 */ -#define PHYS_SDRAM_1_SIZE (256 << 20) /* 256 MB in CS 0 */ -#define PHYS_SDRAM_2 0x50000000 /* LPDDR2 DMC 1 */ -#define PHYS_SDRAM_2_SIZE (256 << 20) /* 256 MB in CS 0 */ - -#define CONFIG_SYS_MEM_TOP_HIDE (1 << 20) /* ram console */ - -#define CONFIG_SYS_MONITOR_BASE 0x00000000 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - #define CONFIG_USE_ONENAND_BOARD_INIT #define CONFIG_SAMSUNG_ONENAND #define CONFIG_SYS_ONENAND_BASE 0x0C000000
-#define CONFIG_ENV_IS_IN_MMC 1 -#define CONFIG_SYS_MMC_ENV_DEV 0 -#define CONFIG_ENV_SIZE 4096 -#define CONFIG_ENV_OFFSET ((32 - 4) << 10)/* 32KiB - 4KiB */ - -#define CONFIG_DOS_PARTITION 1 - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE) - -#define CONFIG_SYS_CACHELINE_SIZE 32 - #include <asm/arch/gpio.h> /* * I2C Settings @@ -235,6 +173,8 @@ #define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_get(1, b, 7) #define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_get(1, b, 6)
+#define CONFIG_CMD_I2C + #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SYS_I2C_SOFT_SPEED 50000 @@ -307,8 +247,10 @@ int universal_spi_read(void); #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP #define CONFIG_LD9040 -#define CONFIG_EXYNOS_MIPI_DSIM #define CONFIG_VIDEO_BMP_GZIP #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 160 * 4) + 54)
+#define LCD_XRES 480 +#define LCD_YRES 800 + #endif /* __CONFIG_H */