From: Ye Li ye.li@nxp.com
The i.MX8 has two USB controllers: USBOH and USB3. The USBOH reuses previous i.MX6/7. It has same PHY IP as i.MX7ULP but NC registers are same as i.MX7D. So add its support in ehci-mx6 driver.
Also the driver is updated to remove build warning for 64 bits CPU.
Signed-off-by: Ye Li ye.li@nxp.com Signed-off-by: Peng Fan peng.fan@nxp.com --- drivers/usb/host/Kconfig | 4 +- drivers/usb/host/ehci-mx6.c | 97 ++++++++++++++++++++++++++++++++++++++------- 2 files changed, 85 insertions(+), 16 deletions(-)
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 1c374a7bd8..f48547caa0 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -139,8 +139,8 @@ config USB_EHCI_MX5 Enables support for the on-chip EHCI controller on i.MX5 SoCs.
config USB_EHCI_MX6 - bool "Support for i.MX6/i.MX7ULP on-chip EHCI USB controller" - depends on ARCH_MX6 || ARCH_MX7ULP + bool "Support for i.MX6/i.MX7ULP/i.MX8 on-chip EHCI USB controller" + depends on ARCH_MX6 || ARCH_MX7ULP || ARCH_IMX8 default y ---help--- Enables support for the on-chip EHCI controller on i.MX6 SoCs. diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c index e654595683..191d619220 100644 --- a/drivers/usb/host/ehci-mx6.c +++ b/drivers/usb/host/ehci-mx6.c @@ -62,12 +62,20 @@ DECLARE_GLOBAL_DATA_PTR; #define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */ #define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */
+#define PLL_USB_EN_USB_CLKS_MASK (0x01 << 6) +#define PLL_USB_PWR_MASK (0x01 << 12) +#define PLL_USB_ENABLE_MASK (0x01 << 13) +#define PLL_USB_BYPASS_MASK (0x01 << 16) +#define PLL_USB_REG_ENABLE_MASK (0x01 << 21) +#define PLL_USB_DIV_SEL_MASK (0x07 << 22) +#define PLL_USB_LOCK_MASK (0x01 << 31) + /* USBCMD */ #define UCMD_RUN_STOP (1 << 0) /* controller run/stop */ #define UCMD_RESET (1 << 1) /* controller reset */
-#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP) -static const unsigned phy_bases[] = { +#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP) || defined(CONFIG_IMX8) +static const ulong phy_bases[] = { USB_PHY0_BASE_ADDR, #if defined(USB_PHY1_BASE_ADDR) USB_PHY1_BASE_ADDR, @@ -101,6 +109,53 @@ static void usb_power_config(int index)
scg_enable_usb_pll(true);
+#elif defined(CONFIG_IMX8) + struct usbphy_regs __iomem *usbphy = + (struct usbphy_regs __iomem *)USB_PHY0_BASE_ADDR; + int timeout = 1000000; + + if (index > 0) + return; + + writel(ANADIG_USB2_CHRG_DETECT_EN_B | + ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B, + &usbphy->usb1_chrg_detect); + + if (!(readl(&usbphy->usb1_pll_480_ctrl) & PLL_USB_LOCK_MASK)) { + + /* Enable the regulator first */ + writel(PLL_USB_REG_ENABLE_MASK, + &usbphy->usb1_pll_480_ctrl_set); + + /* Wait at least 25us */ + udelay(25); + + /* Enable the power */ + writel(PLL_USB_PWR_MASK, &usbphy->usb1_pll_480_ctrl_set); + + /* Wait lock */ + while (timeout--) { + if (readl(&usbphy->usb1_pll_480_ctrl) & + PLL_USB_LOCK_MASK) + break; + udelay(10); + } + + if (timeout <= 0) { + /* If timeout, we power down the pll */ + writel(PLL_USB_PWR_MASK, + &usbphy->usb1_pll_480_ctrl_clr); + return; + } + } + + /* Clear the bypass */ + writel(PLL_USB_BYPASS_MASK, &usbphy->usb1_pll_480_ctrl_clr); + + /* Enable the PLL clock out to USB */ + writel((PLL_USB_EN_USB_CLKS_MASK | PLL_USB_ENABLE_MASK), + &usbphy->usb1_pll_480_ctrl_set); + #else struct anatop_regs __iomem *anatop = (struct anatop_regs __iomem *)ANATOP_BASE_ADDR; @@ -212,6 +267,20 @@ struct usbnc_regs { u32 reserve0[2]; u32 hsic_ctrl; }; +#elif defined(CONFIG_IMX8) +struct usbnc_regs { + u32 ctrl1; + u32 ctrl2; + u32 reserve1[10]; + u32 phy_cfg1; + u32 phy_cfg2; + u32 reserve2; + u32 phy_status; + u32 reserve3[4]; + u32 adp_cfg1; + u32 adp_cfg2; + u32 adp_status; +}; #else /* Base address for this IP block is 0x02184800 */ struct usbnc_regs { @@ -240,7 +309,7 @@ struct usbnc_regs {
static void usb_power_config(int index) { - struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + + struct usbnc_regs *usbnc = (struct usbnc_regs *)(ulong)(USB_BASE_ADDR + (0x10000 * index) + USBNC_OFFSET); void __iomem *phy_cfg2 = (void __iomem *)(&usbnc->phy_cfg2);
@@ -253,7 +322,7 @@ static void usb_power_config(int index)
int usb_phy_mode(int port) { - struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + + struct usbnc_regs *usbnc = (struct usbnc_regs *)(ulong)(USB_BASE_ADDR + (0x10000 * port) + USBNC_OFFSET); void __iomem *status = (void __iomem *)(&usbnc->phy_status); u32 val; @@ -292,8 +361,8 @@ static void usb_oc_config(int index) struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET); void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]); -#elif defined(CONFIG_MX7) || defined(CONFIG_MX7ULP) - struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + +#elif defined(CONFIG_MX7) || defined(CONFIG_MX7ULP) || defined(CONFIG_IMX8) + struct usbnc_regs *usbnc = (struct usbnc_regs *)(ulong)(USB_BASE_ADDR + (0x10000 * index) + USBNC_OFFSET); void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1); #endif @@ -376,7 +445,7 @@ int ehci_mx6_common_init(struct usb_ehci *ehci, int index) usb_power_config(index); usb_oc_config(index);
-#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP) +#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP) || defined(CONFIG_IMX8) usb_internal_phy_clock_gate(index, 1); usb_phy_enable(index, ehci); #endif @@ -395,10 +464,10 @@ int ehci_hcd_init(int index, enum usb_init_type init, enum usb_init_type type; #if defined(CONFIG_MX6) u32 controller_spacing = 0x200; -#elif defined(CONFIG_MX7) || defined(CONFIG_MX7ULP) +#elif defined(CONFIG_MX7) || defined(CONFIG_MX7ULP) || defined(CONFIG_IMX8) u32 controller_spacing = 0x10000; #endif - struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR + + struct usb_ehci *ehci = (struct usb_ehci *)(ulong)(USB_BASE_ADDR + (controller_spacing * index)); int ret;
@@ -422,8 +491,8 @@ int ehci_hcd_init(int index, enum usb_init_type init, type = board_usb_phy_mode(index);
if (hccr && hcor) { - *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); - *hcor = (struct ehci_hcor *)((uint32_t)*hccr + + *hccr = (struct ehci_hccr *)((ulong)&ehci->caplength); + *hcor = (struct ehci_hcor *)((ulong)*hccr + HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); }
@@ -509,7 +578,7 @@ static int ehci_usb_phy_mode(struct udevice *dev) * About fsl,usbphy, Refer to * Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt. */ - if (is_mx6() || is_mx7ulp()) { + if (is_mx6() || is_mx7ulp() || is_imx8()) { phy_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbphy"); @@ -655,8 +724,8 @@ static int ehci_usb_probe(struct udevice *dev)
mdelay(10);
- hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); - hcor = (struct ehci_hcor *)((uint32_t)hccr + + hccr = (struct ehci_hccr *)((ulong)&ehci->caplength); + hcor = (struct ehci_hcor *)((ulong)hccr + HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
return ehci_register(dev, hccr, hcor, &mx6_ehci_ops, 0, priv->init_type);