Use the full driver model GPIO and serial drivers in SPL now that these are supported. Since device tree is not available they will use platform data.
Remove the special SPL GPIO function as it is no longer needed.
This is all in one commit to maintain bisectability.
Signed-off-by: Simon Glass sjg@chromium.org ---
Changes in v6: None Changes in v5: None Changes in v4: - Rebase on top of dm/master
Changes in v3: - Drop extra blank line
Changes in v2: - Rebase on top of the SPI series
arch/arm/mach-tegra/Kconfig | 3 +++ board/nvidia/seaboard/seaboard.c | 4 +--- drivers/gpio/Makefile | 4 ++++ drivers/gpio/tegra_gpio.c | 27 +++++++++++---------------- include/configs/tegra-common.h | 6 ------ 5 files changed, 19 insertions(+), 25 deletions(-)
diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig index 8615248..fccfd79 100644 --- a/arch/arm/mach-tegra/Kconfig +++ b/arch/arm/mach-tegra/Kconfig @@ -29,6 +29,9 @@ config USE_PRIVATE_LIBGCC config DM default y
+config SPL_DM + default y + config DM_SERIAL default y
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c index 11472eb..25480e4 100644 --- a/board/nvidia/seaboard/seaboard.c +++ b/board/nvidia/seaboard/seaboard.c @@ -20,10 +20,8 @@ void gpio_early_init_uart(void) { /* Enable UART via GPIO_PI3 (port 8, bit 3) so serial console works */ -#ifndef CONFIG_SPL_BUILD gpio_request(GPIO_PI3, NULL); -#endif - tegra_spl_gpio_direction_output(GPIO_PI3, 0); + gpio_direction_output(GPIO_PI3, 0); } #endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index aa11f15..fe9a3b2 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -8,6 +8,10 @@ ifndef CONFIG_SPL_BUILD obj-$(CONFIG_DM_GPIO) += gpio-uclass.o endif +/* TODO(sjg@chromium.org): Only tegra supports driver model in SPL */ +ifdef CONFIG_TEGRA_GPIO +obj-$(CONFIG_DM_GPIO) += gpio-uclass.o +endif
obj-$(CONFIG_AT91_GPIO) += at91_gpio.o obj-$(CONFIG_INTEL_ICH6_GPIO) += intel_ich6_gpio.o diff --git a/drivers/gpio/tegra_gpio.c b/drivers/gpio/tegra_gpio.c index 43928b8..f870cdb 100644 --- a/drivers/gpio/tegra_gpio.c +++ b/drivers/gpio/tegra_gpio.c @@ -132,21 +132,6 @@ static void set_level(unsigned gpio, int high) writel(u, &bank->gpio_out[GPIO_PORT(gpio)]); }
-/* set GPIO pin 'gpio' as an output, with polarity 'value' */ -int tegra_spl_gpio_direction_output(int gpio, int value) -{ - /* Configure as a GPIO */ - set_config(gpio, 1); - - /* Configure GPIO output value. */ - set_level(gpio, value); - - /* Configure GPIO direction as output. */ - set_direction(gpio, 1); - - return 0; -} - /* * Generic_GPIO primitives. */ @@ -338,12 +323,19 @@ static int gpio_tegra_bind(struct udevice *parent) int bank_count; int bank; int ret; - int len;
/* If this is a child device, there is nothing to do here */ if (plat) return 0;
+ /* TODO(sjg@chromium.org): Remove once SPL supports device tree */ +#ifdef CONFIG_SPL_BUILD + ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; + bank_count = TEGRA_GPIO_BANKS; +#else + { + int len; + /* * This driver does not make use of interrupts, other than to figure * out the number of GPIO banks @@ -353,6 +345,8 @@ static int gpio_tegra_bind(struct udevice *parent) bank_count = len / 3 / sizeof(u32); ctlr = (struct gpio_ctlr *)fdtdec_get_addr(gd->fdt_blob, parent->of_offset, "reg"); + } +#endif for (bank = 0; bank < bank_count; bank++) { int port;
@@ -388,4 +382,5 @@ U_BOOT_DRIVER(gpio_tegra) = { .probe = gpio_tegra_probe, .priv_auto_alloc_size = sizeof(struct tegra_port_info), .ops = &gpio_tegra_ops, + .flags = DM_FLAG_PRE_RELOC, }; diff --git a/include/configs/tegra-common.h b/include/configs/tegra-common.h index 005fc6a..fa6ccc1 100644 --- a/include/configs/tegra-common.h +++ b/include/configs/tegra-common.h @@ -43,13 +43,7 @@ /* * NS16550 Configuration */ -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK -#else #define CONFIG_TEGRA_SERIAL -#endif #define CONFIG_SYS_NS16550
/*