Signed-off-by: Joe Hershberger joe.hershberger@ni.com Cc: Joe Hershberger joe.hershberger@gmail.com Cc: Kim Phillips kim.phillips@freescale.com --- include/configs/sbc8349.h | 236 +++++++++++++++++++++++++++------------------ 1 files changed, 143 insertions(+), 93 deletions(-)
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index b418cf2..d6207dd 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -71,7 +71,7 @@
#define CONFIG_SYS_IMMR 0xE0000000
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ #define CONFIG_SYS_MEMTEST_END 0x00100000
@@ -81,7 +81,7 @@ #undef CONFIG_DDR_ECC /* only for ECC DDR module */ #undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ -#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */ +#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */
/* * 32-bit data path mode. @@ -95,7 +95,7 @@ */ #undef CONFIG_DDR_32BIT
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ @@ -114,18 +114,22 @@ * NB: manual DDR setup untested on sbc834x */ #define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) +#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ROW_BIT_13 \ + | CSCONFIG_COL_BIT_10) #define CONFIG_SYS_DDR_TIMING_1 0x36332321 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ +#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ #define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */
#if defined(CONFIG_DDR_32BIT) /* set burst length to 8 for 32-bit data path */ -#define CONFIG_SYS_DDR_MODE 0x00000023 /* DLL,normal,seq,4/2.5, 8 burst len */ + /* DLL,normal,seq,4/2.5, 8 burst len */ +#define CONFIG_SYS_DDR_MODE 0x00000023 #else /* the default burst length is 4 - for 64-bit data path */ -#define CONFIG_SYS_DDR_MODE 0x00000022 /* DLL,normal,seq,4/2.5, 4 burst len */ + /* DLL,normal,seq,4/2.5, 4 burst len */ +#define CONFIG_SYS_DDR_MODE 0x00000022 #endif #endif
@@ -133,27 +137,28 @@ * SDRAM on the Local Bus */ #define CONFIG_SYS_LBC_SDRAM_BASE 0x10000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */
/* * FLASH on the Local Bus */ -#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ #define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */ #define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */ /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* flash Base address */ \ - (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ - BR_V) /* valid */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ + | (2 << BR_PS_SHIFT) /* 16 bit port */ \ + | BR_V) /* valid */
#define CONFIG_SYS_OR0_PRELIM 0xFF806FF7 /* 8 MB flash size */ -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* window base at flash base */ + /* window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */
#undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ @@ -168,14 +173,17 @@ #endif
#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ + /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 + /* Size of used area in RAM*/ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* * Local Bus LCRR and LBCR regs @@ -209,7 +217,8 @@ * FIXME: the top 17 bits of BR2. */
-#define CONFIG_SYS_BR2_PRELIM 0xF0001861 /* Port-size=32bit, MSEL=SDRAM */ + /* Port-size=32bit, MSEL=SDRAM */ +#define CONFIG_SYS_BR2_PRELIM 0xF0001861 #define CONFIG_SYS_LBLAWBAR2_PRELIM 0xF0000000 #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* 64M */
@@ -229,18 +238,19 @@
#define CONFIG_SYS_OR2_PRELIM 0xFC006901
-#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ + /* LB sdram refresh timer, about 6us */ +#define CONFIG_SYS_LBC_LSRT 0x32000000 + /* LB refresh timer prescal, 266MHz/32 */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000
-#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFEN \ - | LSDMR_BSMA1516 \ - | LSDMR_RFCR8 \ - | LSDMR_PRETOACT6 \ - | LSDMR_ACTTORW3 \ - | LSDMR_BL8 \ - | LSDMR_WRC3 \ - | LSDMR_CL3 \ - ) +#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \ + | LSDMR_BSMA1516 \ + | LSDMR_RFCR8 \ + | LSDMR_PRETOACT6 \ + | LSDMR_ACTTORW3 \ + | LSDMR_BL8 \ + | LSDMR_WRC3 \ + | LSDMR_CL3)
/* * SDRAM Controller configuration sequence. @@ -262,7 +272,7 @@ #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) @@ -271,7 +281,7 @@ #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER -#ifdef CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif
@@ -284,19 +294,19 @@ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C1_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET +#define CONFIG_SYS_I2C1_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
/* TSEC */ #define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) #define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
/* * General PCI @@ -308,9 +318,9 @@ #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 #define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE @@ -318,9 +328,9 @@ #define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 #define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE #define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 -#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 +#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
@@ -390,7 +400,7 @@ #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#else - #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ + #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 @@ -438,22 +448,25 @@ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + /* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/* * For booting Linux, the board info and command line data * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ + /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
@@ -506,7 +519,7 @@ HRCWH_SW_WATCHDOG_DISABLE |\ HRCWH_ROM_LOC_LOCAL_16BIT |\ HRCWH_TSEC1M_IN_GMII |\ - HRCWH_TSEC2M_IN_GMII ) + HRCWH_TSEC2M_IN_GMII) #else #define CONFIG_SYS_HRCW_HIGH (\ HRCWH_PCI_HOST |\ @@ -519,7 +532,7 @@ HRCWH_SW_WATCHDOG_DISABLE |\ HRCWH_ROM_LOC_LOCAL_16BIT |\ HRCWH_TSEC1M_IN_GMII |\ - HRCWH_TSEC2M_IN_GMII ) + HRCWH_TSEC2M_IN_GMII) #endif
/* System IO Config */ @@ -527,13 +540,13 @@ #define CONFIG_SYS_SICRL SICRL_LDP_A
#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE) +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \ + | HID0_ENABLE_INSTRUCTION_CACHE)
-/* #define CONFIG_SYS_HID0_FINAL (\ +/* #define CONFIG_SYS_HID0_FINAL (\ HID0_ENABLE_INSTRUCTION_CACHE |\ HID0_ENABLE_M_BIT |\ - HID0_ENABLE_ADDRESS_BROADCAST ) */ + HID0_ENABLE_ADDRESS_BROADCAST) */
#define CONFIG_SYS_HID2 HID2_HBE @@ -541,15 +554,31 @@ #define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR @ 0x00000000 */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ + | BATL_PP_10 \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP)
/* PCI @ 0x80000000 */ #ifdef CONFIG_PCI -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \ + | BATL_PP_10 \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATL_PP_10 \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) #else #define CONFIG_SYS_IBAT1L (0) #define CONFIG_SYS_IBAT1U (0) @@ -558,10 +587,21 @@ #endif
#ifdef CONFIG_MPC83XX_PCI2 -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \ + | BATL_PP_10 \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \ + | BATL_PP_10 \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) #else #define CONFIG_SYS_IBAT3L (0) #define CONFIG_SYS_IBAT3U (0) @@ -570,12 +610,20 @@ #endif
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */ -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ + | BATL_PP_10 \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ -#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \ - BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT6L (0xF0000000 \ + | BATL_PP_10 \ + | BATL_MEMCOHERENCE \ + | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L (0) @@ -617,10 +665,11 @@ #define CONFIG_ROOTPATH /tftpboot/rootfs #define CONFIG_BOOTFILE uImage
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + /* default location for tftp and bootm */ +#define CONFIG_LOADADDR 800000
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
@@ -642,28 +691,29 @@ "bootm\0" \ "load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0" \ "update=protect off ff800000 ff83ffff; " \ - "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \ + "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \ "upd=run load update\0" \ "fdtaddr=780000\0" \ "fdtfile=sbc8349.dtb\0" \ ""
-#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ + "$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND "run flash_self"