Hi,
On Tue, Jan 10, 2017 at 05:18:22PM +0800, Icenowy Zheng wrote:
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is disabled in this version.
Signed-off-by: Icenowy Zheng icenowy@aosc.xyz
arch/arm/include/asm/arch-sunxi/gpio.h | 1 + arch/arm/mach-sunxi/board.c | 9 ++++++-- arch/arm/mach-sunxi/cpu_info.c | 2 ++ board/sunxi/Kconfig | 12 ++++++++-- include/configs/sun8i.h | 2 ++ include/configs/sunxi-common.h | 42 +++++++++++++++++++++++++++++++--- 6 files changed, 61 insertions(+), 7 deletions(-)
diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h index 85a4ec3b0e..24f85206c8 100644 --- a/arch/arm/include/asm/arch-sunxi/gpio.h +++ b/arch/arm/include/asm/arch-sunxi/gpio.h @@ -161,6 +161,7 @@ enum sunxi_gpio_number { #define SUN8I_GPB_UART2 2 #define SUN8I_A33_GPB_UART0 3 #define SUN8I_A83T_GPB_UART0 2 +#define SUN8I_V3S_GPB_UART0 3 #define SUN50I_GPB_UART0 4
#define SUNXI_GPC_NAND 2 diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c index aa11493748..3b28478e2d 100644 --- a/arch/arm/mach-sunxi/board.c +++ b/arch/arm/mach-sunxi/board.c @@ -110,6 +110,10 @@ static int gpio_init(void) sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_A83T_GPB_UART0); sunxi_gpio_set_cfgpin(SUNXI_GPB(10), SUN8I_A83T_GPB_UART0); sunxi_gpio_set_pull(SUNXI_GPB(10), SUNXI_GPIO_PULL_UP); +#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_V3S)
- sunxi_gpio_set_cfgpin(SUNXI_GPB(8), SUN8I_V3S_GPB_UART0);
- sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_V3S_GPB_UART0);
- sunxi_gpio_set_pull(SUNXI_GPB(9), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I) sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0); sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0); @@ -180,10 +184,11 @@ void s_init(void) /* No H3 BSP, boot0 seems to not modify SUNXI_SRAMC_BASE + 0x44 */ #endif
-#if defined CONFIG_MACH_SUN6I || \ +#if (defined CONFIG_MACH_SUN6I || \ defined CONFIG_MACH_SUN7I || \ defined CONFIG_MACH_SUN8I || \
- defined CONFIG_MACH_SUN9I
- defined CONFIG_MACH_SUN9I) && \
- !defined CONFIG_MACH_SUN8I_V3S /* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */ asm volatile( "mrc p15, 0, r0, c1, c0, 1\n"
diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c index f1f6fd5ba4..15f1e0e45a 100644 --- a/arch/arm/mach-sunxi/cpu_info.c +++ b/arch/arm/mach-sunxi/cpu_info.c @@ -87,6 +87,8 @@ int print_cpuinfo(void) printf("CPU: Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id()); #elif defined CONFIG_MACH_SUN8I_H3 printf("CPU: Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id()); +#elif defined CONFIG_MACH_SUN8I_V3S
- printf("CPU: Allwinner V3s (SUN8I %04x)\n", sunxi_get_sram_id());
#elif defined CONFIG_MACH_SUN9I puts("CPU: Allwinner A80 (SUN9I)\n"); #elif defined CONFIG_MACH_SUN50I diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index e1d4ab148f..1eb23c3a4c 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -115,6 +115,14 @@ config MACH_SUN8I_H3 select SUPPORT_SPL select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+config MACH_SUN8I_V3S
- bool "sun8i (Allwinner V3s)"
- select CPU_V7
- select CPU_V7_HAS_NONSEC
- select CPU_V7_HAS_VIRT
- select SUNXI_GEN_SUN6I
- select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN9I bool "sun9i (Allwinner A80)" select CPU_V7 @@ -131,7 +139,7 @@ endchoice # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" config MACH_SUN8I bool
- default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_H3 || MACH_SUN8I_A83T
- default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_H3 || MACH_SUN8I_A83T || MACH_SUN8I_V3S
This needs some wrapping
config DRAM_TYPE int "sunxi dram type" @@ -462,7 +470,7 @@ config AXP_GPIO
config VIDEO bool "Enable graphical uboot console on HDMI, LCD or VGA"
- depends on !MACH_SUN8I_A83T && !MACH_SUN8I_H3 && !MACH_SUN9I && !MACH_SUN50I
- depends on !MACH_SUN8I_A83T && !MACH_SUN8I_H3 && !MACH_SUN8I_V3S && !MACH_SUN9I && !MACH_SUN50I
Ditto.
default y ---help--- Say Y here to add support for using a cfb console on the HDMI, LCD diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h index a4c3fb69e4..6ac42acaea 100644 --- a/include/configs/sun8i.h +++ b/include/configs/sun8i.h @@ -21,6 +21,8 @@ #define CONFIG_SUNXI_USB_PHYS 4 #elif defined CONFIG_MACH_SUN8I_A83T #define CONFIG_SUNXI_USB_PHYS 3 +#elif defined CONFIG_MACH_SUN8I_V3S
- #define CONFIG_SUNXI_USB_PHYS 1
#else #define CONFIG_SUNXI_USB_PHYS 2 #endif diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h index b0bfc0dfd7..f4489fad6d 100644 --- a/include/configs/sunxi-common.h +++ b/include/configs/sunxi-common.h @@ -75,8 +75,13 @@ #else #define SDRAM_OFFSET(x) 0x4##x #define CONFIG_SYS_SDRAM_BASE 0x40000000 -#define CONFIG_SYS_LOAD_ADDR 0x42000000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x41000000 /* default load address */ +/* V3s do not have enough memory to place code at 0x4a000000 */ +#ifndef CONFIG_MACH_SUN8I_V3S #define CONFIG_SYS_TEXT_BASE 0x4a000000 +#else +#define CONFIG_SYS_TEXT_BASE 0x42e00000 +#endif /* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here
- since it needs to fit in with the other values. By also #defining it
- we get warnings if the Kconfig value mismatches. */
@@ -148,8 +153,13 @@ #define CONFIG_SYS_MMC_MAX_DEVICE 4 #endif
+#ifndef CONFIG_MACH_SUN8I_V3S /* 64MB of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (64 << 20)) +#else +/* 2MB of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (2 << 20)) +#endif
/*
- Miscellaneous configurable options
@@ -280,7 +290,11 @@ extern int soft_i2c_gpio_scl;
- The amount of RAM to keep free at the top of RAM when relocating u-boot,
- to use as framebuffer. This must be a multiple of 4096.
*/ +#ifndef CONFIG_MACH_SUN8I_V3S #define CONFIG_SUNXI_MAX_FB_SIZE (16 << 20) +#else +#define CONFIG_SUNXI_MAX_FB_SIZE (2 << 20) +#endif
Do you need that? CONFIG_VIDEO is disabled, so there's no need to reserve space for a framebuffer.
/* Do we want to initialize a simple FB? */ #define CONFIG_VIDEO_DT_SIMPLEFB @@ -383,27 +397,49 @@ extern int soft_i2c_gpio_scl;
- 32M uncompressed kernel, 16M compressed kernel, 1M fdt,
- 1M script, 1M pxe and the ramdisk at the end.
*/
+#ifndef CONFIG_MACH_SUN8I_V3S +#define BOOTM_SIZE __stringify(0xa000000) #define KERNEL_ADDR_R __stringify(SDRAM_OFFSET(2000000)) #define FDT_ADDR_R __stringify(SDRAM_OFFSET(3000000)) #define SCRIPT_ADDR_R __stringify(SDRAM_OFFSET(3100000)) #define PXEFILE_ADDR_R __stringify(SDRAM_OFFSET(3200000)) #define RAMDISK_ADDR_R __stringify(SDRAM_OFFSET(3300000)) +#else +/*
- 64M RAM minus 2MB heap + 16MB for u-boot, stack, fb, etc.
- 16M uncompressed kernel, 8M compressed kernel, 1M fdt,
- 1M script, 1M pxe and the ramdisk at the end.
- */
+#define BOOTM_SIZE __stringify(0x2e00000) +#define KERNEL_ADDR_R __stringify(SDRAM_OFFSET(1000000)) +#define FDT_ADDR_R __stringify(SDRAM_OFFSET(1800000)) +#define SCRIPT_ADDR_R __stringify(SDRAM_OFFSET(1900000)) +#define PXEFILE_ADDR_R __stringify(SDRAM_OFFSET(1A00000)) +#define RAMDISK_ADDR_R __stringify(SDRAM_OFFSET(1B00000)) +#endif #endif
#define MEM_LAYOUT_ENV_SETTINGS \
- "bootm_size=0xa000000\0" \
- "bootm_size=" BOOTM_SIZE "\0" \ "kernel_addr_r=" KERNEL_ADDR_R "\0" \ "fdt_addr_r=" FDT_ADDR_R "\0" \ "scriptaddr=" SCRIPT_ADDR_R "\0" \ "pxefile_addr_r=" PXEFILE_ADDR_R "\0" \ "ramdisk_addr_r=" RAMDISK_ADDR_R "\0"
+#ifndef CONFIG_MACH_SUN8I_V3S #define DFU_ALT_INFO_RAM \ "dfu_alt_info_ram=" \ "kernel ram " KERNEL_ADDR_R " 0x1000000;" \ "fdt ram " FDT_ADDR_R " 0x100000;" \ "ramdisk ram " RAMDISK_ADDR_R " 0x4000000\0" +#else +#define DFU_ALT_INFO_RAM \
- "dfu_alt_info_ram=" \
- "kernel ram " KERNEL_ADDR_R " 0x800000;" \
- "fdt ram " FDT_ADDR_R " 0x100000;" \
- "ramdisk ram " RAMDISK_ADDR_R " 0x1000000\0"
+#endif
Do you even support DFU?
Thanks, Maxime