From: Enrico Leto enrico.leto@siemens.com
The signal integrity test generates pattern on DDR lines for certification. The signals must be as fast as possible and unidirectional.
The test is required from our HW team. The available u-boot memory test doesn't full fill the our requirements.
The test is planed to be used in all new siemens boards.
Signed-off-by: Enrico Leto enrico.leto@siemens.com Signed-off-by: Heiko Schocher hs@denx.de ---
board/siemens/capricorn/Kconfig | 2 + board/siemens/capricorn/Makefile | 1 + board/siemens/common/Kconfig | 4 + board/siemens/common/ddr_si_test.c | 348 +++++++++++++++++++++++++++++ 4 files changed, 355 insertions(+) create mode 100644 board/siemens/common/ddr_si_test.c
diff --git a/board/siemens/capricorn/Kconfig b/board/siemens/capricorn/Kconfig index 03a433df2aa..fe230971e97 100644 --- a/board/siemens/capricorn/Kconfig +++ b/board/siemens/capricorn/Kconfig @@ -21,3 +21,5 @@ config SPL_CMT depends on SPL help Enable SIemens SPL RAM test. + +source "board/siemens/common/Kconfig" diff --git a/board/siemens/capricorn/Makefile b/board/siemens/capricorn/Makefile index b8350d96d04..a03d54ef3b3 100644 --- a/board/siemens/capricorn/Makefile +++ b/board/siemens/capricorn/Makefile @@ -11,4 +11,5 @@ obj-y += spl.o obj-$(CONFIG_SPL_CMT) += spl_memory_test.o else obj-y += ../common/factoryset.o +obj-$(CONFIG_DDR_SI_TEST) += ../common/ddr_si_test.o endif diff --git a/board/siemens/common/Kconfig b/board/siemens/common/Kconfig index 131439fcfea..4ae12b1c973 100644 --- a/board/siemens/common/Kconfig +++ b/board/siemens/common/Kconfig @@ -1,2 +1,6 @@ config FACTORYSET bool + +config DDR_SI_TEST + bool "DDR signal integrity test implementations" + default y diff --git a/board/siemens/common/ddr_si_test.c b/board/siemens/common/ddr_si_test.c new file mode 100644 index 00000000000..c1f523eb3f4 --- /dev/null +++ b/board/siemens/common/ddr_si_test.c @@ -0,0 +1,348 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright Siemens AG 2023 + * + * DDR signal integrity test + * Check signals on DDR lines + * - signals must be as fast as possible and generate long burst + * - signals must be unidirectional (to DDR or from DDR only) + * + * Set pattern: define 2^n 32-bit patterns (up to 4) + * Addresses: must be multiple of 16 to avoid checks in loops + * Test functions + * - write: write pattern to memory area for iteration times + * - read: write pattern once to memory area, read for iteration times + */ + +#include <command.h> +#include <exports.h> +#include <time.h> +#if CONFIG_IS_ENABLED(AM33XX) +#include <asm/arch-am33xx/hardware_am33xx.h> +#include <asm/arch-am33xx/cpu.h> +#include <asm/io.h> +#endif + +/* enable some print for debugging */ +#ifdef PR_DEBUG + #define PDEBUG(fmt, args...) printf(fmt, ## args) +#else + #define PDEBUG(fmt, args...) +#endif + +/* define 4 32-bit patterns */ +#define MAX_PTN_SIZE (128) +#define PTN_ARRAY_SIZE (MAX_PTN_SIZE / (8 * sizeof(u32))) + +/* define test direction */ +#define DIR_READ 0 +#define DIR_WRITE 1 + +static union { + u64 l[2]; + u32 s[4]; + } test_pattern; +static int num_ptn32; + +#if CONFIG_IS_ENABLED(AM33XX) +static inline void wdt_disable(void) +{ + struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; + + writel(0xAAAA, &wdtimer->wdtwspr); + while (readl(&wdtimer->wdtwwps) != 0x0) + ; + writel(0x5555, &wdtimer->wdtwspr); + while (readl(&wdtimer->wdtwwps) != 0x0) + ; +} + +static inline void wdt_enable(void) +{ + struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; + + writel(0xBBBB, &wdtimer->wdtwspr); + while (readl(&wdtimer->wdtwwps) != 0x0) + ; + writel(0x4444, &wdtimer->wdtwspr); + while (readl(&wdtimer->wdtwwps) != 0x0) + ; +} +#else /* ! */ +static inline void wdt_disable(void) {} + +static inline void wdt_enable(void) {} +#endif /* CONFIG_IS_ENABLED(AM33XX) */ + +static int do_ddr_set_ptn(struct cmd_tbl *cmdtp, int flag, int argc, + char *const argv[]) +{ + int i, n; + + if (argc < 1) + return CMD_RET_USAGE; + + /* number of patterns: 2 exponent */ + n = argc - 1; + if (n > PTN_ARRAY_SIZE || (n & (n - 1))) + return CMD_RET_USAGE; + num_ptn32 = n; + + /* get patterns */ + for (i = 0; i < n; i++) + test_pattern.s[i] = simple_strtoul(argv[i + 1], NULL, 0); + + printf("Test pattern set\n"); + + return CMD_RET_SUCCESS; +} + +static int do_ddr_show_ptn(struct cmd_tbl *cmdtp, int flag, int argc, + char *const argv[]) +{ + if (!num_ptn32) { + printf("No pattern available\n"); + } else { + u32 *buf = test_pattern.s; + int len = num_ptn32; + int i; + + printf("Pattern: "); + for (i = 0 ; i < len; i++) + printf("0x%08X ", *buf++); + + printf("\n"); + } + + return CMD_RET_SUCCESS; +} + +static void ddr_read32(u64 start_addr, u64 n_word, unsigned long iter) +{ + while (iter--) { + register volatile u32 *addr = (u32 *)start_addr; + register u64 count = n_word; + + while (count) { + (void)*addr++; + PDEBUG("Read 0x%08X from 0x%p\n", val, addr - 1); + count--; + } + } +} + +static void ddr_read64(u64 start_addr, u64 n_word, unsigned long iter) +{ + while (iter--) { + register volatile u64 *addr = (u64 *)start_addr; + register u64 count = n_word; + + if (num_ptn32 == 4) + count *= 2; + + /* + * 64 & 128 bit pattern. Increase the nummber of read + * commands in the loop to generate longer burst signal + */ + while (count) { + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + (void)*addr++; + PDEBUG("Read 0x%016llX from 0x%p\n", val, addr - 1); + /* + * underflow cannot happen since n_word = end - + * start, end & start addresses are checked to be + * multiple of 16 + */ + count -= 8; + } + } +} + +static void ddr_write32(u64 start_addr, u64 n_word, unsigned long iter) +{ + while (iter--) { + register u32 *addr = (u32 *)start_addr; + register u32 ptn = *test_pattern.s; + register u64 count = n_word; + + while (count) { + PDEBUG("Write 0x%08X to 0x%p\n", ptn, addr); + *addr++ = ptn; + count--; + } + } +} + +static void ddr_write64(u64 start_addr, u64 n_word, unsigned long iter) +{ + while (iter--) { + register u64 *addr = (u64 *)start_addr; + register u64 ptnA = test_pattern.l[0]; + register u64 ptnB = test_pattern.l[1]; + register u64 count = n_word; + + if (num_ptn32 == 2) + ptnB = ptnA; + else + count *= 2; + + /* + * 64 & 128 bit pattern. Increase the nummber of write + * commands in the loop to generate longer burst signal + */ + while (count) { + PDEBUG("Write 0x%016llX to 0x%p\n", ptnA, addr); + *addr++ = ptnA; + PDEBUG("Write 0x%016llX to 0x%p\n", ptnB, addr); + *addr++ = ptnB; + PDEBUG("Write 0x%016llX to 0x%p\n", ptnA, addr); + *addr++ = ptnA; + PDEBUG("Write 0x%016llX to 0x%p\n", ptnB, addr); + *addr++ = ptnB; + PDEBUG("Write 0x%016llX to 0x%p\n", ptnA, addr); + *addr++ = ptnA; + PDEBUG("Write 0x%016llX to 0x%p\n", ptnB, addr); + *addr++ = ptnB; + PDEBUG("Write 0x%016llX to 0x%p\n", ptnA, addr); + *addr++ = ptnA; + PDEBUG("Write 0x%016llX to 0x%p\n", ptnB, addr); + *addr++ = ptnB; + /* + * underflow cannot happen since n_word = end - + * start, end & start addresses are checked to be + * multiple of 16 + */ + count -= 8; + } + } +} + +static int do_ddr_si_test(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) +{ + u64 start_addr, end_addr, n_word; + u64 ts_start, ts_end; + unsigned long iteration, wr_iter; + int direction, i; + + if (argc < 3 || argc > 4) + return CMD_RET_USAGE; + + /* get arguments */ + direction = strcmp(argv[0], "read") ? DIR_WRITE : DIR_READ; + start_addr = simple_strtoul(argv[1], NULL, 0); + end_addr = simple_strtoul(argv[2], NULL, 0); + iteration = simple_strtoul(argv[3], NULL, 10); + + n_word = (end_addr - start_addr) / (num_ptn32 * 4); + printf("\nDDR signal integrity %s test: start\n", argv[0]); + /* checks */ + if (start_addr & 0xF) { + printf("ERROR: start_address should be 16 bytes aligned\n\n"); + return CMD_RET_USAGE; + } + + if (end_addr & 0xF) { + printf("ERROR: end_address should be 16 bytes aligned\n\n"); + return CMD_RET_USAGE; + } + + if (start_addr >= end_addr) { + printf("ERROR: end_address is not bigger than start_address\n\n"); + return CMD_RET_USAGE; + } + + if (!iteration) { + printf("ERROR: no iteration specified\n\n"); + return CMD_RET_USAGE; + } + + if (!num_ptn32) { + printf("ERROR: no test pattern specified\n\n"); + return CMD_RET_USAGE; + } + + /* print parameters */ + printf("start_address = 0x%016llX\n", start_addr); + printf("end_address = 0x%016llX\n", end_addr); + printf("iterations = %lu\n", iteration); + + /* print pattern */ + printf("test pattern 0x"); + for (i = 0; i < num_ptn32; i++) + printf("%08X", test_pattern.s[i]); + + printf("\n"); + + wdt_disable(); + + /* writing */ + printf("Writing..\n"); + ts_start = get_timer_us(0); + + if (direction == DIR_READ) + wr_iter = 1; + else + wr_iter = iteration; + + if (num_ptn32 == 1) + ddr_write32(start_addr, n_word, wr_iter); + else + ddr_write64(start_addr, n_word, wr_iter); + + ts_end = get_timer_us(0); + + /* reading */ + if (direction == DIR_READ) { + printf("Reading..\n"); + /* we need read time, just overwrite */ + ts_start = get_timer_us(0); + + if (num_ptn32 == 1) + ddr_read32(start_addr, n_word, iteration); + else + ddr_read64(start_addr, n_word, iteration); + + ts_end = get_timer_us(0); + } + + wdt_enable(); + + /* print stats */ + printf("DONE."); + printf(" Bytes=%llu ", n_word * num_ptn32 * 4 * iteration); + printf(" Time=%llu us ", ts_end - ts_start); + printf("\nDDR signal integrity %s test: end\n", argv[0]); + + return CMD_RET_SUCCESS; +} + +static char ddr_si_help_text[] = + "- DDR signal integrity test\n\n" + "ddr_si setptn <pattern> [<pattern>] : set [1,2,4] 32-bit patterns\n" + "ddr_si showptn : show patterns\n" + "ddr_si read <start> <end> <iterations> : run test for reading\n" + "ddr_si write <start> <end> <iterations> : run test for writing\n" + "\nWith\n" + "\t<pattern>: 32-bit pattern in hex format\n" + "\t<start>: test start address in hex format\n" + "\t<end>: test end address in hex format\n" + "\t<iterations>: number of iterations\n"; + +U_BOOT_CMD_WITH_SUBCMDS(ddr_si, "DDR si test", ddr_si_help_text, + U_BOOT_SUBCMD_MKENT(setptn, 5, 0, do_ddr_set_ptn), + U_BOOT_SUBCMD_MKENT(showptn, 1, 0, do_ddr_show_ptn), + U_BOOT_SUBCMD_MKENT(read, 4, 0, do_ddr_si_test), + U_BOOT_SUBCMD_MKENT(write, 4, 0, do_ddr_si_test));