On 11.05.20 11:53, Peng Fan wrote:
From: Ye Li ye.li@nxp.com
Enable print to show the DRAM rate of current setting and training result.
Reviewed-by: Peng Fan peng.fan@nxp.com Signed-off-by: Ye Li ye.li@nxp.com Signed-off-by: Peng Fan peng.fan@nxp.com
This changes the boottime, too. The printf() are really useful only for debugging, IMHO it is better to let it as it is. If something is going wrong, one set DEBUG to get the output.
Regards, Stefano
drivers/ddr/imx/imx8m/ddr_init.c | 7 ++++--- drivers/ddr/imx/imx8m/ddrphy_utils.c | 2 +- 2 files changed, 5 insertions(+), 4 deletions(-)
diff --git a/drivers/ddr/imx/imx8m/ddr_init.c b/drivers/ddr/imx/imx8m/ddr_init.c index f573a778d9..a1d2d21692 100644 --- a/drivers/ddr/imx/imx8m/ddr_init.c +++ b/drivers/ddr/imx/imx8m/ddr_init.c @@ -95,7 +95,7 @@ int ddr_init(struct dram_timing_info *dram_timing) unsigned int tmp, initial_drate, target_freq; int ret;
- debug("DDRINFO: start DRAM init\n");
printf("DDRINFO: start DRAM init\n");
/* Step1: Follow the power up procedure */ if (is_imx8mq()) {
@@ -118,6 +118,7 @@ int ddr_init(struct dram_timing_info *dram_timing)
initial_drate = dram_timing->fsp_msg[0].drate; /* default to the frequency point 0 clock */
- printf("DDRINFO: DRAM rate %dMTS\n", initial_drate);
ddrphy_init_set_dfi_clk(initial_drate);
/* D-aasert the presetn */ @@ -184,7 +185,7 @@ int ddr_init(struct dram_timing_info *dram_timing) tmp = reg32_read(DDRPHY_CalBusy(0)); } while ((tmp & 0x1));
- debug("DDRINFO:ddrphy calibration done\n");
printf("DDRINFO:ddrphy calibration done\n");
/* Step15: Set SWCTL.sw_done to 0 */ reg32_write(DDRC_SWCTL(0), 0x00000000);
@@ -236,7 +237,7 @@ int ddr_init(struct dram_timing_info *dram_timing)
/* enable port 0 */ reg32_write(DDRC_PCTRL_0(0), 0x00000001);
- debug("DDRINFO: ddrmix config done\n");
printf("DDRINFO: ddrmix config done\n");
board_dram_ecc_scrub();
diff --git a/drivers/ddr/imx/imx8m/ddrphy_utils.c b/drivers/ddr/imx/imx8m/ddrphy_utils.c index 9ac7ca923c..9d2378d7dd 100644 --- a/drivers/ddr/imx/imx8m/ddrphy_utils.c +++ b/drivers/ddr/imx/imx8m/ddrphy_utils.c @@ -97,7 +97,7 @@ int wait_ddrphy_training_complete(void) debug("Training PASS\n"); return 0; } else if (mail == 0xff) {
debug("Training FAILED\n");
printf("Training FAILED\n"); return -1;