Boot Rom wouldn't initialize sdmmc while booting from eMMC. We need to setup sdmmc gpio, otherwise we will hit an error below:
=>mmc info blk_get_device: if_type=6, devnum=0: dwmmc@ff0c0000.blk, 6, 0 uclass_find_device_by_seq: 0 -1 uclass_find_device_by_seq: 0 0 - -1 -1 - -1 0 - found uclass_find_device_by_seq: 0 1 - -1 -1 - -1 0 - not found fdtdec_get_int_array: interrupts get_prop_check_min_len: interrupts Buswidth = 1, clock: 0 Buswidth = 1, clock: 400000 Sending CMD0 dwmci_send_cmd: Timeout on data busy dwmci_send_cmd: Timeout on data busy dwmci_send_cmd: Timeout on data busy dwmci_send_cmd: Timeout on data busy
This reverts commit 6efeeea79c880d3dd262e0dca9da2687f0ab68c9.
Signed-off-by: Ziyuan Xu xzy.xu@rock-chips.com Acked-by: Simon Glass sjg@chromium.org Tested-by: Simon Glass sjg@chromium.org ---
Changes in v2: None
arch/arm/mach-rockchip/rk3288-board-spl.c | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c index ed14023..1b74173 100644 --- a/arch/arm/mach-rockchip/rk3288-board-spl.c +++ b/arch/arm/mach-rockchip/rk3288-board-spl.c @@ -116,6 +116,9 @@ static void configure_l2ctlr(void) #ifdef CONFIG_SPL_MMC_SUPPORT static int configure_emmc(struct udevice *pinctrl) { +#if !defined(CONFIG_TARGET_ROCK2) && !defined(CONFIG_TARGET_FIREFLY_RK3288) && \ + !defined(CONFIG_TARGET_EVB_RK3288) + struct gpio_desc desc; int ret;
@@ -145,7 +148,7 @@ static int configure_emmc(struct udevice *pinctrl) debug("gpio value ret=%d\n", ret); return ret; } - +#endif return 0; } #endif @@ -249,20 +252,17 @@ void spl_board_init(void) debug("%s: Cannot find pinctrl device\n", __func__); goto err; } + #ifdef CONFIG_SPL_MMC_SUPPORT - if (!IS_ENABLED(CONFIG_TARGET_ROCK2) && - !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288) && - !IS_ENABLED(CONFIG_TARGET_EVB_RK3288)) { - ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD); - if (ret) { - debug("%s: Failed to set up SD card\n", __func__); - goto err; - } - ret = configure_emmc(pinctrl); - if (ret) { - debug("%s: Failed to set up eMMC\n", __func__); - goto err; - } + ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD); + if (ret) { + debug("%s: Failed to set up SD card\n", __func__); + goto err; + } + ret = configure_emmc(pinctrl); + if (ret) { + debug("%s: Failed to set up eMMC\n", __func__); + goto err; } #endif