The displays need to use NPLL and also select some new peripheral clocks. Add support for these to the clock driver.
Signed-off-by: Simon Glass sjg@chromium.org ---
drivers/clk/clk_rk3288.c | 174 +++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 170 insertions(+), 4 deletions(-)
diff --git a/drivers/clk/clk_rk3288.c b/drivers/clk/clk_rk3288.c index d3c14dd..42d2f85 100644 --- a/drivers/clk/clk_rk3288.c +++ b/drivers/clk/clk_rk3288.c @@ -235,6 +235,124 @@ static int rkclk_configure_ddr(struct rk3288_cru *cru, struct rk3288_grf *grf, return 0; }
+#ifndef CONFIG_SPL_BUILD +#define VCO_MAX_KHZ 2200000 +#define VCO_MIN_KHZ 440000 +#define FREF_MAX_KHZ 2200000 +#define FREF_MIN_KHZ 269 + +static int pll_para_config(ulong freq_hz, struct pll_div *div, uint *ext_div) +{ + uint ref_khz = OSC_HZ / 1000, nr, nf = 0; + uint fref_khz; + uint diff_khz, best_diff_khz; + const uint max_nr = 1 << 6, max_nf = 1 << 12, max_no = 1 << 4; + uint vco_khz; + uint no = 1; + uint freq_khz = freq_hz / 1000; + + if (!freq_hz) { + printf("%s: the frequency can not be 0 Hz\n", __func__); + return -EINVAL; + } + + no = DIV_ROUND_UP(VCO_MIN_KHZ, freq_khz); + if (ext_div) { + *ext_div = DIV_ROUND_UP(no, max_no); + no = DIV_ROUND_UP(no, *ext_div); + } + + /* only even divisors (and 1) are supported */ + if (no > 1) + no = DIV_ROUND_UP(no, 2) * 2; + + vco_khz = freq_khz * no; + if (ext_div) + vco_khz *= *ext_div; + + if (vco_khz < VCO_MIN_KHZ || vco_khz > VCO_MAX_KHZ || no > max_no) { + printf("%s: Cannot find out a supported VCO for Frequency (%luHz).\n", + __func__, freq_hz); + return -1; + } + + div->no = no; + + best_diff_khz = vco_khz; + for (nr = 1; nr < max_nr && best_diff_khz; nr++) { + fref_khz = ref_khz / nr; + if (fref_khz < FREF_MIN_KHZ) + break; + if (fref_khz > FREF_MAX_KHZ) + continue; + + nf = vco_khz / fref_khz; + if (nf >= max_nf) + continue; + diff_khz = vco_khz - nf * fref_khz; + if (nf + 1 < max_nf && diff_khz > fref_khz / 2) { + nf++; + diff_khz = fref_khz - diff_khz; + } + + if (diff_khz >= best_diff_khz) + continue; + + best_diff_khz = diff_khz; + div->nr = nr; + div->nf = nf; + } + + if (best_diff_khz > 4 * 1000) { + printf("%s: Failed to match output frequency %lu, difference is %u Hz, exceed 4MHZ\n", + __func__, freq_hz, best_diff_khz * 1000); + return -EINVAL; + } + + return 0; +} + +static int rockchip_vop_set_clk(struct rk3288_cru *cru, struct rk3288_grf *grf, + int periph, unsigned int rate_hz) +{ + struct pll_div npll_config = {0}; + u32 lcdc_div; + int ret; + + ret = pll_para_config(rate_hz, &npll_config, &lcdc_div); + if (ret) + return ret; + + rk_clrsetreg(&cru->cru_mode_con, NPLL_MODE_MASK << NPLL_MODE_SHIFT, + NPLL_MODE_SLOW << NPLL_MODE_SHIFT); + rkclk_set_pll(cru, CLK_NEW, &npll_config); + + /* waiting for pll lock */ + while (1) { + if (readl(&grf->soc_status[1]) & SOCSTS_NPLL_LOCK) + break; + udelay(1); + } + + rk_clrsetreg(&cru->cru_mode_con, NPLL_MODE_MASK << NPLL_MODE_SHIFT, + NPLL_MODE_NORMAL << NPLL_MODE_SHIFT); + + /* vop dclk source clk: npll,dclk_div: 1 */ + switch (periph) { + case DCLK_VOP0: + rk_clrsetreg(&cru->cru_clksel_con[27], 0xff << 8 | 3 << 0, + (lcdc_div - 1) << 8 | 2 << 0); + break; + case DCLK_VOP1: + rk_clrsetreg(&cru->cru_clksel_con[29], 0xff << 8 | 3 << 6, + (lcdc_div - 1) << 8 | 2 << 6); + break; + } + + return 0; +} +#endif + #ifdef CONFIG_SPL_BUILD static void rkclk_init(struct rk3288_cru *cru, struct rk3288_grf *grf) { @@ -559,6 +677,7 @@ ulong rk3288_get_periph_rate(struct udevice *dev, int periph) ulong rk3288_set_periph_rate(struct udevice *dev, int periph, ulong rate) { struct rk3288_clk_priv *priv = dev_get_priv(dev); + struct rk3288_cru *cru = priv->cru; struct udevice *gclk; ulong new_rate, gclk_rate; int ret; @@ -571,15 +690,62 @@ ulong rk3288_set_periph_rate(struct udevice *dev, int periph, ulong rate) case HCLK_EMMC: case HCLK_SDMMC: case HCLK_SDIO0: - new_rate = rockchip_mmc_set_clk(priv->cru, gclk_rate, periph, - rate); + new_rate = rockchip_mmc_set_clk(cru, gclk_rate, periph, rate); break; case SCLK_SPI0: case SCLK_SPI1: case SCLK_SPI2: - new_rate = rockchip_spi_set_clk(priv->cru, gclk_rate, periph, - rate); + new_rate = rockchip_spi_set_clk(cru, gclk_rate, periph, rate); break; +#ifndef CONFIG_SPL_BUILD + case DCLK_VOP0: + case DCLK_VOP1: + new_rate = rockchip_vop_set_clk(cru, priv->grf, periph, rate); + break; + case SCLK_EDP_24M: + /* clk_edp_24M source: 24M */ + rk_setreg(&cru->cru_clksel_con[28], 1 << 15); + + /* rst edp */ + rk_setreg(&cru->cru_clksel_con[6], 1 << 15); + udelay(1); + rk_clrreg(&cru->cru_clksel_con[6], 1 << 15); + new_rate = rate; + break; + case ACLK_VOP0: + case ACLK_VOP1: { + u32 div; + + /* vop aclk source clk: cpll */ + div = CPLL_HZ / rate; + assert((div - 1 < 64) && (div * rate == CPLL_HZ)); + + switch (periph) { + case ACLK_VOP0: + rk_clrsetreg(&cru->cru_clksel_con[31], + 3 << 6 | 0x1f << 0, + 0 << 6 | (div - 1) << 0); + break; + case ACLK_VOP1: + rk_clrsetreg(&cru->cru_clksel_con[31], + 3 << 14 | 0x1f << 8, + 0 << 14 | (div - 1) << 8); + break; + } + new_rate = rate; + break; + } + case PCLK_HDMI_CTRL: + /* enable pclk hdmi ctrl */ + rk_clrreg(&cru->cru_clkgate_con[16], 1 << 9); + + /* software reset hdmi */ + rk_setreg(&cru->cru_clkgate_con[7], 1 << 9); + udelay(1); + rk_clrreg(&cru->cru_clkgate_con[7], 1 << 9); + new_rate = rate; + break; +#endif default: return -ENOENT; }