Hi Mark,
On 2024-05-11 21:57, Mark Kettenis wrote:
Date: Sat, 11 May 2024 20:47:40 +0200 From: Jonas Karlman jonas@kwiboo.se
Hi Jonas & Alex,
Hi Alex,
On 2024-05-11 19:44, Alex Bee wrote:
Hi Jonas,
Am 11.05.24 um 13:28 schrieb Jonas Karlman:
This series add gpio request() and pinctrl gpio_request_enable() ops so that a gpio requested pin automatically use gpio pinmux and U-Boot behaves more similar to Linux kernel.
I'm not sure that's a good idea. While linux does it the same way, we really shouldn't expect every software/os/ … which uses DT (now or in future) to implicitly switch the pin function when using a pin as gpio. So the real fix would probably be to add the the correct pinctrl settings to the upstream DT of those boards and sync it later on (not sure those if those SoCs already using OF_UPSTREAM) and leave the -u-boot.dtsi-"hack" alone for now.
I missed Alex's mail, but OpenBSD certainly is one of the OSes that could break if the pinctrl settings get removed. We currently have no code to automatically mux the gpio pins on these Rockchip SoCs. I suppose as long as U-Boot probes the PCIe bus, the pins will already be muxed correctly and things will continue to work. But I think there are certain boot scenarios where this won't happen.
The control FDT on the known affected boards was only patched to prevent the boards from a full device freeze when PCIe was enumerated. An OS should probably not depend on a workaround made for U-Boot use.
Is it common for *BDS to use the control FDT or is it more common that a separate .dtb-file to be loaded during boot?
To recap, the issue on e.g. ROCK 3A is that the upstream DT use pinctrl to signal PCIE30X2 CLKREQn_M1/WAKEn_M1/PERSTn_M1 function, DT also specify a reset-gpios prop pointing on PERSTn_M1. To me this seem like a correct description of HW.
When U-Boot probe the PCIE30X2 device the pinctrl driver would automatically configure CLKREQn_M1/WAKEn_M1/PERSTn_M1 function.
When U-Boot RK PCIe driver try to use the reset-gpios pin the device would freeze unless the PERSTn pin is first re-configured for gpio use.
Current workaround in U-Boot throws away the existing upstream pinctrl and replace it to only configure gpio func on the PERSTn pin. This also leaves the CLKREQn and WAKEn to incorrectly use gpio func.
With this series I try to cleanup the old workaround that I added without much insight beyond: device no longer freeze and nvme "works" :-)
I've wondered in the past what the purpose of the gpio-ranges properties was. I never considered that they could be used to automatically mux the pins for GPIO since the gpio-ranges mapping provides no indication of what the correct pin settings arefor the GPIO pins.
The gpio-ranges prop is only used to provide details on how the pins are mapped between gpio and pin controller. It is not used to change any muxing. But the property is required to make the U-Boot helpers pinctrl_gpio_request()/pinctrl_gpio_free() work and figure out what pinctrl udevice to use if another driver use e.g. gpio_request_by_name() to request use of a pin for gpio use.
Keep in mind that this series should not change any behavior except for the special case when DT pinctrl may configure a pin for non-gpio function and later U-Boot request the pin to be used for gpio.
I fully agree that the pinctrl for the problematic boards should be corrected in upstream DT, but that is a separate issue and should not block adding support for the request()/gpio_request_enable() ops.
While the pcie reset-gpios full board freeze that was my driving factor to fully implement the gpio request() ops it is not the only use case, using the gpio cmd on a pin that use a non-gpio pinmux is another.
Or do you see any technical issue with having the gpio request() ops implemented and having it ensure gpio pinmux is used on a gpio requested pin? Similar to how gpio/pinctrl is behaving in Linux and on some other platforms in U-Boot?
Well, it removes the incentive to fix the upstream DTs and would make it harder to notice missing pinctrls in the DTs.
I can understand that, but gpio pinmux is default so any missing pinctrl would still cause issues, this changes nothing in that regard.
This only affect if pinctrl exists and pin gets configured for non-gpio function use. And later a driver/cmd tries to use such pin for gpio use. Before this patch the use of gpio_request() would not change the pin mux for gpio use. After this series when code explicily request a pin for gpio use the pinctrl driver gets notified that it should change pinmux of the pin for gpio use.
Regards, Jonas
Cheers,
Mark
Alex
With the gpio and pinctrl ops implemented this series also remove a PCIe reset-gpios related device lock-up workaround from board u-boot.dtsi.
PX30, RK3066, RK3188, RK356x and RK3588 are the only SoCs that currently define gpio-ranges props and is affected by this series.
A follow up series adding support for the pinmux status cmd will also add gpio-ranges props for remaining RK SoCs.
Jonas Karlman (4): pinctrl: rockchip: Add gpio_request_enable() ops gpio: rockchip: Add request() ops rockchip: rk3568-rock-3a: Drop PCIe reset-gpios workaround rockchip: rk3568-radxa-e25: Drop PCIe reset-gpios workaround
arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi | 12 ------- arch/arm/dts/rk3568-rock-3a-u-boot.dtsi | 12 ------- drivers/gpio/rk_gpio.c | 10 ++++++ .../pinctrl/rockchip/pinctrl-rockchip-core.c | 31 +++++++++++++++++++ 4 files changed, 41 insertions(+), 24 deletions(-)