Just some minor style fixes. No functional change.
Signed-off-by: Sam Protsenko semen.protsenko@linaro.org --- drivers/serial/serial_s5p.c | 34 ++++++++++++++++++---------------- 1 file changed, 18 insertions(+), 16 deletions(-)
diff --git a/drivers/serial/serial_s5p.c b/drivers/serial/serial_s5p.c index 6d316ccaf31d..c24d9bca84c9 100644 --- a/drivers/serial/serial_s5p.c +++ b/drivers/serial/serial_s5p.c @@ -50,9 +50,9 @@ enum {
/* Information about a serial port */ struct s5p_serial_plat { - struct s5p_uart *reg; /* address of registers in physical memory */ - u8 reg_width; /* register width */ - u8 port_id; /* uart port number */ + struct s5p_uart *reg; /* address of registers in physical memory */ + u8 reg_width; /* register width */ + u8 port_id; /* uart port number */ u8 rx_fifo_count_shift; u8 tx_fifo_count_shift; u32 rx_fifo_count_mask; @@ -65,7 +65,7 @@ struct s5p_serial_plat { * The coefficient, used to calculate the baudrate on S5P UARTs is * calculated as * C = UBRDIV * 16 + number_of_set_bits_in_UDIVSLOT - * however, section 31.6.11 of the datasheet doesn't recomment using 1 for 1, + * however, section 31.6.11 of the datasheet doesn't recommend using 1 for 1, * 3 for 2, ... (2^n - 1) for n, instead, they suggest using these constants: */ static const int udivslot[] = { @@ -251,10 +251,10 @@ static int s5p_serial_of_to_plat(struct udevice *dev) }
static const struct dm_serial_ops s5p_serial_ops = { - .putc = s5p_serial_putc, - .pending = s5p_serial_pending, - .getc = s5p_serial_getc, - .setbrg = s5p_serial_setbrg, + .putc = s5p_serial_putc, + .pending = s5p_serial_pending, + .getc = s5p_serial_getc, + .setbrg = s5p_serial_setbrg, };
static const struct udevice_id s5p_serial_ids[] = { @@ -264,13 +264,13 @@ static const struct udevice_id s5p_serial_ids[] = { };
U_BOOT_DRIVER(serial_s5p) = { - .name = "serial_s5p", - .id = UCLASS_SERIAL, - .of_match = s5p_serial_ids, - .of_to_plat = s5p_serial_of_to_plat, + .name = "serial_s5p", + .id = UCLASS_SERIAL, + .of_match = s5p_serial_ids, + .of_to_plat = s5p_serial_of_to_plat, .plat_auto = sizeof(struct s5p_serial_plat), - .probe = s5p_serial_probe, - .ops = &s5p_serial_ops, + .probe = s5p_serial_probe, + .ops = &s5p_serial_ops, }; #endif
@@ -298,10 +298,12 @@ static inline void _debug_uart_putc(int ch) struct s5p_uart *uart = (struct s5p_uart *)CONFIG_VAL(DEBUG_UART_BASE);
#if IS_ENABLED(CONFIG_ARCH_APPLE) - while (readl(&uart->ufstat) & S5L_TX_FIFO_FULL); + while (readl(&uart->ufstat) & S5L_TX_FIFO_FULL) + ; writel(ch, &uart->utxh); #else - while (readl(&uart->ufstat) & S5P_TX_FIFO_FULL); + while (readl(&uart->ufstat) & S5P_TX_FIFO_FULL) + ; writeb(ch, &uart->utxh); #endif }