Hello,
[snip]
+/* DDR SDRAM control configuration 2 (DDR_SDRAM_CFG_2) */ +static void set_ddr_sdram_cfg_2(fsl_memctl_config_regs_t *ddr,
const memctl_options_t *popts)+{
- unsigned int frc_sr = 0; /* Force self refresh */
- unsigned int sr_ie = 0; /* Self-refresh interrupt enable */
- unsigned int dll_rst_dis; /* DLL reset disable */
- unsigned int dqs_cfg; /* DQS configuration */
- unsigned int odt_cfg; /* ODT configuration */
- unsigned int num_pr; /* Number of posted refreshes */
- unsigned int obc_cfg; /* On-The-Fly Burst Chop Cfg */
- unsigned int ap_en; /* Address Parity Enable */
- unsigned int d_init; /* DRAM data initialization */
- unsigned int rcw_en = 0; /* Register Control Word Enable */
- unsigned int md_en = 0; /* Mirrored DIMM Enable */
- dll_rst_dis = 1; /* Make this configurable */
- dqs_cfg = popts->DQS_config;
- if (popts->cs_local_opts[0].odt_rd_cfg
|| popts->cs_local_opts[0].odt_wr_cfg) {/* FIXME */odt_cfg = 2;- } else {
odt_cfg = 0;- }
- num_pr = 1; /* Make this configurable */
- /*
* 8572 manual says* {TIMING_CFG_1[PRETOACT]* + [DDR_SDRAM_CFG_2[NUM_PR]* * ({EXT_REFREC || REFREC} + 8 + 2)]}* << DDR_SDRAM_INTERVAL[REFINT]*/- obc_cfg = 0; /* Make this configurable? */
- ap_en = 0; /* Make this configurable? */
+#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /* Use the DDR controller to auto initialize memory. */
- d_init = 1;
- ddr->ddr_data_init = CONFIG_MEM_INIT_VALUE;
- debug("DDR: ddr_data_init = 0x%08x\n", ddr->ddr_data_init);
+#else
- /* Memory will be initialized via DMA, or not at all. */
- d_init = 0;
+#endif
I'm using the current head (33aa4eac66b71c797bbc13b3afe432a2132947d4) on a mpc8572-based board. It uses DDR2 and has support for ECC. While enabling ECC support, I noticed that the "old" CONFIG_ECC_INIT_VIA_DDRCONTROLLER define is still being used to enable memory initialization on bootup while a new ECC_init_using_memctl field in the memctl_options_s structure is also present.
Currently it looks like ECC_init_using_memctl doesn't do anything and is only referenced in one location below:
- /* Pick ECC modes */
+#ifdef CONFIG_DDR_ECC
- popts->ECC_mode = 1; /* 0 = disabled, 1 = enabled */
+#else
- popts->ECC_mode = 0; /* 0 = disabled, 1 = enabled */
+#endif
- popts->ECC_init_using_memctl = 1; /* 0 = use DMA, 1 = use memctl */
The intended functionality of CONFIG_ECC_INIT_VIA_DDRCONTROLLER and ECC_init_using_memctl seem to be the same, but only one of them is being used, and they currently are unrelated which is a bit confusing.
Should the ECC_init_using_memctl field be removed, or is the intention to replace CONFIG_ECC_INIT_VIA_DDRCONTROLLER functionality with ECC_init_using_memctl as some point?
Thanks for any insight, Peter