From: Pavel Machek pavel@denx.de
The dw_mmc driver was responding to errors with debug(). Change that to prinf()/puts() respectively so that any errors are immediately obvious. Also adjust english in comments.
Signed-off-by: Pavel Machek pavel@denx.de Signed-off-by: Marek Vasut marex@denx.de Cc: Chin Liang See clsee@altera.com Cc: Dinh Nguyen dinguyen@altera.com Cc: Albert Aribaud albert.u.boot@aribaud.net Cc: Tom Rini trini@ti.com Cc: Wolfgang Denk wd@denx.de Cc: Pavel Machek pavel@denx.de Cc: Pantelis Antoniou panto@antoniou-consulting.com --- drivers/mmc/dw_mmc.c | 34 ++++++++++++++++++++++------------ 1 file changed, 22 insertions(+), 12 deletions(-)
diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c index 0df30bc..785eed5 100644 --- a/drivers/mmc/dw_mmc.c +++ b/drivers/mmc/dw_mmc.c @@ -119,7 +119,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
while (dwmci_readl(host, DWMCI_STATUS) & DWMCI_BUSY) { if (get_timer(start) > timeout) { - printf("Timeout on data busy\n"); + printf("%s: Timeout on data busy\n", __func__); return TIMEOUT; } } @@ -177,14 +177,24 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, } }
- if (i == retry) + if (i == retry) { + printf("%s: Timeout.\n", __func__); return TIMEOUT; + }
if (mask & DWMCI_INTMSK_RTO) { - debug("Response Timeout..\n"); + /* + * Timeout here is not necessarily fatal. (e)MMC cards + * will splat here when they receive CMD55 as they do + * not support this command and that is exactly the way + * to tell them apart from SD cards. Thus, this output + * below shall be debug(). eMMC cards also do not favor + * CMD8, please keep that in mind. + */ + debug("%s: Response Timeout.\n", __func__); return TIMEOUT; } else if (mask & DWMCI_INTMSK_RE) { - debug("Response Error..\n"); + printf("%s: Response Error.\n", __func__); return -1; }
@@ -204,7 +214,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, do { mask = dwmci_readl(host, DWMCI_RINTSTS); if (mask & (DWMCI_DATA_ERR | DWMCI_DATA_TOUT)) { - debug("DATA ERROR!\n"); + printf("%s: DATA ERROR!\n", __func__); return -1; } } while (!(mask & DWMCI_INTMSK_DTO)); @@ -232,16 +242,16 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq) if ((freq == host->clock) || (freq == 0)) return 0; /* - * If host->get_mmc_clk didn't define, + * If host->get_mmc_clk isn't defined, * then assume that host->bus_hz is source clock value. - * host->bus_hz should be set from user. + * host->bus_hz should be set by user. */ if (host->get_mmc_clk) sclk = host->get_mmc_clk(host); else if (host->bus_hz) sclk = host->bus_hz; else { - printf("Didn't get source clock value..\n"); + printf("%s: Didn't get source clock value.\n", __func__); return -EINVAL; }
@@ -260,7 +270,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq) do { status = dwmci_readl(host, DWMCI_CMD); if (timeout-- < 0) { - printf("TIMEOUT error!!\n"); + printf("%s: Timeout!\n", __func__); return -ETIMEDOUT; } } while (status & DWMCI_CMD_START); @@ -275,7 +285,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq) do { status = dwmci_readl(host, DWMCI_CMD); if (timeout-- < 0) { - printf("TIMEOUT error!!\n"); + printf("%s: Timeout!\n", __func__); return -ETIMEDOUT; } } while (status & DWMCI_CMD_START); @@ -290,7 +300,7 @@ static void dwmci_set_ios(struct mmc *mmc) struct dwmci_host *host = (struct dwmci_host *)mmc->priv; u32 ctype, regs;
- debug("Buswidth = %d, clock: %d\n",mmc->bus_width, mmc->clock); + debug("Buswidth = %d, clock: %d\n", mmc->bus_width, mmc->clock);
dwmci_setup_bus(host, mmc->clock); switch (mmc->bus_width) { @@ -329,7 +339,7 @@ static int dwmci_init(struct mmc *mmc) dwmci_writel(host, DWMCI_PWREN, 1);
if (!dwmci_wait_reset(host, DWMCI_RESET_ALL)) { - debug("%s[%d] Fail-reset!!\n",__func__,__LINE__); + printf("%s[%d] Fail-reset!!\n", __func__, __LINE__); return -1; }