Fixes: commit a919e51161b58ed7e6e663daba99ab7d558808f3 mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
Fixes ecclayout mismatch introduced in above commit for following ecc-schemes: - OMAP_ECC_BCH4_CODE_HW_DETECTION_SW - OMAP_ECC_BCH8_CODE_HW_DETECTION_SW However, this patch also touches other ecc-schemes as the fix required refactoring common code, into ecc-scheme specific code.
This patch aligns ecc-layout for below ecc-schemes as per reference [1],[2],[3]
+---+------------+-------------++-------------+-------------+ |OOB|BCH8_CODE_HW|BCH8_CODE_HW_||HAM1_CODE_HW |HAM1_CODE_HW | |pos| | DETECTION_SW||(x8 device) |(x16 device) | +---+------------+-------------++-------------+-------------+ | 0 |BADBLK_MARK | BADBLK_MARK || BADBLK_MARK | BADBLK_MARK | | 1 |BADBLK_MARK | BADBLK_MARK || eccpos[0] | BADBLK_MARK | | 2 | eccpos[0] | eccpos[0] || eccpos[1] | eccpos[0] | | 3 | eccpos[1] | eccpos[1] || eccpos[2] | eccpos[1] | | 4 | eccpos[2] | eccpos[2] || eccpos[3] | eccpos[2] | | 5 | eccpos[3] | eccpos[3] || eccpos[4] | eccpos[3] | | 6 | eccpos[4] | eccpos[4] || eccpos[5] | eccpos[4] | | 7 | eccpos[5] | eccpos[5] || eccpos[6] | eccpos[5] | | 8 | eccpos[6] | eccpos[6] || eccpos[7] | eccpos[6] | | 9 | eccpos[7] | eccpos[7] || eccpos[8] | eccpos[7] | |10 | eccpos[8] | eccpos[8] || eccpos[9] | eccpos[8] | |11 | eccpos[9] | eccpos[9] || eccpos[10] | eccpos[9] | |12 | eccpos[10] | eccpos[10] || eccpos[11] | eccpos[10] | |13 | eccpos[11] | eccpos[11] || oobfree[0] | eccpos[11] | |14 | eccpos[12] | eccpos[12] || oobfree[1] | oobfree[0] | |15 | eccpos[13] | <reserved> || oobfree[2] | oobfree[1] | +---+------------+-------------++-------------+-------------+ |16 | eccpos[14] | eccpos[13] || oobfree[3] | oobfree[2] | |...| [...] | [...] || [...] | [...] | |56 | eccpos[54] | eccpos[51] || oobfree[43] | oobfree[42] | |57 | eccpos[55] | <reserved> || oobfree[44] | oobfree[43] | +===+============+=============+==============+=============+ |58 | oobfree[0] | oobfree[0] || oobfree[45] | oobfree[44] | |59 | oobfree[1] | oobfree[1] || oobfree[46] | oobfree[45] | |60 | oobfree[2] | oobfree[2] || oobfree[47] | oobfree[46] | |61 | oobfree[3] | oobfree[3] || oobfree[48] | oobfree[47] | |62 | oobfree[4] | oobfree[4] || oobfree[49] | oobfree[48] | |63 | oobfree[5] | oobfree[5] || oobfree[50] | oobfree[49] | +---+------------+-------------+--------------+-------------+
[1] ecc-layout expected by ROM code, as specified in SoC TRM under: Chapter="Initialization" Section="Device Initialization by ROM code" Sub-Section="Memory Booting" Heading="NAND" Figure="ECC Locations in NAND Spare Areas"
[2] ecc-layout updates in u-boot http://lists.denx.de/pipermail/u-boot/2013-November/167551.html
[3] u-boot configurations to match above ecc-layout are documented at https://processors.wiki.ti.com/index.php/Linux_Core_NAND_User%27s_Guide
CC: stable@vger.kernel.org # 3.13.x+ Reported-by: Enric Balletbo Serra eballetbo@iseebcn.com Tested-by: Enric Balletbo i Serra eballetbo@gmail.com Tested-by: Stefan Roese sr@denx.de Signed-off-by: Pekon Gupta pekon@ti.com --- drivers/mtd/nand/omap2.c | 31 +++++++++++++++++++++++-------- 1 file changed, 23 insertions(+), 8 deletions(-)
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index ef4190a..34ef941 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -1633,6 +1633,7 @@ static int omap_nand_probe(struct platform_device *pdev) int i; dma_cap_mask_t mask; unsigned sig; + unsigned oob_index; struct resource *res; struct mtd_part_parser_data ppdata = {};
@@ -1826,9 +1827,11 @@ static int omap_nand_probe(struct platform_device *pdev) (mtd->writesize / nand_chip->ecc.size); if (nand_chip->options & NAND_BUSWIDTH_16) - ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + oob_index = BADBLOCK_MARKER_LENGTH; else - ecclayout->eccpos[0] = 1; + oob_index = 1; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; ecclayout->oobfree->offset = ecclayout->eccpos[0] + ecclayout->eccbytes; break; @@ -1847,7 +1850,12 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->eccbytes = nand_chip->ecc.bytes * (mtd->writesize / nand_chip->ecc.size); - ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) { + ecclayout->eccpos[i] = oob_index; + if (((i + 1) % nand_chip->ecc.bytes) == 0) + oob_index++; + } ecclayout->oobfree->offset = ecclayout->eccpos[0] + ecclayout->eccbytes; /* software bch library is used for locating errors */ @@ -1883,7 +1891,9 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->eccbytes = nand_chip->ecc.bytes * (mtd->writesize / nand_chip->ecc.size); - ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; ecclayout->oobfree->offset = ecclayout->eccpos[0] + ecclayout->eccbytes; /* This ECC scheme requires ELM H/W block */ @@ -1913,7 +1923,12 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->eccbytes = nand_chip->ecc.bytes * (mtd->writesize / nand_chip->ecc.size); - ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) { + ecclayout->eccpos[i] = oob_index; + if (((i + 1) % nand_chip->ecc.bytes) == 0) + oob_index++; + } ecclayout->oobfree->offset = ecclayout->eccpos[0] + ecclayout->eccbytes; /* software bch library is used for locating errors */ @@ -1956,7 +1971,9 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->eccbytes = nand_chip->ecc.bytes * (mtd->writesize / nand_chip->ecc.size); - ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; ecclayout->oobfree->offset = ecclayout->eccpos[0] + ecclayout->eccbytes; break; @@ -1975,8 +1992,6 @@ static int omap_nand_probe(struct platform_device *pdev) /* populate remaining ECC layout data */ ecclayout->oobfree->length = mtd->oobsize - (BADBLOCK_MARKER_LENGTH + ecclayout->eccbytes); - for (i = 1; i < ecclayout->eccbytes; i++) - ecclayout->eccpos[i] = ecclayout->eccpos[0] + i; /* check if NAND device's OOB is enough to store ECC signatures */ if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) { pr_err("not enough OOB bytes required = %d, available=%d\n",