Add DT node and bindings documentation for FIMD.
Signed-off-by: Ajay Kumar ajaykumar.rs@samsung.com --- arch/arm/dts/exynos5250.dtsi | 6 ++ doc/device-tree-bindings/video/exynos-fb.txt | 92 ++++++++++++++++++++++++++++ 2 files changed, 98 insertions(+) create mode 100644 doc/device-tree-bindings/video/exynos-fb.txt
diff --git a/arch/arm/dts/exynos5250.dtsi b/arch/arm/dts/exynos5250.dtsi index ed8c8dd..3d8f747 100644 --- a/arch/arm/dts/exynos5250.dtsi +++ b/arch/arm/dts/exynos5250.dtsi @@ -151,4 +151,10 @@ }; };
+ fimd@14400000 { + compatible = "samsung,exynos-fimd"; + reg = <0x14400000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + }; }; diff --git a/doc/device-tree-bindings/video/exynos-fb.txt b/doc/device-tree-bindings/video/exynos-fb.txt new file mode 100644 index 0000000..bb7441c --- /dev/null +++ b/doc/device-tree-bindings/video/exynos-fb.txt @@ -0,0 +1,92 @@ +Exynos Display Controller +========================= +Required properties: +SOC specific: + compatible: should be "samsung,exynos-fimd" + reg: Base address of FIMD IP. + +Board(panel specific): + samsung,vl-col: X resolution of the panel + samsung,vl-row: Y resolution of the panel + samsung,vl-freq: Refresh rate + samsung,vl-bpix: Bits per pixel + samsung,vl-hspw: Hsync value + samsung,vl-hfpd: Right margin + samsung,vl-hbpd: Left margin + samsung,vl-vspw: Vsync value + samsung,vl-vfpd: Lower margin + samsung,vl-vbpd: Upper margin + +Optional properties: +Board(panel specific): + samsung,vl-width: width of display area in mm + samsung,vl-height: Height of display area in mm + + samsung,vl-clkp: Clock polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-oep: Output Enable polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-hsp: Horizontal Sync polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-vsp: Vertical Sync polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-dp: Data polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + + samsung,vl-cmd-allow-len: Wait end of frame + samsung,winid: Window number on which data is to be displayed + samsung,init-delay: Delay before LCD initialization starts + samsung,power-on-delay: Delay after LCD is powered on + samsung,reset-delay: Delay after LCD is reset + samsung,interface-mode: 1(FIMD_RGB_INTERFACE), 2(FIMD_CPU_INTERFACE) + samsung,mipi-enabled: 1 if you want to use MIPI, else 0 + samsung,dp-enabled: 1is you want to use DP, else 0 + samsung,cs-setup: cs_setup value in FIMD_CPU_INTERFACE mode. + samsung,wr-setup: wr_setup value in FIMD_CPU_INTERFACE mode. + samsung,wr-act: wr_act value in FIMD_CPU_INTERFACE mode. + samsung,wr-hold: wr_hold value in FIMD_CPU_INTERFACE mode. + samsung,logo-on: 1 if you want to use custom logo. + 0 if you want LCD console. + samsung,logo-width: pixel width of logo image. Valid if logo_on = 1 + samsung,logo-height: pixel height of logo image. Valid if logo_on = 1 + samsung,logo-addr: Address of logo image. Valid if logo_on = 1 + samsung,rgb-mode: 0(MODE_RGB_P), 1(MODE_BGR_P), + 2(MODE_RGB_S), 3(MODE_BGR_S) + samsung,pclk-name: parent clock identifier: 1(MPLL), 2(EPLL), 3(VPLL) + samsung,sclk-div: parent_clock/source_clock ratio + samsung,dual-lcd-enabled: 1 if you support two LCD, else 0 + +Example: +SOC specific part: + fimd@14400000 { + compatible = "samsung,exynos-fimd"; + reg = <0x14400000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + }; + +Board specific part: + fimd@14400000 { + samsung,vl-freq = <60>; + samsung,vl-col = <2560>; + samsung,vl-row = <1600>; + samsung,vl-width = <2560>; + samsung,vl-height = <1600>; + + samsung,vl-clkp; + samsung,vl-dp; + samsung,vl-bpix = <4>; + + samsung,vl-hspw = <32>; + samsung,vl-hbpd = <80>; + samsung,vl-hfpd = <48>; + samsung,vl-vspw = <6>; + samsung,vl-vbpd = <37>; + samsung,vl-vfpd = <3>; + samsung,vl-cmd-allow-len = <0xf>; + + samsung,winid = <3>; + samsung,interface-mode = <1>; + samsung,dp-enabled = <1>; + samsung,dual-lcd-enabled = <0>; + };