+include $(TOPDIR)/config.mk
+LIB = lib$(BOARD).a
+COBJS := r0p7785lc0011rl.o selfcheck.o rtl8169_mac.o +SOBJS := lowlevel_init.o
+$(LIB): $(COBJS) $(SOBJS)
- $(AR) crv $@ $(COBJS) $(SOBJS)
please use $(ARFLAGS) instead of 'crv'
+clean:
- rm -f $(SOBJS) $(OBJS)
+distclean: clean
- rm -f $(LIB) core *.bak .depend
pelase add the $(obj)
+#########################################################################
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@+-include .depend
- MA 02111-1307 USA
- */
+#define PCIREG_8(_adr) (*(volatile unsigned char *)(_adr)) +#define PCIREG_32(_adr) (*(volatile unsigned long *)(_adr)) +#define PCI_PAR PCIREG_32(0xfe0401c0) +#define PCI_PDR PCIREG_32(0xfe040220) +#define PCI_CR PCIREG_32(0xfe040100) +#define PCI_CONF1 PCIREG_32(0xfe040004)
+#define EEPROM_ADD 0x00000050 +#define HIGH 1 +#define LOW 0
+#define PCI_PROG 0x80
+#define PCI_EEP_ADDRESS (unsigned short)0x0007 +#define PCI_MAC_ADDRESS_SIZE 3
+#define TIME1 100 +#define TIME2 20000
+#define BIT_DUMMY 0 +#define MAC_EEP_READ 1 +#define MAC_EEP_WRITE 2 +#define MAC_EEP_ERACE 3 +#define MAC_EEP_EWEN 4 +#define MAC_EEP_EWDS 5
+#define DEBUG 0
Please remove Could you add few comment about the data?
+/* RTL8169 */ +const unsigned short EEPROM_W_Data_8169_A[] = {
- 0x8129, 0x10ec, 0x8169, 0x1154, 0x032b,
- 0x4020, 0xa101
+}; +const unsigned short EEPROM_W_Data_8169_B[] = {
- 0x4d15, 0xf7c2, 0x8000, 0x0000, 0x0000, 0x1300,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x2000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000
+};
+int do_set_mac(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{
- int i;
- unsigned char mac[6];
- char *s, *e;
- if (argc != 2) {
printf("Usage:\n%s\n", cmdtp->usage);return 1;- }
- s = argv[1];
- for (i = 0; i < 6; i++) {
mac[i] = s ? simple_strtoul(s, &e, 16) : 0;if (s)s = (*e) ? e + 1 : e;- }
- mac_write(mac);
- return 0;
+}
+U_BOOT_CMD(
- setmac, 2, 1, do_set_mac,
- "setmac - write MAC address for RTL8110SCL\n",
- "\n"
- "setmac <mac address> - write MAC address for RTL8110SCL\n"
+);
+int do_print_mac(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{
- int i;
- uchar mac[6];
- if (argc != 1) {
printf("Usage:\n%s\n", cmdtp->usage);return 1;- }
- mac_read();
- return 0;
+}
+U_BOOT_CMD(
- printmac, 1, 1, do_print_mac,
- "printmac - print MAC address for RTL8110\n",
- "\n"
- " - print MAC address for RTL8110\n"
+);
Could you add a README for this board and describe its specific command?
+U_BOOT_CMD(
- hwtest, 2, 1, do_hw_test,
- "hwtest - hardware test for R0P7785LC0011RL board\n",
- "\n"
- "hwtest all - test all hardware\n"
- "hwtest pld - output pld version\n"
- "hwtest led - test LED\n"
- "hwtest dipsw - test DIPSW\n"
- "hwtest sm107 - output SM107 version\n"
- "hwtest usb - test R8A66597\n"
- "hwtest i2c - output PCA9564 version\n"
- "hwtest net - compare RTL8110 ID\n"
- "hwtest sata - compare SiI3512 ID\n"
- "hwtest pci - output PCI slot device ID\n"
+);
idem
+
+#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_IPADDR 192.168.10.100 +#define CONFIG_SERVERIP 192.168.10.77 +#define CONFIG_GATEWAYIP 192.168.10.77
please remove this 4 defines
+#define __io +#define __mem_pci
is it really the good place to define it??
+#define CONFIG_PCI_MEM_BUS 0xFD000000 /* Memory space base addr */ +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x01000000 /* Size of Memory window */
Best Regards, J.