Hello
I have a question to this code (drivers/pci/pcie_layerscape.c):
void ls_pcie_atu_outbound_set(struct ls_pcie *pcie, int idx, int type, u64 phys, u64 bus_addr, u64 size) { dbi_writel(pcie, PCIE_ATU_REGION_OUTBOUND | idx, PCIE_ATU_VIEWPORT); dbi_writel(pcie, (u32)phys, PCIE_ATU_LOWER_BASE); dbi_writel(pcie, phys >> 32, PCIE_ATU_UPPER_BASE); dbi_writel(pcie, (u32)phys + size - 1, PCIE_ATU_LIMIT); dbi_writel(pcie, (u32)bus_addr, PCIE_ATU_LOWER_TARGET); dbi_writel(pcie, bus_addr >> 32, PCIE_ATU_UPPER_TARGET); dbi_writel(pcie, type, PCIE_ATU_CR1); dbi_writel(pcie, PCIE_ATU_ENABLE, PCIE_ATU_CR2); }
/* Use bar match mode and MEM type as default */ void ls_pcie_atu_inbound_set(struct ls_pcie *pcie, u32 pf, u32 vf_flag, int type, int idx, int bar, u64 phys) { dbi_writel(pcie, PCIE_ATU_REGION_INBOUND | idx, PCIE_ATU_VIEWPORT); dbi_writel(pcie, (u32)phys, PCIE_ATU_LOWER_TARGET); dbi_writel(pcie, phys >> 32, PCIE_ATU_UPPER_TARGET); dbi_writel(pcie, type | PCIE_ATU_FUNC_NUM(pf), PCIE_ATU_CR1); dbi_writel(pcie, PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE | (vf_flag ? PCIE_ATU_FUNC_NUM_MATCH_EN : 0) | (vf_flag ? PCIE_ATU_VFBAR_MATCH_MODE_EN : 0) | PCIE_ATU_BAR_NUM(bar), PCIE_ATU_CR2); }
void ls_pcie_dump_atu(struct ls_pcie *pcie, u32 win_num, u32 type) { int win_idx;
for (win_idx = 0; win_idx < win_num; win_idx++) { dbi_writel(pcie, type | win_idx, PCIE_ATU_VIEWPORT); debug("iATU%d:\n", win_idx); debug("\tLOWER PHYS 0x%08x\n", dbi_readl(pcie, PCIE_ATU_LOWER_BASE)); debug("\tUPPER PHYS 0x%08x\n", dbi_readl(pcie, PCIE_ATU_UPPER_BASE)); if (type == PCIE_ATU_REGION_OUTBOUND) { debug("\tLOWER BUS 0x%08x\n", dbi_readl(pcie, PCIE_ATU_LOWER_TARGET)); debug("\tUPPER BUS 0x%08x\n", dbi_readl(pcie, PCIE_ATU_UPPER_TARGET)); debug("\tLIMIT 0x%08x\n", dbi_readl(pcie, PCIE_ATU_LIMIT)); } debug("\tCR1 0x%08x\n", dbi_readl(pcie, PCIE_ATU_CR1)); debug("\tCR2 0x%08x\n", dbi_readl(pcie, PCIE_ATU_CR2)); } }
For outbound *_BASE and *_TARGET values are set. For inbound only *_TARGET values are set. However in dump it always prints the *_BASE values while the *_TARGET are only printed for outbound.
Shouldn't that be the other way around? Either I didn't understand ATUs or there's a mixup here.
Second question: We want to make an endpoint with 4 BARs. Is it possible to configure the internal addresses in the ATUs? The function ls_pcie_ep_setup_atu uses a configurable base address but then all ATUs are placed one after each other. How can I give them arbitrary addresses?
Thanks
bye Fabi