Adding the support for 2 boards sharing common code for Ocelot chip: PCB120 and PCB123
Signed-off-by: Gregory CLEMENT gregory.clement@bootlin.com --- MAINTAINERS | 5 + arch/mips/dts/mscc,ocelot.dtsi | 152 +++++++++++++++++++++++++++ arch/mips/dts/mscc,ocelot_pcb.dtsi | 42 ++++++++ arch/mips/dts/ocelot_pcb120.dts | 12 +++ arch/mips/dts/ocelot_pcb123.dts | 12 +++ arch/mips/mach-mscc/Kconfig | 2 + board/mscc/ocelot/Kconfig | 14 +++ board/mscc/ocelot/Makefile | 4 + board/mscc/ocelot/ocelot.c | 58 ++++++++++ configs/mscc_ocelot_defconfig | 73 +++++++++++++ configs/mscc_ocelot_pcb120_defconfig | 66 ++++++++++++ include/configs/vcoreiii.h | 82 +++++++++++++++ 12 files changed, 522 insertions(+) create mode 100644 arch/mips/dts/mscc,ocelot.dtsi create mode 100644 arch/mips/dts/mscc,ocelot_pcb.dtsi create mode 100644 arch/mips/dts/ocelot_pcb120.dts create mode 100644 arch/mips/dts/ocelot_pcb123.dts create mode 100644 board/mscc/ocelot/Kconfig create mode 100644 board/mscc/ocelot/Makefile create mode 100644 board/mscc/ocelot/ocelot.c create mode 100644 configs/mscc_ocelot_defconfig create mode 100644 configs/mscc_ocelot_pcb120_defconfig create mode 100644 include/configs/vcoreiii.h
diff --git a/MAINTAINERS b/MAINTAINERS index 53a3c5bec6..c906ca006b 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -490,6 +490,11 @@ M: Lars Povlsen lars.povlsen@microchip.com M: Horatiu Vultur horatiu.vultur@microchip.com S: Maintained F: arch/mips/mach-mscc/ +F: arch/mips/dts/mscc* +F: arch/mips/dts/ocelot* +F: board/mscc/ +F: configs/mscc* +F: include/configs/vcoreiii.h
MMC M: Jaehoon Chung jh80.chung@samsung.com diff --git a/arch/mips/dts/mscc,ocelot.dtsi b/arch/mips/dts/mscc,ocelot.dtsi new file mode 100644 index 0000000000..87b4736285 --- /dev/null +++ b/arch/mips/dts/mscc,ocelot.dtsi @@ -0,0 +1,152 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "mscc,ocelot"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "mips,mips24KEc"; + device_type = "cpu"; + clocks = <&cpu_clk>; + reg = <0>; + }; + }; + + aliases { + serial0 = &uart0; + }; + + cpuintc: interrupt-controller@0 { + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + compatible = "mti,cpu-interrupt-controller"; + }; + + cpu_clk: cpu-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <500000000>; + }; + + ahb_clk: ahb-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <250000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x70000000 0x2000000>; + + interrupt-parent = <&intc>; + + cpu_ctrl: syscon@0 { + compatible = "mscc,ocelot-cpu-syscon", "syscon"; + reg = <0x0 0x2c>; + }; + + intc: interrupt-controller@70 { + compatible = "mscc,ocelot-icpu-intr"; + reg = <0x70 0x70>; + #interrupt-cells = <1>; + interrupt-controller; + interrupt-parent = <&cpuintc>; + interrupts = <2>; + }; + + uart0: serial@100000 { + pinctrl-0 = <&uart_pins>; + pinctrl-names = "default"; + compatible = "ns16550a"; + reg = <0x100000 0x20>; + interrupts = <6>; + clocks = <&ahb_clk>; + reg-io-width = <4>; + reg-shift = <2>; + + status = "disabled"; + }; + + uart2: serial@100800 { + pinctrl-0 = <&uart2_pins>; + pinctrl-names = "default"; + compatible = "ns16550a"; + reg = <0x100800 0x20>; + interrupts = <7>; + clocks = <&ahb_clk>; + reg-io-width = <4>; + reg-shift = <2>; + + status = "disabled"; + }; + + spi0: spi-master@101000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-ssi"; + reg = <0x101000 0x40>; + num-chipselect = <4>; + bus-num = <0>; + reg-io-width = <4>; + reg-shift = <2>; + spi-max-frequency = <18000000>; /* input clock */ + clocks = <&ahb_clk>; + + status = "disabled"; + }; + + reset@1070008 { + compatible = "mscc,ocelot-chip-reset"; + reg = <0x1070008 0x4>; + }; + + gpio: pinctrl@1070034 { + compatible = "mscc,ocelot-pinctrl"; + reg = <0x1070034 0x68>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&gpio 0 0 22>; + + uart_pins: uart-pins { + pins = "GPIO_6", "GPIO_7"; + function = "uart"; + }; + + uart2_pins: uart2-pins { + pins = "GPIO_12", "GPIO_13"; + function = "uart2"; + }; + + spi_cs1_pin: spi-cs1-pin { + pins = "GPIO_8"; + function = "si"; + }; + + spi_cs2_pin: spi-cs2-pin { + pins = "GPIO_9"; + function = "si"; + }; + + spi_cs3_pin: spi-cs3-pin { + pins = "GPIO_16"; + function = "si"; + }; + + spi_cs4_pin: spi-cs4-pin { + pins = "GPIO_17"; + function = "si"; + }; + }; + }; +}; diff --git a/arch/mips/dts/mscc,ocelot_pcb.dtsi b/arch/mips/dts/mscc,ocelot_pcb.dtsi new file mode 100644 index 0000000000..90725d3b94 --- /dev/null +++ b/arch/mips/dts/mscc,ocelot_pcb.dtsi @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,ocelot.dtsi" + +/ { + compatible = "mscc,ocelot"; + + aliases { + spi0 = &spi0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + pinctrl-0 = <&spi_cs1_pin>; + pinctrl-names = "default"; + + spi-flash@0 { + compatible = "spi-flash"; + spi-max-frequency = <18000000>; /* input clock */ + reg = <0>; /* CS0 */ + }; + + spi-nand@1 { + compatible = "spi-nand"; + spi-max-frequency = <18000000>; /* input clock */ + reg = <1>; /* CS1 */ + }; +}; diff --git a/arch/mips/dts/ocelot_pcb120.dts b/arch/mips/dts/ocelot_pcb120.dts new file mode 100644 index 0000000000..47d305a614 --- /dev/null +++ b/arch/mips/dts/ocelot_pcb120.dts @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,ocelot_pcb.dtsi" + +/ { + model = "Ocelot PCB120 Reference Board"; + compatible = "mscc,ocelot-pcb120", "mscc,ocelot"; +}; diff --git a/arch/mips/dts/ocelot_pcb123.dts b/arch/mips/dts/ocelot_pcb123.dts new file mode 100644 index 0000000000..17d8d326ce --- /dev/null +++ b/arch/mips/dts/ocelot_pcb123.dts @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,ocelot_pcb.dtsi" + +/ { + model = "Ocelot PCB123 Reference Board"; + compatible = "mscc,ocelot-pcb123", "mscc,ocelot"; +}; diff --git a/arch/mips/mach-mscc/Kconfig b/arch/mips/mach-mscc/Kconfig index a8cace0e79..fc806fc1f3 100644 --- a/arch/mips/mach-mscc/Kconfig +++ b/arch/mips/mach-mscc/Kconfig @@ -79,4 +79,6 @@ config DDRTYPE_MT47H128M8HQ
endchoice
+source "board/mscc/ocelot/Kconfig" + endmenu diff --git a/board/mscc/ocelot/Kconfig b/board/mscc/ocelot/Kconfig new file mode 100644 index 0000000000..9ddc0880b1 --- /dev/null +++ b/board/mscc/ocelot/Kconfig @@ -0,0 +1,14 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +config SYS_VENDOR + default "mscc" + +if SOC_OCELOT + +config SYS_BOARD + default "ocelot" + +config SYS_CONFIG_NAME + default "ocelot" + +endif diff --git a/board/mscc/ocelot/Makefile b/board/mscc/ocelot/Makefile new file mode 100644 index 0000000000..9f28c81268 --- /dev/null +++ b/board/mscc/ocelot/Makefile @@ -0,0 +1,4 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +obj-$(CONFIG_SOC_OCELOT) := ocelot.o + diff --git a/board/mscc/ocelot/ocelot.c b/board/mscc/ocelot/ocelot.c new file mode 100644 index 0000000000..d521a61957 --- /dev/null +++ b/board/mscc/ocelot/ocelot.c @@ -0,0 +1,58 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/addrspace.h> +#include <asm/types.h> +#include <environment.h> +#include <spi.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define MSCC_GPIO_ALT0 0x54 +#define MSCC_GPIO_ALT1 0x58 + +void external_cs_manage(struct udevice *dev, bool enable) +{ + u32 cs = spi_chip_select(dev); + /* IF_SI0_OWNER, select the owner of the SI interface + * Encoding: 0: SI Slave + * 1: SI Boot Master + * 2: SI Master Controller + */ + if (!enable) { + writel(ICPU_SW_MODE_SW_PIN_CTRL_MODE | + ICPU_SW_MODE_SW_SPI_CS(BIT(cs)), BASE_CFG + ICPU_SW_MODE); + clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL, + ICPU_GENERAL_CTRL_IF_SI_OWNER_M, + ICPU_GENERAL_CTRL_IF_SI_OWNER(2)); + } else { + writel(0, BASE_CFG + ICPU_SW_MODE); + clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL, + ICPU_GENERAL_CTRL_IF_SI_OWNER_M, + ICPU_GENERAL_CTRL_IF_SI_OWNER(1)); + } +} + +void board_debug_uart_init(void) +{ + /* too early for the pinctrl driver, so configure the UART pins here */ + setbits_le32(BASE_DEVCPU_GCB + MSCC_GPIO_ALT0, BIT(6) | BIT(7)); + clrbits_le32(BASE_DEVCPU_GCB + MSCC_GPIO_ALT1, BIT(6) | BIT(7)); +} + +int board_early_init_r(void) +{ + /* Prepare SPI controller to be used in master mode */ + writel(0, BASE_CFG + ICPU_SW_MODE); + clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL, + ICPU_GENERAL_CTRL_IF_SI_OWNER_M, + ICPU_GENERAL_CTRL_IF_SI_OWNER(2)); + + /* Address of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE; + return 0; +} diff --git a/configs/mscc_ocelot_defconfig b/configs/mscc_ocelot_defconfig new file mode 100644 index 0000000000..6de047a8de --- /dev/null +++ b/configs/mscc_ocelot_defconfig @@ -0,0 +1,73 @@ +CONFIG_MIPS=y +CONFIG_SYS_TEXT_BASE=0x40000000 +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DEBUG_UART_BOARD_INIT=y +CONFIG_DEBUG_UART_BASE=0x70100000 +CONFIG_DEBUG_UART_CLOCK=250000000 +CONFIG_ARCH_MSCC=y +CONFIG_TARGET_OCELOT_PCB123=y +CONFIG_SYS_LITTLE_ENDIAN=y +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200" +CONFIG_LOGLEVEL=7 +CONFIG_DISPLAY_CPUINFO=y +CONFIG_SYS_PROMPT="pcb123 # " +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_CONSOLE is not set +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_MD5SUM=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_MTD=y +CONFIG_CMD_UBI=y +# CONFIG_CMD_UBIFS is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_DHCP=y +# CONFIG_NET_TFTP_VARS is not set +# CONFIG_CMD_NFS is not set +CONFIG_CMD_PING=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi_flash" +CONFIG_MTDPARTS_DEFAULT="mtdparts=spi_flash:512k(UBoot),256k(Env),256k(conf),15m(linux),15m(linux.bk)" +# CONFIG_ISO_PARTITION is not set +CONFIG_OF_EMBED=y +CONFIG_DEFAULT_DEVICE_TREE="ocelot_pcb123" +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_CLK=y +CONFIG_DM_GPIO=y +CONFIG_MTD_PARTITIONS=y +CONFIG_MTD=y +CONFIG_MTD_NAND_CORE=y +CONFIG_MTD_SPI_NAND=y +CONFIG_MTD_UBI=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_GIGADEVICE=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_DM_ETH=y +CONFIG_PINCTRL=y +CONFIG_PINCONF=y +CONFIG_DM_SERIAL=y +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_SYS_NS16550=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_SPI_MEM=y +CONFIG_DESIGNWARE_SPI=y +CONFIG_LZMA=y diff --git a/configs/mscc_ocelot_pcb120_defconfig b/configs/mscc_ocelot_pcb120_defconfig new file mode 100644 index 0000000000..3ba7ea91f9 --- /dev/null +++ b/configs/mscc_ocelot_pcb120_defconfig @@ -0,0 +1,66 @@ +CONFIG_MIPS=y +CONFIG_SYS_TEXT_BASE=0x40000000 +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_ARCH_MSCC=y +CONFIG_SYS_LITTLE_ENDIAN=y +CONFIG_DEFAULT_DEVICE_TREE="ocelot_pcb120" +CONFIG_FIT=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200" +CONFIG_LOGLEVEL=7 +CONFIG_DISPLAY_CPUINFO=y +CONFIG_SYS_PROMPT="pcb120 # " +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_CONSOLE is not set +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_MD5SUM=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_MTD=y +CONFIG_CMD_UBI=y +# CONFIG_CMD_UBIFS is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_DHCP=y +# CONFIG_NET_TFTP_VARS is not set +# CONFIG_CMD_NFS is not set +CONFIG_CMD_PING=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi_flash" +CONFIG_MTDPARTS_DEFAULT="mtdparts=spi_flash:512k(UBoot),256k(Env),256k(conf),15m(linux),15m(linux.bk)" +# CONFIG_ISO_PARTITION is not set +CONFIG_OF_EMBED=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_CLK=y +CONFIG_DM_GPIO=y +CONFIG_MTD_PARTITIONS=y +CONFIG_MTD=y +CONFIG_MTD_NAND_CORE=y +CONFIG_MTD_SPI_NAND=y +CONFIG_MTD_UBI=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_GIGADEVICE=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_DM_ETH=y +CONFIG_PINCTRL=y +CONFIG_PINCONF=y +CONFIG_DM_SERIAL=y +CONFIG_SYS_NS16550=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_SPI_MEM=y +CONFIG_DESIGNWARE_SPI=y +CONFIG_LZMA=y diff --git a/include/configs/vcoreiii.h b/include/configs/vcoreiii.h new file mode 100644 index 0000000000..df89cdaebf --- /dev/null +++ b/include/configs/vcoreiii.h @@ -0,0 +1,82 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef __VCOREIII_H +#define __VCOREIII_H + +#include <linux/sizes.h> + +/* Onboard devices */ + +#define CONFIG_SYS_MALLOC_LEN 0x100000 +#define CONFIG_SYS_LOAD_ADDR 0x00100000 +#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 + +#define CPU_CLOCK_RATE 500000000 /* Clock for the MIPS core */ +#ifdef CONFIG_SOC_LUTON +#define CONFIG_SYS_MIPS_TIMER_FREQ 208333333 +#else +#define CONFIG_SYS_MIPS_TIMER_FREQ (CPU_CLOCK_RATE / 2) +#endif +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_MIPS_TIMER_FREQ + +#if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_OFFSET) +#define CONFIG_ENV_OFFSET (1024 * 1024) +#define CONFIG_ENV_SIZE (256 * 1024) +#define CONFIG_ENV_SECT_SIZE (256 * 1024) + +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) + +#define CONFIG_ENV_SPI_MAX_HZ 0 /* This force to read from DT */ +#define CONFIG_ENV_SPI_MODE 0 /* This force to read from DT */ +#endif + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#if defined(CONFIG_DDRTYPE_H5TQ1G63BFA) || defined(CONFIG_DDRTYPE_MT47H128M8HQ) +#define CONFIG_SYS_SDRAM_SIZE (128 * SZ_1M) +#elif defined(CONFIG_DDRTYPE_MT41J128M16HA) || defined(CONFIG_DDRTYPE_MT41K128M16JT) +#define CONFIG_SYS_SDRAM_SIZE (256 * SZ_1M) +#elif defined(CONFIG_DDRTYPE_H5TQ4G63MFR) || defined(CONFIG_DDRTYPE_MT41K256M16) +#define CONFIG_SYS_SDRAM_SIZE (512 * SZ_1M) +#else +#error Unknown DDR size - please add! +#endif + +#define CONFIG_CONS_INDEX 1 + +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_SDRAM_SIZE - SZ_1M) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_BOARD_EARLY_INIT_R +#if defined(CONFIG_MTDIDS_DEFAULT) && defined(CONFIG_MTDPARTS_DEFAULT) +#define VCOREIII_DEFAULT_MTD_ENV \ + "mtdparts="CONFIG_MTDPARTS_DEFAULT"\0" \ + "mtdids="CONFIG_MTDIDS_DEFAULT"\0" +#else +#define VCOREIII_DEFAULT_MTD_ENV /* Go away */ +#endif + +#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + VCOREIII_DEFAULT_MTD_ENV \ + "loadaddr=0x81000000\0" \ + "spi_image_off=0x00100000\0" \ + "console=ttyS0,115200\0" \ + "setup=setenv bootargs console=${console} ${mtdparts}" \ + "${bootargs_extra}\0" \ + "spiboot=run setup; sf probe; sf read ${loadaddr}" \ + "${spi_image_off} 0x600000; bootm ${loadaddr}\0" \ + "ubootfile=u-boot.bin\0" \ + "update=sf probe;mtdparts;dhcp ${loadaddr} ${ubootfile};" \ + "sf erase UBoot 0x100000;" \ + "sf write ${loadaddr} UBoot ${filesize}\0" \ + "bootcmd=run spiboot\0" \ + "" +#endif /* __VCOREIII_H */