This is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass sjg@chromium.org ---
include/configs/manroland/common.h | 106 --------------- include/configs/manroland/mpc5200-common.h | 205 ----------------------------- 2 files changed, 311 deletions(-) delete mode 100644 include/configs/manroland/common.h delete mode 100644 include/configs/manroland/mpc5200-common.h
diff --git a/include/configs/manroland/common.h b/include/configs/manroland/common.h deleted file mode 100644 index 7d63e14030..0000000000 --- a/include/configs/manroland/common.h +++ /dev/null @@ -1,106 +0,0 @@ -/* - * (C) Copyright 2009 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __MANROLAND_COMMON_H -#define __MANROLAND_COMMON_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_BOARD_EARLY_INIT_R - -/* - * Command line configuration. - */ -#define CONFIG_CMD_DATE -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DTT -#define CONFIG_CMD_IDE - -/* - * 8-symbol LED display (can be accessed with 'display' command) - */ -#define CONFIG_PDSP188x - -#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ - -/* - * Autobooting - */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addwdt=setenv bootargs ${bootargs} wdt=off\0" \ - "logval=4\0" \ - "addlog=setenv bootargs ${bootargs} loglevel=${logval}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "kernel_addr=ff810000\0" \ - "fdt_addr="__stringify(CONFIG_SYS_FLASH_BASE)"\0" \ - "flash_nfs=run nfsargs addip addcon addwdt addlog;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "kernel_addr_r=300000\0" \ - "fdt_addr_r=200000\0" \ - "fdt_file=" __stringify(CONFIG_HOSTNAME) "/" \ - __stringify(CONFIG_HOSTNAME) ".dtb\0" \ - "kernel_file=" __stringify(CONFIG_HOSTNAME) "/uImage \0" \ - "load_fdt=tftp ${fdt_addr_r} ${fdt_file};\0" \ - "load_kernel=tftp ${kernel_addr_r} ${kernel_file};\0" \ - "addcon=setenv bootargs ${bootargs} console=ttyPSC0,${baudrate}\0"\ - "net_nfs=run load_fdt load_kernel; " \ - "run nfsargs addip addcon addwdt addlog;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin \0" \ - "u-boot_addr_r=200000\0" \ - "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ - "update=protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +${filesize};"\ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +${filesize};"\ - "cp.b ${u-boot_addr_r} " __stringify(CONFIG_SYS_TEXT_BASE) \ - " ${filesize};" \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +${filesize}\0"\ - "" - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#define CONFIG_MISC_INIT_R 1 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ - -/* Enable an alternate, more extensive memory test */ -#define CONFIG_SYS_ALT_MEMTEST - -/* - * Enable loopw command. - */ - -#endif /* __MANROLAND_COMMON_H */ diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h deleted file mode 100644 index 60e8716a79..0000000000 --- a/include/configs/manroland/mpc5200-common.h +++ /dev/null @@ -1,205 +0,0 @@ -/* - * (C) Copyright 2009 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __MANROLAND_MPC52XX__COMMON_H -#define __MANROLAND_MPC52XX__COMMON_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC5200 1 /* MPC5200 CPU */ - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\ - 230400 } - -#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* - * RTC configuration - */ -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM81 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xFF800000 - -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ - -#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/ - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_CFI_AMD_RESET - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x4000 -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */ -#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */ - -/* Settings for XLB = 132 MHz */ -#define SDRAM_DDR 1 -#define SDRAM_MODE 0x018D0000 -#define SDRAM_EMODE 0x40090000 -#define SDRAM_CONTROL 0x714f0f00 -#define SDRAM_CONFIG1 0x73722930 -#define SDRAM_CONFIG2 0x47770000 -#define SDRAM_TAPDELAY 0x10000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) -#define CONFIG_SYS_MALLOC_LEN (512 << 10) -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_MII 1 - -/*use Hardware WDT */ -#define CONFIG_HW_WATCHDOG - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value*/ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -/* 8Mbit SRAM @0x80100000 */ -#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ - -#define CONFIG_IDE_PREINIT 1 - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#define CONFIG_ATAPI 1 - -#define OF_CPU "PowerPC,5200@0" -#define OF_SOC "soc5200@f0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" -#define CONFIG_OF_IDE_FIXUP - -#endif /* __MANROLAND_MPC52XX__COMMON_H */