This patch configures and initializes the L2 switch on T1040QDS board. The L2 switch ports must be initialized according to the SerDes protocols.
Signed-off-by: Codrin Ciubotariu codrin.ciubotariu@freescale.com Change-Id: I329f9cc1b1be745da23151e78831d8a3219b7f97 --- board/freescale/t1040qds/eth.c | 93 ++++++++++++++++++++++++++++++++++++++++++ include/configs/T1040QDS.h | 4 ++ 2 files changed, 97 insertions(+)
diff --git a/board/freescale/t1040qds/eth.c b/board/freescale/t1040qds/eth.c index 2f8e753..ba6f518 100644 --- a/board/freescale/t1040qds/eth.c +++ b/board/freescale/t1040qds/eth.c @@ -18,6 +18,9 @@ #include <fsl_mdio.h> #include <malloc.h> #include <asm/fsl_dtsec.h> +#ifdef CONFIG_VSC9953 +#include <vsc9953.h> +#endif
#include "../common/fman.h" #include "../common/qixis.h" @@ -439,6 +442,12 @@ int board_eth_init(bd_t *bis) #ifdef CONFIG_FMAN_ENET struct memac_mdio_info memac_mdio_info; unsigned int i; +#ifdef CONFIG_VSC9953 + int lane; + int phy_addr; + phy_interface_t phy_int; + struct mii_dev *bus; +#endif
printf("Initializing Fman\n"); set_brdcfg9_for_gtx_clk(); @@ -493,6 +502,90 @@ int board_eth_init(bd_t *bis) } }
+#ifdef CONFIG_VSC9953 + for (i = 0; i < VSC9953_MAX_PORTS; i++) { + lane = -1; + phy_addr = 0; + phy_int = PHY_INTERFACE_MODE_NONE; + switch (i) { + case 0: + case 1: + case 2: + case 3: + lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_A); + /* PHYs connected over QSGMII */ + if (lane >= 0) { + phy_addr = CONFIG_SYS_FM1_QSGMII21_PHY_ADDR + + i; + phy_int = PHY_INTERFACE_MODE_QSGMII; + break; + } + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_SW1_MAC1 + i); + + if (lane < 0) + break; + + /* PHYs connected over QSGMII */ + if (i != 3 || lane_to_slot[lane] == 7) + phy_addr = CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR + + i; + else + phy_addr = CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR; + phy_int = PHY_INTERFACE_MODE_SGMII; + break; + case 4: + case 5: + case 6: + case 7: + lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_B); + /* PHYs connected over QSGMII */ + if (lane >= 0) { + phy_addr = CONFIG_SYS_FM1_QSGMII11_PHY_ADDR + + i - 4; + phy_int = PHY_INTERFACE_MODE_QSGMII; + break; + } + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_SW1_MAC1 + i); + /* PHYs connected over SGMII */ + if (lane >= 0) { + phy_addr = CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR + + i - 3; + phy_int = PHY_INTERFACE_MODE_SGMII; + } + break; + case 8: + if (serdes_get_first_lane(FSL_SRDS_1, + SGMII_FM1_DTSEC1) < 0) + /* FM1@DTSEC1 is connected to SW1@PORT8 */ + vsc9953_port_enable(i); + break; + case 9: + if (serdes_get_first_lane(FSL_SRDS_1, + SGMII_FM1_DTSEC2) < 0) { + /* Enable L2 On MAC2 using SCFG */ + struct ccsr_scfg *scfg = (struct ccsr_scfg *) + CONFIG_SYS_MPC85xx_SCFG; + + out_be32(&scfg->esgmiiselcr, + in_be32(&scfg->esgmiiselcr) | + (0x80000000)); + vsc9953_port_enable(i); + } + break; + } + + if (lane >= 0) { + bus = mii_dev_for_muxval(lane_to_slot[lane]); + vsc9953_port_info_set_mdio(i, bus); + vsc9953_port_enable(i); + } + vsc9953_port_info_set_phy_address(i, phy_addr); + vsc9953_port_info_set_phy_int(i, phy_int); + } + +#endif cpu_eth_init(bis); #endif
diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index b70bdfe..5b7c3c4 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -689,6 +689,10 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ #endif
+#define CONFIG_VSC9953_CMD +#define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR 0x14 +#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x18 + /* * Dynamic MTD Partition support with mtdparts */