Hello York,
This fixes the crash on LS1088 sd-boot.
Regards Ashish
-----Original Message----- From: York Sun Sent: Friday, February 16, 2018 9:21 PM To: Ashish Kumar ashish.kumar@nxp.com; u-boot@lists.denx.de Cc: Pankit Garg pankit.garg@nxp.com; Maxime Ripard maxime.ripard@bootlin.com Subject: Re: Crash observed while running U-Boot on LS1088 SD-boot
Ashish,
Please check if this fixes it https://patchwork.ozlabs.org/patch/870653/
York
On 02/16/2018 02:57 AM, Ashish Kumar wrote:
Hello all,
I am seeing u-boot crash, while I run the latest u-boot on LS1088 for SD-
Boot(ls1088aqds_sdcard_qspi_defconfig).
There were some changes related to passing env-parameters introduced by
commit
"8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional
parameters to the env lookup function".
Did anyone face similar issue? I reached this commit("8a3a7e22") after running git bisect.
Log embedded in below mail chain.
Regards Ashish
-----Original Message----- From: Ashish Kumar Sent: Thursday, February 8, 2018 3:51 PM To: Maxime Ripard maxime.ripard@bootlin.com; York Sun york.sun@nxp.com Cc: Pankit Garg pankit.garg@nxp.com Subject: RE: Crash observed while running Uboot
Hello York, Maxime,
I am seeing this u-boot crash on top of the tree of denx.de. After running git bisect, I found this commit "8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional " introduces it. Any idea how to fix?
Logs below: U-Boot 2018.03-rc1-00185-g9b2cfe2 (Feb 08 2018 - 15:45:34 +0530)
SoC: LS1088AE Rev1.0 (0x87030010) Clock Configuration: CPU0(A53):1600 MHz CPU1(A53):1600 MHz CPU2(A53):1600 MHz CPU3(A53):1600 MHz CPU4(A53):1600 MHz CPU5(A53):1600 MHz CPU6(A53):1600 MHz CPU7(A53):1600 MHz Bus: 700 MHz DDR: 2100 MT/s Reset Configuration Word (RCW): 00000000: 4000541c 00000040 00000000 00000000 00000010: 00000000 000a0000 00300000 00000000 00000020: 01001150 00002580 00000000 00000040 00000030: 00000c5b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00000011 000009e7 00000070: 44110000 00009555 I2C: ready DRAM: Initializing DDR....using SPD Detected UDIMM 18ASF1G72AZ-2G1A1 7.9 GiB DDR 7.9 GiB (DDR4, 64-bit, CL=15, ECC on) FSL_SDHC: 0 SEC Firmware: config-1: no such config SEC Firmware: error (-2) SEC Firmware: Failed to load image WARN: pls set popts->cpo_sample = 0x6a in <board>/ddr.c to optimize cpo Waking secondary cores to start from fbd51000 All (8) cores are up. Using SERDES1 Protocol: 29 (0x1d) Using SERDES2 Protocol: 13 (0xd) NAND: 0 MiB MMC: Loading Environment from MMC... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial Model: NXP Layerscape 1088a QDS Board Board: LS1088A-QDS, Board Arch: V1, Board version: B, boot from SD card vBank: 0 FPGA: v6 (LS1088AQDS_2016_0818_1311), build 75 on Thu Aug 18 18:11:20 2016 SERDES1 Reference : Clock1 = 100MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Found 0 device(s). SCSI: Net: qds: WRIOP: Supported SerDes1 Protocol 0x1d PCIe0: pcie@3400000 Root Complex: no link PCIe1: pcie@3500000 Root Complex: no link PCIe2: pcie@3600000 Root Complex: x1 gen1 e1000: 00:1b:21:39:30:86 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - fe:89:69:1c:38:4f , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 96:82:07:2f:7f:b0 , DPMAC3@qsgmii Warning: DPMAC3@qsgmii (eth2) using random MAC address - 92:ba:99:eb:1b:fd , DPMAC4@qsgmii Warning: DPMAC4@qsgmii (eth3) using random MAC address - fa:b1:f7:d8:5c:02 , DPMAC5@qsgmii Warning: DPMAC5@qsgmii (eth4) using random MAC address - c2:ea:0a:78:b5:0a , DPMAC6@qsgmii Warning: DPMAC6@qsgmii (eth5) using random MAC address - ca:e2:23:02:39:06 , DPMAC7@qsgmii Warning: DPMAC7@qsgmii (eth6) using random MAC address - 92:1f:76:1e:82:97 , DPMAC8@qsgmii Warning: DPMAC8@qsgmii (eth7) using random MAC address - 9a:17:5f:64:0e:9b , DPMAC9@qsgmii Warning: DPMAC9@qsgmii (eth8) using random MAC address - a2:4c:a2:c4:e7:93 , DPMAC10@qsgmii Warning: DPMAC10@qsgmii (eth9) using random MAC address - aa:44:8b:be:6b:9f , e1000#0 [PRIME] Device: FSL_SDHC Manufacturer ID: 74 OEM: 4a45 Name: SDC Bus Speed: 50000000 Mode : SD High Speed (50MHz) card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed (50MHz)] host capabilities: widths [8, 4, 1] modes [MMC legacy, SD Legacy, MMC High Speed (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)] Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 3.7 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 20480, count 2048 ... 2048 blocks read: OK
MMC read: dev # 0, block # 28672, count 2048 ... 2048 blocks read: OK crc32+ "Synchronous Abort" handler, esr 0x96000045 ELR: 80462fac LR: 8043cde8 x0 : 0000008240000000 x1 : 00000000800000c8 x2 : 00000000000d0f68 x3 : 0000000000000000 x4 : 000000000001a1ed x5 : 00000000000d0f68 x6 : 60c7847000e08070 x7 : 0000000000000003 x8 : 0000000000000084 x9 : 000000000000000c x10: 00000000fbb4ab5c x11: 0000000080000000 x12: 000000000000005b x13: 00000000000d1080 x14: 00000000fbb4ab7c x15: 0000000080000000 x16: 00000000fbdbf35f x17: 00000000fbdcf7e5 x18: 00000000fbb4cd88 x19: 0000008240000000 x20: 00000000000d0f68 x21: 0000000000000007 x22: 0000000080100000 x23: 00000000fbde5e54 x24: 0000000000000005 x25: 0000000000000000 x26: 0000000000000000 x27: 0000000000000000 x28: 00000000fbb57520 x29: 00000000fbb4ac40
-----Original Message----- From: Pankit Garg Sent: Tuesday, February 6, 2018 11:03 AM To: Maxime Ripard maxime.ripard@bootlin.com Cc: Ashish Kumar ashish.kumar@nxp.com Subject: RE: Crash observed while running Uboot
Hi Maxime Ripard,
We are using ls1088aqds_sdcard_qspi_defconfig. When we are trying to read from mmc we are getting this error.
Best Regards, Pankit Garg.
-----Original Message----- From: Maxime Ripard [mailto:maxime.ripard@bootlin.com] Sent: Monday, February 5, 2018 7:24 PM To: Pankit Garg pankit.garg@nxp.com Cc: Ashish Kumar ashish.kumar@nxp.com Subject: Re: Crash observed while running Uboot
Hi Pankit,
On Mon, Feb 05, 2018 at 01:07:48PM +0000, Pankit Garg wrote:
I am getting crash while running Uboot(cloned code from Upstream Repo) on LS1088aqds board .
I ran git bisect and find below commit id as Bad patch.
8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional
parameters to
the env lookup function
Any idea ,what is going wrong or how I can proceed further ?
Which configuration are you using?
Thanks! Maxime
-- Maxime Ripard, Bootlin (formerly Free Electrons) Embedded Linux and Kernel engineering http://bootlin.com