Enable support for I2C EEPROM driver on supported Renesas R-Car Gen3 boards. This is useful for accessing the board ID EEPROM.
Signed-off-by: Marek Vasut marek.vasut+renesas@gmail.com --- configs/r8a77990_ebisu_defconfig | 7 +++++++ configs/rcar3_salvator-x_defconfig | 7 +++++++ configs/rcar3_ulcb_defconfig | 7 +++++++ 3 files changed, 21 insertions(+)
diff --git a/configs/r8a77990_ebisu_defconfig b/configs/r8a77990_ebisu_defconfig index 15743c1a81..13ca814cbc 100644 --- a/configs/r8a77990_ebisu_defconfig +++ b/configs/r8a77990_ebisu_defconfig @@ -50,6 +50,13 @@ CONFIG_DFU_SF=y CONFIG_RCAR_GPIO=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_RCAR_IIC=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x70 +CONFIG_SYS_I2C_EEPROM_BUS=7 +CONFIG_SYS_EEPROM_SIZE=128 +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=7 +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=10 CONFIG_MMC_IO_VOLTAGE=y CONFIG_MMC_UHS_SUPPORT=y CONFIG_MMC_HS400_SUPPORT=y diff --git a/configs/rcar3_salvator-x_defconfig b/configs/rcar3_salvator-x_defconfig index efd6ca2da8..ef9775abfa 100644 --- a/configs/rcar3_salvator-x_defconfig +++ b/configs/rcar3_salvator-x_defconfig @@ -52,6 +52,13 @@ CONFIG_DFU_SF=y CONFIG_RCAR_GPIO=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_RCAR_IIC=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x70 +CONFIG_SYS_I2C_EEPROM_BUS=7 +CONFIG_SYS_EEPROM_SIZE=128 +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=7 +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=10 CONFIG_MMC_IO_VOLTAGE=y CONFIG_MMC_UHS_SUPPORT=y CONFIG_MMC_HS400_SUPPORT=y diff --git a/configs/rcar3_ulcb_defconfig b/configs/rcar3_ulcb_defconfig index a857e5bd1c..cfec485ec7 100644 --- a/configs/rcar3_ulcb_defconfig +++ b/configs/rcar3_ulcb_defconfig @@ -52,6 +52,13 @@ CONFIG_DFU_SF=y CONFIG_RCAR_GPIO=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_RCAR_IIC=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x70 +CONFIG_SYS_I2C_EEPROM_BUS=7 +CONFIG_SYS_EEPROM_SIZE=128 +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=7 +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=10 CONFIG_MMC_IO_VOLTAGE=y CONFIG_MMC_UHS_SUPPORT=y CONFIG_MMC_HS400_SUPPORT=y