Signed-off-by: Albert Aribaud albert.aribaud@free.fr --- This patch set introduces CONFIG_IDE_SWAP_IO as suggested by Wolfgang Denk, adds orion5x support to cmd_ide.c and adds IDE support to edminiv2.
Patchset history:
V1: Initial 4-patch set -- not cleanly submitted (does not appear on gmane for instance) and contained some unrelated changes.
V2: Slimmed down to 3 patches and removed unrelated changes.
arch/powerpc/include/asm/config.h | 3 +++ common/cmd_ide.c | 18 +++++++++--------- doc/README.PXA_CF | 8 ++++++++ include/configs/ap325rxa.h | 1 + include/configs/ms7720se.h | 1 + include/configs/r2dplus.h | 1 + include/configs/r7780mp.h | 1 + 7 files changed, 24 insertions(+), 9 deletions(-)
diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h index fc3facb..371989d 100644 --- a/arch/powerpc/include/asm/config.h +++ b/arch/powerpc/include/asm/config.h @@ -76,4 +76,7 @@ /* Relocation to SDRAM works on all PPC boards */ #define CONFIG_RELOC_FIXUP_WORKS
+/* All PPC boards must swap IDE bytes */ +#define CONFIG_IDE_SWAP_IO + #endif /* _ASM_CONFIG_H_ */ diff --git a/common/cmd_ide.c b/common/cmd_ide.c index d486697..9292a5b 100644 --- a/common/cmd_ide.c +++ b/common/cmd_ide.c @@ -853,7 +853,7 @@ input_swap_data(int dev, ulong *sect_buf, int words) #endif /* __LITTLE_ENDIAN || CONFIG_AU1X00 */
-#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA) || defined(CONFIG_SH) +#if defined(CONFIG_IDE_SWAP_IO) static void output_data(int dev, ulong *sect_buf, int words) { @@ -897,15 +897,15 @@ output_data(int dev, ulong *sect_buf, int words) } #endif } -#else /* ! __PPC__ */ +#else /* ! CONFIG_IDE_SWAP_IO */ static void output_data(int dev, ulong *sect_buf, int words) { outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words<<1); } -#endif /* __PPC__ */ +#endif /* CONFIG_IDE_SWAP_IO */
-#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA) || defined(CONFIG_SH) +#if defined(CONFIG_IDE_SWAP_IO) static void input_data(int dev, ulong *sect_buf, int words) { @@ -955,14 +955,14 @@ input_data(int dev, ulong *sect_buf, int words) } #endif } -#else /* ! __PPC__ */ +#else /* ! CONFIG_IDE_SWAP_IO */ static void input_data(int dev, ulong *sect_buf, int words) { insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words << 1); }
-#endif /* __PPC__ */ +#endif /* CONFIG_IDE_SWAP_IO */
/* ------------------------------------------------------------------------- */ @@ -1579,7 +1579,7 @@ int ide_device_present(int dev) * ATAPI Support */
-#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA) +#if defined(CONFIG_IDE_SWAP_IO) /* since ATAPI may use commands with not 4 bytes alligned length * we have our own transfer functions, 2 bytes alligned */ static void @@ -1646,7 +1646,7 @@ input_data_shorts(int dev, ushort *sect_buf, int shorts) #endif }
-#else /* ! __PPC__ */ +#else /* ! CONFIG_IDE_SWAP_IO */ static void output_data_shorts(int dev, ushort *sect_buf, int shorts) { @@ -1659,7 +1659,7 @@ input_data_shorts(int dev, ushort *sect_buf, int shorts) insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, shorts); }
-#endif /* __PPC__ */ +#endif /* CONFIG_IDE_SWAP_IO */
/* * Wait until (Status & mask) == res, or timeout (in ms) diff --git a/doc/README.PXA_CF b/doc/README.PXA_CF index 6a0f236..1d76b32 100644 --- a/doc/README.PXA_CF +++ b/doc/README.PXA_CF @@ -6,6 +6,14 @@ follow the connections of the standard lubbock. Anyway just the block marked memory configuration should be touched since the other parameters are imposed by the PXA architecture.
+EDIT 2010-07-01: in common/cmd_ide.c, having CONFIG_PXA_PCMCIA defined +would cause looping on inw()/outw() rather than using insw()/outsw(), +thus making sure IDE / ATA bytes are properly swapped. This behaviour +is now controlled by CONFIG_IDE_SWAP_IO, therefore PXA boards with +PCMCIA should #define CONFIG_IDE_SWAP_IO. + +#define CONFIG_IDE_SWAP_IO + #define CONFIG_PXA_PCMCIA 1 #define CONFIG_PXA_IDE 1
diff --git a/include/configs/ap325rxa.h b/include/configs/ap325rxa.h index 70dd47e..80a5797 100644 --- a/include/configs/ap325rxa.h +++ b/include/configs/ap325rxa.h @@ -138,6 +138,7 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0x200 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0x200 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x210 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO
/* if you use all NOR Flash , you change dip-switch. Please see Manual. */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 diff --git a/include/configs/ms7720se.h b/include/configs/ms7720se.h index ba0a3f8..0ea3527 100644 --- a/include/configs/ms7720se.h +++ b/include/configs/ms7720se.h @@ -122,5 +122,6 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO
#endif /* __MS7720SE_H */ diff --git a/include/configs/r2dplus.h b/include/configs/r2dplus.h index 8931b97..955f3ff 100644 --- a/include/configs/r2dplus.h +++ b/include/configs/r2dplus.h @@ -96,6 +96,7 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0x1000 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0x1000 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x800 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO
/* * SuperH PCI Bridge Configration diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h index 71c570e..3afe93a 100644 --- a/include/configs/r7780mp.h +++ b/include/configs/r7780mp.h @@ -171,6 +171,7 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0x1000 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0x1000 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x800 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO #endif /* CONFIG_CMD_IDE */
#endif /* __R7780RP_H */