Re: [PATCH 2/3] arm: kirkwood: Dreamplug: Use Ethernet PHY name and address from device tree

On 26.07.21 08:01, Tony Dinh wrote:

In DM Ethernet, the old "egiga0" and 'egiga1" names are no longer valid, so replace these with Ethernet PHY names from device tree. Also, read Ethernet PHY address for each port from device tree.

Signed-off-by: Tony Dinh mibodhi@gmail.com

board/Marvell/dreamplug/dreamplug.c | 62 ++++++++++++++++++++++------- 1 file changed, 48 insertions(+), 14 deletions(-)

diff --git a/board/Marvell/dreamplug/dreamplug.c b/board/Marvell/dreamplug/dreamplug.c index e1c64b5224..d5b6b22ddf 100644 --- a/board/Marvell/dreamplug/dreamplug.c +++ b/board/Marvell/dreamplug/dreamplug.c @@ -1,5 +1,6 @@ // SPDX-License-Identifier: GPL-2.0+ /*

• • Copyright (C) 2021 Tony Dinh mibodhi@gmail.com
  • (C) Copyright 2011
  • Jason Cooper u-boot@lakedaemon.net

@@ -97,42 +98,75 @@ int board_init(void) return 0; }

+static int fdt_get_phy_addr(const char *path) +{

• const void *fdt = gd->fdt_blob;
• const u32 *reg;
• const u32 *val;
• int node, phandle, addr;
• /* Find the node by its full path */
• node = fdt_path_offset(fdt, path);
• if (node >= 0) {

• /* Look up phy-handle */
  

• val = fdt_getprop(fdt, node, "phy-handle", NULL);
  

• if (val) {
  

• 	phandle = fdt32_to_cpu(*val);
  

• 	if (!phandle)
  

• 		return -1;
  

• 	/* Follow it to its node */
  

• 	node = fdt_node_offset_by_phandle(fdt, phandle);
  

• 	if (node) {
  

• 		/* Look up reg */
  

• 		reg = fdt_getprop(fdt, node, "reg", NULL);
  

• 		if (reg) {
  

• 			addr = fdt32_to_cpu(*reg);
  

• 			return addr;
  

• 		}
  

• 	}
  

• }
  

• }
• return -1;

+}

You've added this exact some function now for the 3rd time IIRC. Could please please consolidate this function into one of the fdt / dt common functions instead? Perhaps there is already something similar for reading PHY addresses?

Please do this in a follow-up patch, after I've pulled this one.

Other that this:

Reviewed-by: Stefan Roese sr@denx.de

Thanks, Stefan

• #ifdef CONFIG_RESET_PHY_R

-void mv_phy_88e1116_init(char *name) +void mv_phy_88e1116_init(const char *name, const char *path) { u16 reg;

• u16 devadr;

• int phyaddr;

  if (miiphy_set_current_dev(name)) return;

• /* command to read PHY dev address */
• if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {

• printf("Err..%s could not read PHY dev address\n",
  

• 	__func__);
  

• phyaddr = fdt_get_phy_addr(path);
• if (phyaddr < 0) return;

• }

  /*

  • Enable RGMII delay on Tx and Rx for CPU port
  • Ref: sec 4.7.2 of chip datasheet

  */

• miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);

• miiphy_read(name, devadr, MV88E1116_MAC_CTRL2_REG, &reg);

• miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
• miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL2_REG, &reg); reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);

• miiphy_write(name, devadr, MV88E1116_MAC_CTRL2_REG, reg);
• miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);

• miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL2_REG, reg);

• miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);

  /* reset the phy */

• miiphy_reset(name, devadr);

• miiphy_reset(name, phyaddr);

  printf("88E1116 Initialized on %s\n", name); }

  void reset_phy(void) {

• char *eth0_name = "ethernet-controller@72000";

• char *eth0_path = "/ocp@f1000000/ethernet-controller@72000/ethernet0-port@0";

• char *eth1_name = "ethernet-controller@76000";

• char *eth1_path = "/ocp@f1000000/ethernet-controller@72000/ethernet1-port@0";

• /* configure and initialize both PHY's */

• mv_phy_88e1116_init("egiga0");
• mv_phy_88e1116_init("egiga1");

• mv_phy_88e1116_init(eth0_name, eth0_path);
• mv_phy_88e1116_init(eth1_name, eth1_path); } #endif /* CONFIG_RESET_PHY_R */

Viele Grüße, Stefan