This patch extends SiFive FU540 board support to setup ethaddr env variable based on board serialnum read from OTP.
Signed-off-by: Anup Patel anup.patel@wdc.com --- board/sifive/fu540/fu540.c | 122 +++++++++++++++++++++++++++++++++ configs/sifive_fu540_defconfig | 1 + 2 files changed, 123 insertions(+)
diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c index 5adc4a3d4a..11daf1a75a 100644 --- a/board/sifive/fu540/fu540.c +++ b/board/sifive/fu540/fu540.c @@ -8,6 +8,128 @@
#include <common.h> #include <dm.h> +#include <linux/delay.h> +#include <linux/io.h> + +#ifdef CONFIG_MISC_INIT_R + +#define FU540_OTP_BASE_ADDR 0x10070000 + +struct fu540_otp_regs { + u32 pa; /* Address input */ + u32 paio; /* Program address input */ + u32 pas; /* Program redundancy cell selection input */ + u32 pce; /* OTP Macro enable input */ + u32 pclk; /* Clock input */ + u32 pdin; /* Write data input */ + u32 pdout; /* Read data output */ + u32 pdstb; /* Deep standby mode enable input (active low) */ + u32 pprog; /* Program mode enable input */ + u32 ptc; /* Test column enable input */ + u32 ptm; /* Test mode enable input */ + u32 ptm_rep;/* Repair function test mode enable input */ + u32 ptr; /* Test row enable input */ + u32 ptrim; /* Repair function enable input */ + u32 pwe; /* Write enable input (defines program cycle) */ +} __packed; + +#define BYTES_PER_FUSE 4 +#define NUM_FUSES 0x1000 + +static int fu540_otp_read(int offset, void *buf, int size) +{ + struct fu540_otp_regs *regs = (void __iomem *)FU540_OTP_BASE_ADDR; + unsigned int i; + int fuseidx = offset / BYTES_PER_FUSE; + int fusecount = size / BYTES_PER_FUSE; + u32 fusebuf[fusecount]; + + /* check bounds */ + if (offset < 0 || size < 0) + return -EINVAL; + if (fuseidx >= NUM_FUSES) + return -EINVAL; + if ((fuseidx + fusecount) > NUM_FUSES) + return -EINVAL; + + /* init OTP */ + writel(0x01, ®s->pdstb); /* wake up from stand-by */ + writel(0x01, ®s->ptrim); /* enable repair function */ + writel(0x01, ®s->pce); /* enable input */ + + /* read all requested fuses */ + for (i = 0; i < fusecount; i++, fuseidx++) { + writel(fuseidx, ®s->pa); + + /* cycle clock to read */ + writel(0x01, ®s->pclk); + mdelay(1); + writel(0x00, ®s->pclk); + mdelay(1); + + /* read the value */ + fusebuf[i] = readl(®s->pdout); + } + + /* shut down */ + writel(0, ®s->pce); + writel(0, ®s->ptrim); + writel(0, ®s->pdstb); + + /* copy out */ + memcpy(buf, fusebuf, size); + + return 0; +} + +static u32 fu540_read_serialnum(void) +{ + int ret; + u32 serial[2] = {0}; + + for (int i = 0xfe * 4; i > 0; i -= 8) { + ret = fu540_otp_read(i, serial, sizeof(serial)); + if (ret) { + printf("%s: error reading from OTP\n", __func__); + break; + } + if (serial[0] == ~serial[1]) + return serial[0]; + } + + return 0; +} + +static void fu540_setup_macaddr(u32 serialnum) +{ + /* Default MAC address */ + unsigned char mac[6] = { 0x70, 0xb3, 0xd5, 0x92, 0xf0, 0x00 }; + + /* + * We derive our board MAC address by ORing last three bytes + * of board serial number to above default MAC address. + * + * This logic of deriving board MAC address is taken from + * SiFive FSBL and is kept unchanged. + */ + mac[5] |= (serialnum >> 0) & 0xff; + mac[4] |= (serialnum >> 8) & 0xff; + mac[3] |= (serialnum >> 16) & 0xff; + + /* Update environment variable */ + eth_env_set_enetaddr("ethaddr", mac); +} + +int misc_init_r(void) +{ + /* Set ethaddr environment variable if not set */ + if (!env_get("ethaddr")) + fu540_setup_macaddr(fu540_read_serialnum()); + + return 0; +} + +#endif
int board_init(void) { diff --git a/configs/sifive_fu540_defconfig b/configs/sifive_fu540_defconfig index f78412398e..f19203745e 100644 --- a/configs/sifive_fu540_defconfig +++ b/configs/sifive_fu540_defconfig @@ -7,4 +7,5 @@ CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_DISPLAY_CPUINFO=y CONFIG_DISPLAY_BOARDINFO=y +CONFIG_MISC_INIT_R=y CONFIG_OF_PRIOR_STAGE=y