Yes that was it! I had used `log help`, but misunderstood the output. My bad... Below is the debug output I receive, where I don't really get what's happening except for those two lines:
``` uclass_find_device_by_seq() - 1 -1 'usb@47401800' uclass_find_device_by_seq() - not found ```
But I don't really understand what it means. I spent a lot of time reading the available options in menuconfig, and at that point I cannot say what I am doing wrong. Note that I am using the `am335x_evm_defconfig` defconfig, which I changed to get more logging outputs.
Here is the output of `usb start`, let me know if I am missing something obvious from there:
``` => usb start starting USB... Bus usb@47401800: __of_translate_address() OF: ** translation for device usb@47401800 ** __of_translate_address() OF: bus is default (na=1, ns=1) on usb@47400000 __of_translate_address() OF: parent bus is default (na=1, ns=1) on ocp of_translate_one() OF: no ranges, 1:1 translation of_translate_one() OF: with offset: 1195382784 __of_translate_address() OF: parent bus is default (na=1, ns=1) on of_translate_one() OF: no ranges, 1:1 translation of_translate_one() OF: with offset: 1195382784 __of_translate_address() OF: reached root node fdtdec_lookup_phandle() fdtdec_lookup_phandle: phys fdtdec_lookup_phandle() fdtdec_lookup_phandle: ti,ctrl_mod fdtdec_get_addr_size_fixed() fdtdec_get_addr_size_fixed: reg: fdtdec_get_addr_size_fixed() addr=44e10620 fdtdec_get_int() fdtdec_get_int: mentor,multipoint: fdtdec_get_int() 0x1 (1) fdtdec_get_int() fdtdec_get_int: mentor,num-eps: fdtdec_get_int() 0x10 (16) fdtdec_get_int() fdtdec_get_int: mentor,ram-bits: fdtdec_get_int() 0xc (12) fdtdec_get_int() fdtdec_get_int: mentor,power: fdtdec_get_int() 0x1f4 (500) uclass_find_device_by_seq() 0 1 uclass_find_device_by_seq() - 1 -1 'usb@47401800' uclass_find_device_by_seq() - not found clk_set_defaults() clk_set_defaults(usb@47401800) clk_set_default_parents() clk_set_default_parents: could not read assigned-clock-parents for 9df24d30 ofnode_read_prop() ofnode_read_prop: assigned-clock-rates: ofnode_read_prop() <not found> musb_core_init() musb-hdrc: hw_ep 0shared, max 64 musb_core_init() musb-hdrc: hw_ep 1tx, max 512 musb_core_init() musb-hdrc: hw_ep 1rx, max 512 musb_core_init() musb-hdrc: hw_ep 2tx, max 512 musb_core_init() musb-hdrc: hw_ep 2rx, max 512 musb_core_init() musb-hdrc: hw_ep 3tx, max 512 musb_core_init() musb-hdrc: hw_ep 3rx, max 512 musb_core_init() musb-hdrc: hw_ep 4tx, max 512 musb_core_init() musb-hdrc: hw_ep 4rx, max 512 musb_core_init() musb-hdrc: hw_ep 5tx, max 512 musb_core_init() musb-hdrc: hw_ep 5rx, max 512 musb_core_init() musb-hdrc: hw_ep 6tx, max 512 musb_core_init() musb-hdrc: hw_ep 6rx, max 512 musb_core_init() musb-hdrc: hw_ep 7tx, max 512 musb_core_init() musb-hdrc: hw_ep 7rx, max 512 musb_core_init() musb-hdrc: hw_ep 8tx, max 512 musb_core_init() musb-hdrc: hw_ep 8rx, max 512 musb_core_init() musb-hdrc: hw_ep 9tx, max 512 musb_core_init() musb-hdrc: hw_ep 9rx, max 512 musb_core_init() musb-hdrc: hw_ep 10tx, max 256 musb_core_init() musb-hdrc: hw_ep 10rx, max 64 musb_core_init() musb-hdrc: hw_ep 11tx, max 256 musb_core_init() musb-hdrc: hw_ep 11rx, max 64 musb_core_init() musb-hdrc: hw_ep 12tx, max 256 musb_core_init() musb-hdrc: hw_ep 12rx, max 64 musb_core_init() musb-hdrc: hw_ep 13shared, max 4096 musb_core_init() musb-hdrc: hw_ep 14shared, max 1024 musb_core_init() musb-hdrc: hw_ep 15shared, max 1024 musb_start() <== devctl 80 musb_stop() HDRC disabled Port not available. usb_init() scan end ```
Best,
On Sun, Mar 7, 2021 at 3:04 AM Sean Anderson seanga2@gmail.com wrote:
On 3/6/21 8:38 PM, Jonas Vautherin wrote:
Thanks a lot Sean!
I tried to enable logging by using the following CONFIG_:
CONFIG_LOG=y CONFIG_SPL_LOG=y CONFIG_TPL_LOG=y CONFIG_LOG_MAX_LEVEL=5You need to increase this. Log levels are only compiled-in if they are less than the max log level.
CONFIG_SPL_LOG_MAX_LEVEL=3 CONFIG_TPL_LOG_MAX_LEVEL=3 CONFIG_LOG_DEFAULT_LEVEL=7 CONFIG_LOG_CONSOLE=y CONFIG_SPL_LOG_CONSOLE=y CONFIG_TPL_LOG_CONSOLE=y
CONFIG_CMD_LOG=y
And I got the "log" function indeed. But it did not have the effect Iwas hoping for:
=> log level set 7Use the help function ;)
The correct syntax is "log level 7"
If you use a newer U-Boot (newer than 2021.01) then the output will be more verbose. E.g.
=> log level EMERG ALERT CRIT ERR WARNING NOTICE INFO (default) DEBUG
--Sean
=> log level Default log level: 0 => usb start starting USB... Bus usb@47401800: Port not available.
First, I don't get why it says "Default log level: 0" after I set it (towhatever number, apparently). And second, it does not seem to bring me more output about the usb issue :-/.
Am I missing something?
Best, Jonas
On Sat, Mar 6, 2021 at 3:20 AM Sean Anderson <seanga2@gmail.com <mailto:
seanga2@gmail.com>> wrote:
On 3/5/21 7:10 PM, Jonas Vautherin wrote: > Hello! > > I am learning about Fastboot, and I would like to run it fromu-boot and
> detect it from my host computer (I have the tools on my host,that's
> working with other devices). > > I am using a pocketbeagle and I built an image using Yocto. I canget into
> the u-boot prompt at boot time, and I get the following output: > > ``` > Rebooting... reboot: Restarting system > > U-Boot SPL 2020.07 (Jul 06 2020 - 19:22:53 +0000) > Trying to boot from MMC1 > > > U-Boot 2020.07 (Jul 06 2020 - 19:22:53 +0000) > > CPU : AM335X-GP rev 2.1 > Model: TI AM335x PocketBeagle > DRAM: 512 MiB > WDT: Started with servicing (60s timeout) > NAND: 0 MiB > MMC: OMAP SD/MMC: 0 > Loading Environment from FAT... *** Warning - bad CRC, usingdefault
> environment > > <ethaddr> not set. Validating first E-fuse MAC > Net: No ethernet found. > Hit any key to stop autoboot: 2 > ``` > > If I hit a key here, I get the u-boot prompt (`=>`) where I find > "fastboot". The thing is that none of the fastboot commands I runhave any
> output: This is normal. There will be output only when you issue commands. > > * fastboot usb 0 > * fastboot usb > * fastboot udp > > Now, fastboot udp is not enabled in my defconfig, but the udpgadget
> support is, and the usb fastboot gadget is enabled, too. From myhost, I
> just don't see anything in the `dmesg` output. > > Here are a few questions: > > * Does fastboot usb go over ethernet? If yes, I guess that the"Net: No
> ethernet found." message is an issue that I need to fix such thata new usb
> network interface is created by my host, but from my tests withthis
> proprietary device I own, it does not seem to be enumerated as anetwork
> interface. Only udp goes over ethernet (though I suppose you could use a usb-ethernet gadget/dongle). > * In readthedocs [1], it mentions that "TheCONFIG_USB_GADGET_VENDOR_NUM
> must be one of the numbers supported by the fastboot client." Inmy setup,
> it is set to 0x0451, and I did not find what is supposed to besupported in
> fastboot.cpp [2]. So from the host, I also tried `fastboot -i0x0451
> devices`. Is that an issue? The fastboot client detects devices with two bulk endpoints and the correct interface (see match_fastboot and filter_usb_device).Generally,
you will only have to specify the vid/pid/serial if you have multiple devices plugged in at once. > * I thought that maybe I should start USB, because the output of`usb tree`
> says "USB is stopped. Please issue 'usb start' first.". Butrunning `usb
> start` errors with "Bus usb@47401800: Port not available.". Isthat related
> to fastboot at all, i.e. should I be concerned about that? Andhow can I
> debug it? That's probably why your fastboot isn't working :) You can try debugging it by enabling debug messages. If you wantless than
a firehose, you can try setting the default log level to info, andthen
setting it to debug before running usb start. See [1] for details. [1] https://u-boot.readthedocs.io/en/latest/develop/logging.html --Sean > Thanks in advance for the help! > Jonas > > [1]:https://u-boot.readthedocs.io/en/latest/android/fastboot.html
> [2]: >https://android.googlesource.com/platform/system/core/+/master/fastboot/fast...
>