From: Robert Beckett bob.beckett@collabora.com
Remove old (pre-DM) i2c setup code. Enable DM i2c. Convert common code to use DM rtc. Convert common code to read VPD from eeprom partition. Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only: Correct RTC compatible in device tree. Enable MXC DM i2c driver. Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc. Make GPIO banks available during preloc, since initialisation is done in board_early_init_f(). Add gpio_request() calls to satisfy the DM_GPIO compatibility API. Remove unused power configuration.
Signed-off-by: Robert Beckett bob.beckett@collabora.com Signed-off-by: Ian Ray ian.ray@ge.com --- Note: this is a squash of a few commits due to dropping of i2c compat api --- arch/arm/dts/imx53-ppd-uboot.dtsi | 20 +++++++ arch/arm/dts/imx53-ppd.dts | 2 +- board/ge/bx50v3/Kconfig | 2 - board/ge/bx50v3/bx50v3.c | 114 ++++++++------------------------------ board/ge/common/Kconfig | 14 ----- board/ge/common/ge_common.c | 17 ++---- board/ge/common/vpd_reader.c | 37 ++++++++----- board/ge/mx53ppd/Kconfig | 2 - board/ge/mx53ppd/mx53ppd.c | 35 +----------- board/ge/mx53ppd/mx53ppd_video.c | 1 + configs/ge_bx50v3_defconfig | 15 ++++- configs/mx53ppd_defconfig | 12 +++- include/configs/ge_bx50v3.h | 27 --------- include/configs/mx53ppd.h | 35 ------------ 14 files changed, 97 insertions(+), 236 deletions(-) delete mode 100644 board/ge/common/Kconfig
diff --git a/arch/arm/dts/imx53-ppd-uboot.dtsi b/arch/arm/dts/imx53-ppd-uboot.dtsi index 99d409d..8e45ee7 100644 --- a/arch/arm/dts/imx53-ppd-uboot.dtsi +++ b/arch/arm/dts/imx53-ppd-uboot.dtsi @@ -26,3 +26,23 @@ }; }; }; + +&gpio1 { + u-boot,dm-pre-reloc; +}; + +&gpio2 { + u-boot,dm-pre-reloc; +}; + +&gpio3 { + u-boot,dm-pre-reloc; +}; + +&gpio4 { + u-boot,dm-pre-reloc; +}; + +&gpio5 { + u-boot,dm-pre-reloc; +}; diff --git a/arch/arm/dts/imx53-ppd.dts b/arch/arm/dts/imx53-ppd.dts index 016a859..a627847 100644 --- a/arch/arm/dts/imx53-ppd.dts +++ b/arch/arm/dts/imx53-ppd.dts @@ -489,7 +489,7 @@ reg = <1>;
rtc@30 { - compatible = "sii,s35390a"; + compatible = "sii,s35392a-rtc"; reg = <0x30>; };
diff --git a/board/ge/bx50v3/Kconfig b/board/ge/bx50v3/Kconfig index 0593856..993b055 100644 --- a/board/ge/bx50v3/Kconfig +++ b/board/ge/bx50v3/Kconfig @@ -15,6 +15,4 @@ config SYS_SOC config SYS_CONFIG_NAME default "ge_bx50v3"
-source "board/ge/common/Kconfig" - endif diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c index 89607cf..4a75c7b 100644 --- a/board/ge/bx50v3/bx50v3.c +++ b/board/ge/bx50v3/bx50v3.c @@ -14,7 +14,6 @@ #include <linux/errno.h> #include <linux/libfdt.h> #include <asm/gpio.h> -#include <asm/mach-imx/mxc_i2c.h> #include <asm/mach-imx/iomux-v3.h> #include <asm/mach-imx/boot_mode.h> #include <asm/mach-imx/video.h> @@ -27,7 +26,8 @@ #include <asm/arch/crm_regs.h> #include <asm/io.h> #include <asm/arch/sys_proto.h> -#include <i2c.h> +#include <power/regulator.h> +#include <power/da9063_pmic.h> #include <input.h> #include <pwm.h> #include <version.h> @@ -85,45 +85,6 @@ static iomux_v3_cfg_t const uart4_pads[] = { MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), };
-static struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD, - .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD, - .gp = IMX_GPIO_NR(5, 27) - }, - .sda = { - .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD, - .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD, - .gp = IMX_GPIO_NR(5, 26) - } -}; - -static struct i2c_pads_info i2c_pad_info2 = { - .scl = { - .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD, - .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD, - .gp = IMX_GPIO_NR(4, 12) - }, - .sda = { - .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD, - .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD, - .gp = IMX_GPIO_NR(4, 13) - } -}; - -static struct i2c_pads_info i2c_pad_info3 = { - .scl = { - .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD, - .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD, - .gp = IMX_GPIO_NR(1, 3) - }, - .sda = { - .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD, - .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD, - .gp = IMX_GPIO_NR(1, 6) - } -}; - static void setup_iomux_uart(void) { imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads)); @@ -491,10 +452,6 @@ static void set_confidx(const struct vpd_cache* vpd)
int board_init(void) { - setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); - setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); - if (!read_vpd(&vpd, vpd_callback)) { int ret, rescan;
@@ -541,53 +498,26 @@ static const struct boot_mode board_boot_modes[] = {
void pmic_init(void) { -#define I2C_PMIC 0x2 -#define DA9063_I2C_ADDR 0x58 -#define DA9063_REG_BCORE2_CFG 0x9D -#define DA9063_REG_BCORE1_CFG 0x9E -#define DA9063_REG_BPRO_CFG 0x9F -#define DA9063_REG_BIO_CFG 0xA0 -#define DA9063_REG_BMEM_CFG 0xA1 -#define DA9063_REG_BPERI_CFG 0xA2 -#define DA9063_BUCK_MODE_MASK 0xC0 -#define DA9063_BUCK_MODE_MANUAL 0x00 -#define DA9063_BUCK_MODE_SLEEP 0x40 -#define DA9063_BUCK_MODE_SYNC 0x80 -#define DA9063_BUCK_MODE_AUTO 0xC0 - - uchar val; - - i2c_set_bus_num(I2C_PMIC); - - i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1); - val &= ~DA9063_BUCK_MODE_MASK; - val |= DA9063_BUCK_MODE_SYNC; - i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1); - - i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1); - val &= ~DA9063_BUCK_MODE_MASK; - val |= DA9063_BUCK_MODE_SYNC; - i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1); - - i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1); - val &= ~DA9063_BUCK_MODE_MASK; - val |= DA9063_BUCK_MODE_SYNC; - i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1); - - i2c_read(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1); - val &= ~DA9063_BUCK_MODE_MASK; - val |= DA9063_BUCK_MODE_SYNC; - i2c_write(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1); - - i2c_read(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1); - val &= ~DA9063_BUCK_MODE_MASK; - val |= DA9063_BUCK_MODE_SYNC; - i2c_write(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1); - - i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1); - val &= ~DA9063_BUCK_MODE_MASK; - val |= DA9063_BUCK_MODE_SYNC; - i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1); + struct udevice *reg; + int ret, i; + static const char * const bucks[] = { + "bcore1", + "bcore2", + "bpro", + "bmem", + "bio", + "bperi", + }; + + for (i = 0; i < ARRAY_SIZE(bucks); i++) { + ret = regulator_get_by_devname(bucks[i], ®); + if (reg < 0) { + printf("%s(): Unable to get regulator %s: %d\n", + __func__, bucks[i], ret); + continue; + } + regulator_set_mode(reg, DA9063_BUCKMODE_SYNC); + } }
int board_late_init(void) diff --git a/board/ge/common/Kconfig b/board/ge/common/Kconfig deleted file mode 100644 index 637b264..0000000 --- a/board/ge/common/Kconfig +++ /dev/null @@ -1,14 +0,0 @@ -config SYS_VPD_EEPROM_I2C_ADDR - hex "I2C address of the EEPROM device used for VPD" - help - VPD = Vital Product Data - -config SYS_VPD_EEPROM_I2C_BUS - int "I2C bus of the EEPROM device used for VPD." - -config SYS_VPD_EEPROM_SIZE - int "Size in bytes of the EEPROM device used for VPD" - -config SYS_VPD_EEPROM_I2C_ADDR_LEN - int "Number of bytes to use for VPD EEPROM address" - default 1 diff --git a/board/ge/common/ge_common.c b/board/ge/common/ge_common.c index d7e21de..48c3778 100644 --- a/board/ge/common/ge_common.c +++ b/board/ge/common/ge_common.c @@ -5,27 +5,24 @@
#include <common.h> #include <env.h> -#include <i2c.h> +#include <dm/uclass.h> #include <rtc.h>
void check_time(void) { + struct udevice *dev; int ret, i; struct rtc_time tm; u8 retry = 3;
- unsigned int current_i2c_bus = i2c_get_bus_num(); - - ret = i2c_set_bus_num(CONFIG_SYS_RTC_BUS_NUM); - if (ret < 0) { + ret = uclass_get_device(UCLASS_RTC, 0, &dev); + if (ret) { env_set("rtc_status", "FAIL"); return; }
- rtc_init(); - for (i = 0; i < retry; i++) { - ret = rtc_get(&tm); + ret = dm_rtc_get(dev, &tm); if (!ret || ret == -EINVAL) break; } @@ -40,7 +37,7 @@ void check_time(void) tm.tm_year = 2036;
for (i = 0; i < retry; i++) { - ret = rtc_set(&tm); + ret = dm_rtc_set(dev, &tm); if (!ret) break; } @@ -55,7 +52,5 @@ void check_time(void) env_set("rtc_status", "2038"); else env_set("rtc_status", "OK"); - - i2c_set_bus_num(current_i2c_bus); }
diff --git a/board/ge/common/vpd_reader.c b/board/ge/common/vpd_reader.c index 12410d9..4df411c 100644 --- a/board/ge/common/vpd_reader.c +++ b/board/ge/common/vpd_reader.c @@ -8,6 +8,9 @@ #include <i2c.h> #include <linux/bch.h> #include <stdlib.h> +#include <dm/uclass.h> +#include <i2c_eeprom.h> +#include <hexdump.h>
/* BCH configuration */
@@ -200,28 +203,34 @@ int read_vpd(struct vpd_cache *cache, int (*process_block)(struct vpd_cache *, u8 id, u8 version, u8 type, size_t size, u8 const *data)) { - static const size_t size = CONFIG_SYS_VPD_EEPROM_SIZE; - - int res; + struct udevice *dev; + int ret; u8 *data; - unsigned int current_i2c_bus = i2c_get_bus_num(); + int size; + + ret = uclass_get_device_by_name(UCLASS_I2C_EEPROM, "vpd", &dev); + if (ret) + return ret;
- res = i2c_set_bus_num(CONFIG_SYS_VPD_EEPROM_I2C_BUS); - if (res < 0) - return res; + size = i2c_eeprom_size(dev); + if (size < 0) { + printf("Unable to get size of eeprom: %d\n", ret); + return ret; + }
data = malloc(size); if (!data) return -ENOMEM;
- res = i2c_read(CONFIG_SYS_VPD_EEPROM_I2C_ADDR, 0, - CONFIG_SYS_VPD_EEPROM_I2C_ADDR_LEN, - data, size); - if (res == 0) - res = vpd_reader(size, data, cache, process_block); + ret = i2c_eeprom_read(dev, 0, data, size); + if (ret) { + free(data); + return ret; + } + + ret = vpd_reader(size, data, cache, process_block);
free(data);
- i2c_set_bus_num(current_i2c_bus); - return res; + return ret; } diff --git a/board/ge/mx53ppd/Kconfig b/board/ge/mx53ppd/Kconfig index bebb2fa..6dc3818 100644 --- a/board/ge/mx53ppd/Kconfig +++ b/board/ge/mx53ppd/Kconfig @@ -13,6 +13,4 @@ config SYS_SOC config SYS_CONFIG_NAME default "mx53ppd"
-source "board/ge/common/Kconfig" - endif diff --git a/board/ge/mx53ppd/mx53ppd.c b/board/ge/mx53ppd/mx53ppd.c index 105edd2..ea3f217 100644 --- a/board/ge/mx53ppd/mx53ppd.c +++ b/board/ge/mx53ppd/mx53ppd.c @@ -125,34 +125,6 @@ static void setup_iomux_fec(void) imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); }
-#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \ - PAD_CTL_PUS_100K_UP | PAD_CTL_ODE) - -static void setup_iomux_i2c(void) -{ - static const iomux_v3_cfg_t i2c1_pads[] = { - NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL), - }; - - imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads)); -} - -#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL) - -static struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode = MX53_PAD_EIM_D21__I2C1_SCL | I2C_PAD, - .gpio_mode = MX53_PAD_EIM_D28__GPIO3_28 | I2C_PAD, - .gp = IMX_GPIO_NR(3, 28) - }, - .sda = { - .i2c_mode = MX53_PAD_EIM_D28__I2C1_SDA | I2C_PAD, - .gpio_mode = MX53_PAD_EIM_D21__GPIO3_21 | I2C_PAD, - .gp = IMX_GPIO_NR(3, 21) - } -}; - static int clock_1GHz(void) { int ret; @@ -182,8 +154,10 @@ void ppd_gpio_init(void) int i;
imx_iomux_v3_setup_multiple_pads(ppd_pads, ARRAY_SIZE(ppd_pads)); - for (i = 0; i < ARRAY_SIZE(ppd_gpios); ++i) + for (i = 0; i < ARRAY_SIZE(ppd_gpios); ++i) { + gpio_request(ppd_gpios[i].gpio, "request"); gpio_direction_output(ppd_gpios[i].gpio, ppd_gpios[i].value); + } }
int board_early_init_f(void) @@ -256,9 +230,6 @@ int board_init(void) gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
mxc_set_sata_internal_clock(); - setup_iomux_i2c(); - - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
return 0; } diff --git a/board/ge/mx53ppd/mx53ppd_video.c b/board/ge/mx53ppd/mx53ppd_video.c index 394dcd6..9dd9f0c 100644 --- a/board/ge/mx53ppd/mx53ppd_video.c +++ b/board/ge/mx53ppd/mx53ppd_video.c @@ -104,6 +104,7 @@ static void lcd_enable(void) pwm_config(1, 5000000, 5000000);
/* Backlight Power */ + gpio_request(BACKLIGHT_ENABLE, "BACKLIGHT_ENABLE"); gpio_direction_output(BACKLIGHT_ENABLE, 1);
pwm_enable(1); diff --git a/configs/ge_bx50v3_defconfig b/configs/ge_bx50v3_defconfig index 37bcf06..384327e 100644 --- a/configs/ge_bx50v3_defconfig +++ b/configs/ge_bx50v3_defconfig @@ -2,9 +2,6 @@ CONFIG_ARM=y CONFIG_ARCH_MX6=y CONFIG_SYS_TEXT_BASE=0x17800000 CONFIG_SYS_MALLOC_F_LEN=0x4000 -CONFIG_SYS_VPD_EEPROM_I2C_ADDR=0x50 -CONFIG_SYS_VPD_EEPROM_I2C_BUS=4 -CONFIG_SYS_VPD_EEPROM_SIZE=1024 CONFIG_TARGET_GE_BX50V3=y CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_SECT_SIZE=0x10000 @@ -51,6 +48,12 @@ CONFIG_BOOTCOUNT_EXT=y CONFIG_BOOTCOUNT_BOOTLIMIT=10 CONFIG_SYS_BOOTCOUNT_EXT_DEVPART="1:5" CONFIG_DM_MMC=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MXC=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_FSL_USDHC=y CONFIG_MTD=y @@ -71,6 +74,12 @@ CONFIG_DM_PCI=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_PWM_IMX=y +CONFIG_DM_PMIC=y +CONFIG_DM_PMIC_DA9063=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_DA9063=y +CONFIG_DM_RTC=y +CONFIG_RTC_RX8010SJ=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_MXC_SPI=y diff --git a/configs/mx53ppd_defconfig b/configs/mx53ppd_defconfig index 6cfb526..4b479ae 100644 --- a/configs/mx53ppd_defconfig +++ b/configs/mx53ppd_defconfig @@ -2,9 +2,6 @@ CONFIG_ARM=y CONFIG_ARCH_MX5=y CONFIG_SYS_TEXT_BASE=0x77800000 CONFIG_TARGET_MX53PPD=y -CONFIG_SYS_VPD_EEPROM_I2C_ADDR=0x50 -CONFIG_SYS_VPD_EEPROM_I2C_BUS=2 -CONFIG_SYS_VPD_EEPROM_SIZE=1024 CONFIG_ENV_SIZE=0x2800 CONFIG_ENV_OFFSET=0xC0000 CONFIG_NR_DRAM_BANKS=2 @@ -41,6 +38,13 @@ CONFIG_BOOTCOUNT_LIMIT=y CONFIG_BOOTCOUNT_EXT=y CONFIG_BOOTCOUNT_BOOTLIMIT=10 CONFIG_SYS_BOOTCOUNT_EXT_DEVPART="0:5" +CONFIG_DM_GPIO=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MXC=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y CONFIG_DM_MMC=y CONFIG_FSL_ESDHC_IMX=y CONFIG_MTD=y @@ -49,6 +53,7 @@ CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX5=y CONFIG_DM_REGULATOR=y CONFIG_PWM_IMX=y +CONFIG_DM_RTC=y CONFIG_RTC_S35392A=y CONFIG_SYSRESET=y CONFIG_SYSRESET_WATCHDOG=y @@ -60,3 +65,4 @@ CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set CONFIG_WATCHDOG_TIMEOUT_MSECS=8000 CONFIG_IMX_WATCHDOG=y +CONFIG_SYS_MALLOC_F_LEN=0x4000 diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h index dad906d..b8b1ec7 100644 --- a/include/configs/ge_bx50v3.h +++ b/include/configs/ge_bx50v3.h @@ -189,33 +189,6 @@ #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) #define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
-#define CONFIG_RTC_RX8010SJ -#define CONFIG_SYS_RTC_BUS_NUM 2 -#define CONFIG_SYS_I2C_RTC_ADDR 0x32 - -/* I2C Configs */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_MXC_I2C1 -#define CONFIG_SYS_I2C_MXC_I2C2 -#define CONFIG_SYS_I2C_MXC_I2C3 - -#define CONFIG_SYS_NUM_I2C_BUSES 11 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ - {1, {I2C_NULL_HOP} }, \ - {2, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \ - } - #define CONFIG_BCH
#endif /* __GE_BX50V3_CONFIG_H */ diff --git a/include/configs/mx53ppd.h b/include/configs/mx53ppd.h index 9361507..a11b085 100644 --- a/include/configs/mx53ppd.h +++ b/include/configs/mx53ppd.h @@ -43,25 +43,6 @@ #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0
-#define CONFIG_SYS_RTC_BUS_NUM 2 -#define CONFIG_SYS_I2C_RTC_ADDR 0x30 - -/* I2C Configs */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ -#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ -#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ - -/* PMIC Controller */ -#define CONFIG_POWER -#define CONFIG_POWER_I2C -#define CONFIG_DIALOG_POWER -#define CONFIG_POWER_FSL -#define CONFIG_POWER_FSL_MC13892 -#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48 -#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8 - /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_BAUDRATE 115200 @@ -188,22 +169,6 @@ #define CONFIG_CMD_FUSE #define CONFIG_FSL_IIM
-#define CONFIG_SYS_I2C_SPEED 100000 - -/* I2C1 */ -#define CONFIG_SYS_NUM_I2C_BUSES 9 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \ - } - #define CONFIG_BCH
/* Backlight Control */