The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator.
Signed-off-by: Rai Harninder harninder.rai@nxp.com --- .../include/asm/arch-fsl-layerscape/immap_lsch3.h | 4 ++++ board/freescale/common/vid.c | 15 ++++++++++++++- board/freescale/ls2080ardb/ls2080ardb.c | 5 +++++ include/configs/ls2080ardb.h | 16 ++++++++++++++++ 4 files changed, 39 insertions(+), 1 deletions(-)
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h index 91f3ce8..4fd58ee 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h @@ -146,6 +146,10 @@ struct ccsr_gur { u8 res_008[0x20-0x8]; u32 gpporcr1; /* General-purpose POR configuration */ u32 gpporcr2; /* General-purpose POR configuration 2 */ +#define FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT 25 +#define FSL_CHASSIS3_DCFG_FUSESR_VID_MASK 0x1F +#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT 20 +#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK 0x1F u32 dcfg_fusesr; /* Fuse status register */ u32 gpporcr3; u32 gpporcr4; diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c index 1bd65a8..16ae177 100644 --- a/board/freescale/common/vid.c +++ b/board/freescale/common/vid.c @@ -10,6 +10,8 @@ #include <asm/io.h> #ifdef CONFIG_LS1043A #include <asm/arch/immap_lsch2.h> +#elif defined(CONFIG_FSL_LAYERSCAPE) +#include <asm/arch/immap_lsch3.h> #else #include <asm/immap_85xx.h> #endif @@ -285,7 +287,7 @@ static int set_voltage(int i2caddress, int vdd) int adjust_vdd(ulong vdd_override) { int re_enable = disable_interrupts(); -#ifdef CONFIG_LS1043A +#if defined(CONFIG_LS1043A) || defined(CONFIG_FSL_LAYERSCAPE) struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); #else ccsr_gur_t __iomem *gur = @@ -362,7 +364,11 @@ int adjust_vdd(ulong vdd_override) }
/* get the voltage ID from fuse status register */ +#ifdef CONFIG_FSL_LAYERSCAPE + fusesr = in_le32(&gur->dcfg_fusesr); +#else fusesr = in_be32(&gur->dcfg_fusesr); +#endif /* * VID is used according to the table below * --------------------------------------- @@ -387,6 +393,13 @@ int adjust_vdd(ulong vdd_override) vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) & FSL_CHASSIS2_DCFG_FUSESR_VID_MASK; } +#elif defined(CONFIG_FSL_LAYERSCAPE) + vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT) & + FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK; + if ((vid == 0) || (vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK)) { + vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT) & + FSL_CHASSIS3_DCFG_FUSESR_VID_MASK; + } #else vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; diff --git a/board/freescale/ls2080ardb/ls2080ardb.c b/board/freescale/ls2080ardb/ls2080ardb.c index c63b639..9515b25 100644 --- a/board/freescale/ls2080ardb/ls2080ardb.c +++ b/board/freescale/ls2080ardb/ls2080ardb.c @@ -122,6 +122,11 @@ int select_i2c_ch_pca9547(u8 ch) return 0; }
+int i2c_multiplexer_select_vid_channel(u8 channel) +{ + return select_i2c_ch_pca9547(channel); +} + int config_board_mux(int ctrl_type) { u8 reg5; diff --git a/include/configs/ls2080ardb.h b/include/configs/ls2080ardb.h index 116dbcd..9a95f31 100644 --- a/include/configs/ls2080ardb.h +++ b/include/configs/ls2080ardb.h @@ -14,6 +14,22 @@
#define CONFIG_DISPLAY_BOARDINFO
+#define I2C_MUX_CH_VOL_MONITOR 0xa +#define I2C_VOL_MONITOR_ADDR 0x38 +#define CONFIG_VOL_MONITOR_IR36021_READ +#define CONFIG_VOL_MONITOR_IR36021_SET + +#define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" +#ifndef CONFIG_SPL_BUILD +#define CONFIG_VID +#endif +/* step the IR regulator in 5mV increments */ +#define IR_VDD_STEP_DOWN 5 +#define IR_VDD_STEP_UP 5 +/* The lowest and highest voltage allowed for LS2080ARDB */ +#define VDD_MV_MIN 819 +#define VDD_MV_MAX 1212 + #ifndef __ASSEMBLY__ unsigned long get_board_sys_clk(void); #endif