Now that we have a device-tree include file with common MMC/SD IOdelay data for DRA76x SoC, shift the EVM device-tree file to using that. Also fix the name of the IO voltage regulator for mmc1.
Signed-off-by: Jean-Jacques Hiblot jjhiblot@ti.com ---
arch/arm/dts/dra76-evm.dts | 51 ++++++++-------------------------------------- 1 file changed, 8 insertions(+), 43 deletions(-)
diff --git a/arch/arm/dts/dra76-evm.dts b/arch/arm/dts/dra76-evm.dts index b024a65..a1f289f 100644 --- a/arch/arm/dts/dra76-evm.dts +++ b/arch/arm/dts/dra76-evm.dts @@ -9,6 +9,7 @@
#include "dra76x.dtsi" #include "dra7-evm-common.dtsi" +#include "dra76x-mmc-iodelay.dtsi" #include <dt-bindings/net/ti-dp83867.h>
/ { @@ -100,46 +101,6 @@ }; };
-&dra7_pmx_core { - mmc1_pins_default: mmc1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ - DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ - DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ - >; - }; - - mmc1_pins_sdr12: pinmux_mmc1_sdr12_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ - DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ - >; - }; - - mmc2_pins_default: mmc2_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ - DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ - DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ - DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ - DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ - DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ - DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ - DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ - DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ - DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ - >; - }; -}; - &i2c1 { status = "okay"; clock-frequency = <400000>; @@ -345,23 +306,27 @@ &mmc1 { status = "okay"; vmmc-supply = <&vio_3v3_sd>; - vmmc_aux-supply = <&ldo4_reg>; + vqmmc-supply = <&ldo4_reg>; bus-width = <4>; /* * SDCD signal is not being used here - using the fact that GPIO mode * is always hardwired. */ cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_hs>; };
&mmc2 { status = "okay"; vmmc-supply = <&vio_1v8>; bus-width = <8>; - pinctrl-names = "default"; + pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v"; pinctrl-0 = <&mmc2_pins_default>; + pinctrl-1 = <&mmc2_pins_default>; + pinctrl-2 = <&mmc2_pins_default>; + pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_conf>; };
/* No RTC on this device */