The MMC booting wasn't previously fitting into the codespace. This patch enables MMC booting from the baseboard by reducing some DM overhead during SPL.
Signed-off-by: Adam Ford aford173@gmail.com --- V2: Recalculate MMC index so it can boot from either internal SOM or baseboard micro SD socket.
diff --git a/board/logicpd/imx6/imx6logic.c b/board/logicpd/imx6/imx6logic.c index ce1c8a5d6b..89cf53c24d 100644 --- a/board/logicpd/imx6/imx6logic.c +++ b/board/logicpd/imx6/imx6logic.c @@ -60,6 +60,7 @@ static iomux_v3_cfg_t const uart3_pads[] = { MX6_PAD_EIM_EB3__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), };
+#ifndef CONFIG_SPL_BUILD static void fixup_enet_clock(void) { struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; @@ -108,6 +109,7 @@ static void fixup_enet_clock(void) dm_gpio_set_value(&reset, 1); mdelay(50); } +#endif
static void setup_iomux_uart(void) { @@ -158,7 +160,9 @@ int overwrite_console(void)
int board_early_init_f(void) { +#ifndef CONFIG_SPL_BUILD fixup_enet_clock(); +#endif setup_iomux_uart(); setup_nand_pins(); return 0; @@ -200,6 +204,74 @@ int spl_start_uboot(void) } #endif
+/* SD interface */ +#define USDHC_PAD_CTRL \ + (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +static iomux_v3_cfg_t const usdhc1_pads[] = { + MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ +}; + +#ifdef CONFIG_FSL_ESDHC +struct fsl_esdhc_cfg usdhc_cfg[] = { + {USDHC1_BASE_ADDR}, /* SOM */ + {USDHC2_BASE_ADDR} /* Baseboard */ +}; + +int board_mmc_init(bd_t *bis) +{ + struct src *psrc = (struct src *)SRC_BASE_ADDR; + unsigned int reg = readl(&psrc->sbmr1) >> 11; + /* + * Upon reading BOOT_CFG register the following map is done: + * Bit 11 and 12 of BOOT_CFG register can determine the current + * mmc port + * 0x1 SD1-SOM + * 0x2 SD2-Baseboard + */ + + reg &= 0x3; /* Only care about bottom 2 bits */ + + switch (reg) { + case 0: + SETUP_IOMUX_PADS(usdhc1_pads); + usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR; + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; + break; + case 1: + SETUP_IOMUX_PADS(usdhc2_pads); + usdhc_cfg[1].esdhc_base = USDHC2_BASE_ADDR; + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + gd->arch.sdhc_clk = usdhc_cfg[1].sdhc_clk; + break; + } + + return fsl_esdhc_initialize(bis, &usdhc_cfg[reg]); +} + +int board_mmc_getcd(struct mmc *mmc) +{ + return 1; +} +#endif + static void ccgr_init(void) { struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; diff --git a/configs/imx6q_logic_defconfig b/configs/imx6q_logic_defconfig index 036069a437..d0362665bb 100644 --- a/configs/imx6q_logic_defconfig +++ b/configs/imx6q_logic_defconfig @@ -4,25 +4,25 @@ CONFIG_SYS_TEXT_BASE=0x17800000 CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_TARGET_MX6LOGICPD=y +CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 CONFIG_SPL=y +CONFIG_SPL_FAT_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x400 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg" CONFIG_BOOTDELAY=3 # CONFIG_USE_BOOTCOMMAND is not set CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y -# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set CONFIG_SPL_SEPARATE_BSS=y +# CONFIG_TPL_BANNER_PRINT is not set +# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set CONFIG_SPL_DMA_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y -CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_PAYLOAD="u-boot.img" CONFIG_SPL_USB_HOST_SUPPORT=y CONFIG_SPL_USB_GADGET_SUPPORT=y CONFIG_SPL_USB_SDP_SUPPORT=y @@ -47,11 +47,9 @@ CONFIG_CMD_MTDPARTS=y CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand" CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:2m(spl),2m(uboot),1m(env),16m(kernel),1m(dtb),-(fs)" CONFIG_CMD_UBI=y -CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="imx6q-logicpd" CONFIG_ENV_IS_IN_NAND=y CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y -CONFIG_SPL_DM=y CONFIG_PCF8575_GPIO=y CONFIG_SYS_I2C_MXC=y CONFIG_LED=y @@ -64,7 +62,6 @@ CONFIG_PHY_ATHEROS=y CONFIG_FEC_MXC=y CONFIG_MII=y CONFIG_PINCTRL=y -CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_PMIC_PFUZE100=y CONFIG_MXC_UART=y