This patch removes hardcoded gpio settings as they have been replaced by pinctrl in dts, and also replaces regmap-based phy reset with a more generic reset controller.
Reviewed-by: Stefan Roese sr@denx.de Signed-off-by: Weijie Gao weijie.gao@mediatek.com --- drivers/net/mt7628-eth.c | 45 +++++++--------------------------------- 1 file changed, 8 insertions(+), 37 deletions(-)
diff --git a/drivers/net/mt7628-eth.c b/drivers/net/mt7628-eth.c index 7833b2f47a..4675b0f003 100644 --- a/drivers/net/mt7628-eth.c +++ b/drivers/net/mt7628-eth.c @@ -18,23 +18,12 @@ #include <malloc.h> #include <miiphy.h> #include <net.h> -#include <regmap.h> -#include <syscon.h> +#include <reset.h> #include <wait_bit.h> #include <asm/io.h> #include <linux/bitfield.h> #include <linux/err.h>
-/* System controller register */ -#define MT7628_RSTCTRL_REG 0x34 -#define RSTCTRL_EPHY_RST BIT(24) - -#define MT7628_AGPIO_CFG_REG 0x3c -#define MT7628_EPHY_GPIO_AIO_EN GENMASK(20, 17) -#define MT7628_EPHY_P0_DIS BIT(16) - -#define MT7628_GPIO2_MODE_REG 0x64 - /* Ethernet frame engine register */ #define PDMA_RELATED 0x0800
@@ -137,7 +126,6 @@ struct fe_tx_dma { struct mt7628_eth_dev { void __iomem *base; /* frame engine base address */ void __iomem *eth_sw_base; /* switch base address */ - struct regmap *sysctrl_regmap; /* system-controller reg-map */
struct mii_dev *bus;
@@ -150,6 +138,8 @@ struct mt7628_eth_dev { int rx_dma_idx; /* Point to the next TXD in TXD Ring0 CPU wants to use */ int tx_dma_idx; + + struct reset_ctl rst_ephy; };
static int mdio_wait_read(struct mt7628_eth_dev *priv, u32 mask, bool mask_set) @@ -301,20 +291,9 @@ static void rt305x_esw_init(struct mt7628_eth_dev *priv) /* 1us cycle number=125 (FE's clock=125Mhz) */ writel(0x7d000000, base + MT7628_SWITCH_BMU_CTRL);
- /* Configure analog GPIO setup */ - regmap_update_bits(priv->sysctrl_regmap, MT7628_AGPIO_CFG_REG, - MT7628_EPHY_P0_DIS, MT7628_EPHY_GPIO_AIO_EN); - /* Reset PHY */ - regmap_update_bits(priv->sysctrl_regmap, MT7628_RSTCTRL_REG, - 0, RSTCTRL_EPHY_RST); - regmap_update_bits(priv->sysctrl_regmap, MT7628_RSTCTRL_REG, - RSTCTRL_EPHY_RST, 0); - mdelay(10); - - /* Set P0 EPHY LED mode */ - regmap_update_bits(priv->sysctrl_regmap, MT7628_GPIO2_MODE_REG, - 0x0ffc0ffc, 0x05540554); + reset_assert(&priv->rst_ephy); + reset_deassert(&priv->rst_ephy); mdelay(10);
mt7628_ephy_init(priv); @@ -558,7 +537,6 @@ static void mt7628_eth_stop(struct udevice *dev) static int mt7628_eth_probe(struct udevice *dev) { struct mt7628_eth_dev *priv = dev_get_priv(dev); - struct udevice *syscon; struct mii_dev *bus; int ret; int i; @@ -573,20 +551,13 @@ static int mt7628_eth_probe(struct udevice *dev) if (IS_ERR(priv->eth_sw_base)) return PTR_ERR(priv->eth_sw_base);
- /* Get system controller regmap */ - ret = uclass_get_device_by_phandle(UCLASS_SYSCON, dev, - "syscon", &syscon); + /* Reset controller */ + ret = reset_get_by_name(dev, "ephy", &priv->rst_ephy); if (ret) { - pr_err("unable to find syscon device\n"); + pr_err("unable to find reset controller for ethernet PHYs\n"); return ret; }
- priv->sysctrl_regmap = syscon_get_regmap(syscon); - if (!priv->sysctrl_regmap) { - pr_err("unable to find regmap\n"); - return -ENODEV; - } - /* Put rx and tx rings into KSEG1 area (uncached) */ priv->tx_ring = (struct fe_tx_dma *) KSEG1ADDR(memalign(ARCH_DMA_MINALIGN,