Signed-off-by: Jon Loeliger jdl@freescale.com --- README | 179 +++++++++++++++++++++++++++++++--------------------------------- 1 files changed, 86 insertions(+), 93 deletions(-)
diff --git a/README b/README index bb5b46e..a451819 100644 --- a/README +++ b/README @@ -541,7 +541,7 @@ The following options need to be configured: CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c) CONFIG_CONSOLE_TIME display time/date info in upper right corner - (requires CFG_CMD_DATE) + (requires CONFIG_CMD_DATE) CONFIG_VIDEO_LOGO display Linux logo in upper left corner CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of @@ -645,103 +645,96 @@ The following options need to be configured: time on others. This setting #define's the initial value of the "loads_echo" environment variable.
-- Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined) +- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined) CONFIG_KGDB_BAUDRATE Select one of the baudrates listed in CFG_BAUDRATE_TABLE, see below.
- Monitor Functions: - CONFIG_COMMANDS - Most monitor functions can be selected (or - de-selected) by adjusting the definition of - CONFIG_COMMANDS; to select individual functions, - #define CONFIG_COMMANDS by "OR"ing any of the - following values: - - #define enables commands: - ------------------------- - CFG_CMD_ASKENV * ask for env variable - CFG_CMD_AUTOSCRIPT Autoscript Support - CFG_CMD_BDI bdinfo - CFG_CMD_BEDBUG * Include BedBug Debugger - CFG_CMD_BMP * BMP support - CFG_CMD_BSP * Board specific commands - CFG_CMD_BOOTD bootd - CFG_CMD_CACHE * icache, dcache - CFG_CMD_CONSOLE coninfo - CFG_CMD_DATE * support for RTC, date/time... - CFG_CMD_DHCP * DHCP support - CFG_CMD_DIAG * Diagnostics - CFG_CMD_DOC * Disk-On-Chip Support - CFG_CMD_DTT * Digital Therm and Thermostat - CFG_CMD_ECHO echo arguments - CFG_CMD_EEPROM * EEPROM read/write support - CFG_CMD_ELF * bootelf, bootvx - CFG_CMD_ENV saveenv - CFG_CMD_FDC * Floppy Disk Support - CFG_CMD_FAT * FAT partition support - CFG_CMD_FDOS * Dos diskette Support - CFG_CMD_FLASH flinfo, erase, protect - CFG_CMD_FPGA FPGA device initialization support - CFG_CMD_HWFLOW * RTS/CTS hw flow control - CFG_CMD_I2C * I2C serial bus support - CFG_CMD_IDE * IDE harddisk support - CFG_CMD_IMI iminfo - CFG_CMD_IMLS List all found images - CFG_CMD_IMMAP * IMMR dump support - CFG_CMD_IRQ * irqinfo - CFG_CMD_ITEST Integer/string test of 2 values - CFG_CMD_JFFS2 * JFFS2 Support - CFG_CMD_KGDB * kgdb - CFG_CMD_LOADB loadb - CFG_CMD_LOADS loads - CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, - loop, loopw, mtest - CFG_CMD_MISC Misc functions like sleep etc - CFG_CMD_MMC * MMC memory mapped support - CFG_CMD_MII * MII utility commands - CFG_CMD_NAND * NAND support - CFG_CMD_NET bootp, tftpboot, rarpboot - CFG_CMD_PCI * pciinfo - CFG_CMD_PCMCIA * PCMCIA support - CFG_CMD_PING * send ICMP ECHO_REQUEST to network host - CFG_CMD_PORTIO * Port I/O - CFG_CMD_REGINFO * Register dump - CFG_CMD_RUN run command in env variable - CFG_CMD_SAVES * save S record dump - CFG_CMD_SCSI * SCSI Support - CFG_CMD_SDRAM * print SDRAM configuration information - (requires CFG_CMD_I2C) - CFG_CMD_SETGETDCR Support for DCR Register access (4xx only) - CFG_CMD_SPI * SPI serial bus support - CFG_CMD_USB * USB support - CFG_CMD_VFD * VFD support (TRAB) - CFG_CMD_BSP * Board SPecific functions - CFG_CMD_CDP * Cisco Discover Protocol support - CFG_CMD_FSL * Microblaze FSL support - ----------------------------------------------- - CFG_CMD_ALL all - - CONFIG_CMD_DFL Default configuration; at the moment - this is includes all commands, except - the ones marked with "*" in the list - above. - - If you don't define CONFIG_COMMANDS it defaults to - CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can - override the default settings in the respective - include file. + Monitor commands can be included or excluded + from the build by using the #include files + "config_cmd_all.h" and #undef'ing unwanted + commands, or using "config_cmd_default.h" + and augmenting with additional #define's + for wanted commands. + + The default command configuration includes all commands + except those marked below with a "*". + + CONFIG_CMD_ASKENV * ask for env variable + CONFIG_CMD_AUTOSCRIPT Autoscript Support + CONFIG_CMD_BDI bdinfo + CONFIG_CMD_BEDBUG * Include BedBug Debugger + CONFIG_CMD_BMP * BMP support + CONFIG_CMD_BSP * Board specific commands + CONFIG_CMD_BOOTD bootd + CONFIG_CMD_CACHE * icache, dcache + CONFIG_CMD_CONSOLE coninfo + CONFIG_CMD_DATE * support for RTC, date/time... + CONFIG_CMD_DHCP * DHCP support + CONFIG_CMD_DIAG * Diagnostics + CONFIG_CMD_DOC * Disk-On-Chip Support + CONFIG_CMD_DTT * Digital Therm and Thermostat + CONFIG_CMD_ECHO echo arguments + CONFIG_CMD_EEPROM * EEPROM read/write support + CONFIG_CMD_ELF * bootelf, bootvx + CONFIG_CMD_ENV saveenv + CONFIG_CMD_FDC * Floppy Disk Support + CONFIG_CMD_FAT * FAT partition support + CONFIG_CMD_FDOS * Dos diskette Support + CONFIG_CMD_FLASH flinfo, erase, protect + CONFIG_CMD_FPGA FPGA device initialization support + CONFIG_CMD_HWFLOW * RTS/CTS hw flow control + CONFIG_CMD_I2C * I2C serial bus support + CONFIG_CMD_IDE * IDE harddisk support + CONFIG_CMD_IMI iminfo + CONFIG_CMD_IMLS List all found images + CONFIG_CMD_IMMAP * IMMR dump support + CONFIG_CMD_IRQ * irqinfo + CONFIG_CMD_ITEST Integer/string test of 2 values + CONFIG_CMD_JFFS2 * JFFS2 Support + CONFIG_CMD_KGDB * kgdb + CONFIG_CMD_LOADB loadb + CONFIG_CMD_LOADS loads + CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, + loop, loopw, mtest + CONFIG_CMD_MISC Misc functions like sleep etc + CONFIG_CMD_MMC * MMC memory mapped support + CONFIG_CMD_MII * MII utility commands + CONFIG_CMD_NAND * NAND support + CONFIG_CMD_NET bootp, tftpboot, rarpboot + CONFIG_CMD_PCI * pciinfo + CONFIG_CMD_PCMCIA * PCMCIA support + CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network + host + CONFIG_CMD_PORTIO * Port I/O + CONFIG_CMD_REGINFO * Register dump + CONFIG_CMD_RUN run command in env variable + CONFIG_CMD_SAVES * save S record dump + CONFIG_CMD_SCSI * SCSI Support + CONFIG_CMD_SDRAM * print SDRAM configuration information + (requires CONFIG_CMD_I2C) + CONFIG_CMD_SETGETDCR Support for DCR Register access + (4xx only) + CONFIG_CMD_SPI * SPI serial bus support + CONFIG_CMD_USB * USB support + CONFIG_CMD_VFD * VFD support (TRAB) + CONFIG_CMD_BSP * Board SPecific functions + CONFIG_CMD_CDP * Cisco Discover Protocol support + CONFIG_CMD_FSL * Microblaze FSL support +
EXAMPLE: If you want all functions except of network support you can write:
- #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET) + #include "config_cmd_all.h" + #undef CONFIG_CMD_NET
Other Commands: fdt (flattened device tree) command: CONFIG_OF_LIBFDT
Note: Don't enable the "icache" and "dcache" commands - (configuration option CFG_CMD_CACHE) unless you know + (configuration option CONFIG_CMD_CACHE) unless you know what you (and your U-Boot users) are doing. Data cache cannot be enabled on systems like the 8xx or 8260 (where accesses to the IMMR region must be @@ -769,7 +762,7 @@ The following options need to be configured:
- Real-Time Clock:
- When CFG_CMD_DATE is selected, the type of the RTC + When CONFIG_CMD_DATE is selected, the type of the RTC has to be selected, too. Define exactly one of the following options:
@@ -790,14 +783,14 @@ The following options need to be configured: When CONFIG_TIMESTAMP is selected, the timestamp (date and time) of an image is printed by image commands like bootm or iminfo. This option is - automatically enabled when you select CFG_CMD_DATE . + automatically enabled when you select CONFIG_CMD_DATE .
- Partition Support: CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION and/or CONFIG_ISO_PARTITION
- If IDE or SCSI support is enabled (CFG_CMD_IDE or - CFG_CMD_SCSI) you must configure support for at least + If IDE or SCSI support is enabled (CONFIG_CMD_IDE or + CONFIG_CMD_SCSI) you must configure support for at least one partition type as well.
- IDE Reset method: @@ -907,8 +900,8 @@ The following options need to be configured: enable this define CONFIG_MMC. The MMC can be accessed from the boot prompt by mapping the device to physical memory similar to flash. Command line is - enabled with CFG_CMD_MMC. The MMC driver also works with - the FAT fs. This is enabled with CFG_CMD_FAT. + enabled with CONFIG_CMD_MMC. The MMC driver also works with + the FAT fs. This is enabled with CONFIG_CMD_FAT.
- Journaling Flash filesystem support: CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE, @@ -1220,7 +1213,7 @@ The following options need to be configured: include the appropriate I2C driver for the selected cpu.
This will allow you to use i2c commands at the u-boot - command line (as long as you set CFG_CMD_I2C in + command line (as long as you set CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c based realtime clock chips. See common/cmd_i2c.c for a description of the command line interface. @@ -2328,7 +2321,7 @@ Low Level (hardware related) configuration options:
- CONFIG_LOOPW Add the "loopw" memory command. This only takes effect if - the memory commands are activated globally (CFG_CMD_MEM). + the memory commands are activated globally (CONFIG_CMD_MEM).
- CONFIG_MX_CYCLIC Add the "mdc" and "mwc" memory commands. These are cyclic @@ -2342,7 +2335,7 @@ Low Level (hardware related) configuration options: This command will write 12345678 to address 100 all 10 ms.
This only takes effect if the memory commands are activated - globally (CFG_CMD_MEM). + globally (CONFIG_CMD_MEM).
- CONFIG_SKIP_LOWLEVEL_INIT - CONFIG_SKIP_RELOCATE_UBOOT