From: Markus Niebel Markus.Niebel@tqs.de
This patch adds the support for SPI, the serial flash on TQMa6<x> and the two additional CS on MBa6
Signed-off-by: Markus Niebel Markus.Niebel@tq-group.com --- board/tqc/tqma6/tqma6.c | 27 +++++++++++++++++++++++++++ board/tqc/tqma6/tqma6_mba6.c | 24 ++++++++++++++++++++++++ include/configs/tqma6.h | 14 ++++++++++++++ 3 files changed, 65 insertions(+)
diff --git a/board/tqc/tqma6/tqma6.c b/board/tqc/tqma6/tqma6.c index 66fbc06..7c737d1 100644 --- a/board/tqc/tqma6/tqma6.c +++ b/board/tqc/tqma6/tqma6.c @@ -37,6 +37,9 @@ DECLARE_GLOBAL_DATA_PTR; #define GPIO_IN_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+#define SPI_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + int dram_init(void) { gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); @@ -118,6 +121,28 @@ int board_mmc_init(bd_t *bis) return 0; }
+static iomux_v3_cfg_t const tqma6_ecspi1_pads[] = { + /* SS1 */ + NEW_PAD_CTRL(MX6_PAD_EIM_D19__GPIO3_IO19, SPI_PAD_CTRL), + NEW_PAD_CTRL(MX6_PAD_EIM_D16__ECSPI1_SCLK, SPI_PAD_CTRL), + NEW_PAD_CTRL(MX6_PAD_EIM_D17__ECSPI1_MISO, SPI_PAD_CTRL), + NEW_PAD_CTRL(MX6_PAD_EIM_D18__ECSPI1_MOSI, SPI_PAD_CTRL), +}; + +static unsigned const tqma6_ecspi1_cs[] = { + IMX_GPIO_NR(3, 19), +}; + +static void tqma6_iomuxc_spi(void) +{ + unsigned i; + + for (i = 0; i < ARRAY_SIZE(tqma6_ecspi1_cs); ++i) + gpio_direction_output(tqma6_ecspi1_cs[i], 1); + imx_iomux_v3_setup_multiple_pads(tqma6_ecspi1_pads, + ARRAY_SIZE(tqma6_ecspi1_pads)); +} + int board_early_init_f(void) { return tqma6_bb_board_early_init_f(); @@ -128,6 +153,8 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ tqma6_iomuxc_spi(); + tqma6_bb_board_init();
return 0; diff --git a/board/tqc/tqma6/tqma6_mba6.c b/board/tqc/tqma6/tqma6_mba6.c index c30f379..94df68f 100644 --- a/board/tqc/tqma6/tqma6_mba6.c +++ b/board/tqc/tqma6/tqma6_mba6.c @@ -45,6 +45,9 @@ DECLARE_GLOBAL_DATA_PTR; #define GPIO_IN_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+#define SPI_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + #if defined(CONFIG_MX6Q)
#define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII 0x02e0790 @@ -200,6 +203,26 @@ int tqma6_bb_board_mmc_init(bd_t *bis) return 0; }
+static iomux_v3_cfg_t const mba6_ecspi1_pads[] = { + NEW_PAD_CTRL(MX6_PAD_EIM_D24__GPIO3_IO24, SPI_PAD_CTRL), + NEW_PAD_CTRL(MX6_PAD_EIM_D25__GPIO3_IO25, SPI_PAD_CTRL), +}; + +static unsigned const mba6_ecspi1_cs[] = { + IMX_GPIO_NR(3, 24), + IMX_GPIO_NR(3, 25), +}; + +static void mba6_setup_iomuxc_spi(void) +{ + unsigned i; + + for (i = 0; i < ARRAY_SIZE(mba6_ecspi1_cs); ++i) + gpio_direction_output(mba6_ecspi1_cs[i], 1); + imx_iomux_v3_setup_multiple_pads(mba6_ecspi1_pads, + ARRAY_SIZE(mba6_ecspi1_pads)); +} + int board_phy_config(struct phy_device *phydev) { #if defined(CONFIG_MX6Q) @@ -279,6 +302,7 @@ int tqma6_bb_board_early_init_f(void)
int tqma6_bb_board_init(void) { + mba6_setup_iomuxc_spi(); /* do it here - to have reset completed */ mba6_setup_iomuxc_enet();
diff --git a/include/configs/tqma6.h b/include/configs/tqma6.h index 055675e..2c5016d 100644 --- a/include/configs/tqma6.h +++ b/include/configs/tqma6.h @@ -47,6 +47,20 @@ #define CONFIG_MXC_GPIO #define CONFIG_MXC_UART
+/* SPI */ +#define CONFIG_CMD_SPI +#define CONFIG_MXC_SPI + +/* SPI Flash */ +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO + +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(3, 19) << 8)) +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) + /* MMC Configs */ #define CONFIG_FSL_ESDHC #define CONFIG_FSL_USDHC