From: Stefano Babic sbabic@denx.de
Drop local function to setup SDRAM controller and use the common one for i.MX35.
Signed-off-by: Stefano Babic sbabic@denx.de Signed-off-by: Heiko Schocher hs@denx.de ---
board/CarMediaLab/flea3/flea3.c | 93 ++--------------------------------------- 1 file changed, 3 insertions(+), 90 deletions(-)
diff --git a/board/CarMediaLab/flea3/flea3.c b/board/CarMediaLab/flea3/flea3.c index be42863..ca3e44b 100644 --- a/board/CarMediaLab/flea3/flea3.c +++ b/board/CarMediaLab/flea3/flea3.c @@ -30,18 +30,6 @@ #define CCM_CCMR_CONFIG 0x003F4208
#define ESDCTL_DDR2_CONFIG 0x007FFC3F -#define ESDCTL_0x92220000 0x92220000 -#define ESDCTL_0xA2220000 0xA2220000 -#define ESDCTL_0xB2220000 0xB2220000 -#define ESDCTL_0x82228080 0x82228080 -#define ESDCTL_DDR2_EMR2 0x04000000 -#define ESDCTL_DDR2_EMR3 0x06000000 -#define ESDCTL_PRECHARGE 0x00000400 -#define ESDCTL_DDR2_EN_DLL 0x02000400 -#define ESDCTL_DDR2_RESET_DLL 0x00000333 -#define ESDCTL_DDR2_MR 0x00000233 -#define ESDCTL_DDR2_OCD_DEFAULT 0x02000780 -#define ESDCTL_DELAY_LINE5 0x00F49F00
static inline void dram_wait(unsigned int count) { @@ -61,83 +49,6 @@ int dram_init(void) return 0; }
-static void board_setup_sdram_bank(u32 start_address) - -{ - struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR; - u32 *cfg_reg, *ctl_reg; - u32 val; - - switch (start_address) { - case CSD0_BASE_ADDR: - cfg_reg = &esdc->esdcfg0; - ctl_reg = &esdc->esdctl0; - break; - case CSD1_BASE_ADDR: - cfg_reg = &esdc->esdcfg1; - ctl_reg = &esdc->esdctl1; - break; - default: - return; - } - - /* Initialize MISC register for DDR2 */ - val = ESDC_MISC_RST | ESDC_MISC_MDDR_EN | ESDC_MISC_MDDR_DL_RST | - ESDC_MISC_DDR_EN | ESDC_MISC_DDR2_EN; - writel(val, &esdc->esdmisc); - val &= ~(ESDC_MISC_RST | ESDC_MISC_MDDR_DL_RST); - writel(val, &esdc->esdmisc); - - /* - * according to DDR2 specs, wait a while before - * the PRECHARGE_ALL command - */ - dram_wait(0x20000); - - /* Load DDR2 config and timing */ - writel(ESDCTL_DDR2_CONFIG, cfg_reg); - - /* Precharge ALL */ - writel(ESDCTL_0x92220000, - ctl_reg); - writel(0xda, start_address + ESDCTL_PRECHARGE); - - /* Load mode */ - writel(ESDCTL_0xB2220000, - ctl_reg); - writeb(0xda, start_address + ESDCTL_DDR2_EMR2); /* EMRS2 */ - writeb(0xda, start_address + ESDCTL_DDR2_EMR3); /* EMRS3 */ - writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */ - writeb(0xda, start_address + ESDCTL_DDR2_RESET_DLL); /* Reset DLL */ - - /* Precharge ALL */ - writel(ESDCTL_0x92220000, - ctl_reg); - writel(0xda, start_address + ESDCTL_PRECHARGE); - - /* Set mode auto refresh : at least two refresh are required */ - writel(ESDCTL_0xA2220000, - ctl_reg); - writel(0xda, start_address); - writel(0xda, start_address); - - writel(ESDCTL_0xB2220000, - ctl_reg); - writeb(0xda, start_address + ESDCTL_DDR2_MR); - writeb(0xda, start_address + ESDCTL_DDR2_OCD_DEFAULT); - - /* OCD mode exit */ - writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */ - - /* Set normal mode */ - writel(ESDCTL_0x82228080, - ctl_reg); - - dram_wait(0x20000); - - /* Do not set delay lines, only for MDDR */ -} - static void board_setup_sdram(void) { struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR; @@ -146,7 +57,9 @@ static void board_setup_sdram(void) writel(0x2000, &esdc->esdctl0); writel(0x2000, &esdc->esdctl1);
- board_setup_sdram_bank(CSD0_BASE_ADDR); + + mx3_setup_sdram_bank(CSD0_BASE_ADDR, ESDCTL_DDR2_CONFIG, + 13, 10, 2, 0x8080); }
static void setup_iomux_uart3(void)