Add the configurations required for enabling QSPI and the SF command to allow changes to be made dynamically to serial flash devices from the command line interface.
Signed-off-by: Sergiu Moga sergiu.moga@microchip.com Reviewed-by: Tudor Ambarus tudor.ambarus@microchip.com --- configs/sam9x60ek_mmc_defconfig | 13 +++++++++++++ configs/sam9x60ek_nandflash_defconfig | 13 +++++++++++++ 2 files changed, 26 insertions(+)
diff --git a/configs/sam9x60ek_mmc_defconfig b/configs/sam9x60ek_mmc_defconfig index bc0164c38e..cab469877a 100644 --- a/configs/sam9x60ek_mmc_defconfig +++ b/configs/sam9x60ek_mmc_defconfig @@ -33,6 +33,7 @@ CONFIG_CMD_DM=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_SF_TEST=y CONFIG_CMD_NAND=y CONFIG_CMD_NAND_TRIMFFS=y # CONFIG_CMD_SETEXPR is not set @@ -63,6 +64,8 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ATMEL=y CONFIG_MTD=y CONFIG_MTD_RAW_NAND=y +CONFIG_SF_DEFAULT_MODE=0x0 +CONFIG_SF_DEFAULT_SPEED=50000000 CONFIG_NAND_ATMEL=y CONFIG_ATMEL_NAND_HW_PMECC=y CONFIG_PMECC_CAP=8 @@ -84,3 +87,13 @@ CONFIG_W1_GPIO=y CONFIG_W1_EEPROM=y CONFIG_W1_EEPROM_DS24XXX=y CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_SPI_FLASH=y +CONFIG_DM_SPI_FLASH=y +CONFIG_ATMEL_QSPI=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH_MTD=y diff --git a/configs/sam9x60ek_nandflash_defconfig b/configs/sam9x60ek_nandflash_defconfig index 5c34f089e6..7c1a473208 100644 --- a/configs/sam9x60ek_nandflash_defconfig +++ b/configs/sam9x60ek_nandflash_defconfig @@ -33,6 +33,7 @@ CONFIG_CMD_DM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y +CONFIG_CMD_SF_TEST=y CONFIG_CMD_MMC=y CONFIG_CMD_NAND=y CONFIG_CMD_NAND_TRIMFFS=y @@ -69,6 +70,15 @@ CONFIG_ATMEL_NAND_HW_PMECC=y CONFIG_PMECC_CAP=8 CONFIG_SYS_NAND_ONFI_DETECTION=y CONFIG_PHY_MICREL=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SF_DEFAULT_BUS=0 +CONFIG_SF_DEFAULT_SPEED=50000000 +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_ATMEL=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_SST=y CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y @@ -78,6 +88,9 @@ CONFIG_DEBUG_UART_ANNOUNCE=y CONFIG_ATMEL_USART=y CONFIG_SYSRESET=y CONFIG_SYSRESET_AT91=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_ATMEL_QSPI=y CONFIG_TIMER=y CONFIG_ATMEL_PIT_TIMER=y CONFIG_W1=y